SERIES FEED FAN-BEAM ANTENNA ARRAY WITH A LOW SIDELOBE LEVEL FOR POSITIONING SYSTEM

2020 ◽  
pp. 55-65
Author(s):  
Le Minh Thuy
Keyword(s):  
Antenna Array ◽  
Radiation Pattern ◽  
Amplitude Distribution ◽  
High Gain ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Positioning System ◽  
Sidelobe Level ◽  
Single Antenna ◽  
Low Sidelobe

In this paper, a novel antenna array at 5GHz is presented with a low sidelobe level and wide impedance bandwidth for indoor positioning applications . The antenna array has the size of 450 ×57×0.8 mm3 with the high gain of 14.5dBi and the low SLL of -18 dB at 5GHz. The series feed using Unequal Split T-Junction is proposed with the Chebyshev-amplitude distribution to improve SLL. Besides the 1800 phase and amplitude distribution, by deploying driven elements above each single antenna element, the radiation pattern and the gain of the antenna aray are significantly improved.

scholarly journals Triangular Slot-Loaded Wideband Planar Rectangular Antenna Array for Millimeter-Wave 5G Applications

Electronics ◽  
2021 ◽  
Vol 10 (7) ◽  
pp. 778
Author(s):  
Iftikhar Ahmad ◽  
Houjun Sun ◽  
Umair Rafique ◽  
Zhang Yi
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Communication Systems ◽  
Ground Plane ◽  
Simulated Data ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Single Antenna ◽  
Rectangular Patch ◽  
Half Power

This paper presents a design of a triangular slot-loaded planar rectangular antenna array for wideband millimeter-wave (mm-wave) 5G communication systems. The proposed array realizes an overall size of 35.5 × 14.85 mm2. To excite the array elements, a four-way broadband corporate feeding network was designed and analyzed. The proposed array offered a measured impedance bandwidth in two different frequency ranges, i.e., from 23 to 24.6 GHz and from 26 to 45 GHz. The single-antenna element of the array consists of a rectangular patch radiator with a triangular slot. The partial ground plane was used at the bottom side of the substrate to obtain a wide impedance bandwidth. The peak gain in the proposed array is ≈12 dBi with a radiation efficiency of >90%. Furthermore, the array gives a half-power beamwidth (HPBW) of as low as 12.5°. The proposed array has been fabricated and measured, and it has been observed that the measured results are in agreement with the simulated data.

scholarly journals Design of Wideband Slot Antenna Array with Stereoscopic Differentially Fed Structures

2019 ◽  
Vol 2019 ◽  
pp. 1-14 ◽  
Author(s):  
Guang Sun ◽  
Ge Gao ◽  
Tingting Liu ◽  
Yi Liu ◽  
Hu Yang
Keyword(s):  
Antenna Array ◽  
High Gain ◽  
Radar System ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Radiation Characteristics ◽  
Wide Bandwidth ◽  
Feeding Structure

In this paper, a wideband slot antenna element and its array with stereoscopic differentially fed structures are proposed for the radar system. Firstly, a series of slots and a stereoscopic differentially fed structure are designed for the antenna element, which makes it possess a wide bandwidth, stable radiation characteristics, and rather high gain. Moreover, the stereoscopic feeding structure can firmly support the antenna’s radiation structure and reduce the influence of feeding connectors on radiating performance. Secondly, a 4 × 4 array is designed using the proposed antenna element. And a hierarchical feeding network is designed for the array on the basis of the stereoscopic differentially fed structure. For validation, the antenna element and 4 × 4 array are both fabricated and measured: (1) the measured −10 dB impedance bandwidth of the antenna element is 62% (6.8–12.9 GHz) and the gain within the entire band is 5–9.7 dBi and (2) the measured −10 dB impedance bandwidth of the array is approximately 50% (7 to 12 GHz) with its gain being 14–19.75 dBi within the entire band. Notably, measured results agree well with simulations and show great advantages over other similar antennas on bandwidth and gain.

scholarly journals 3D Printed High Gain Complementary Dipole/Slot Antenna Array

2018 ◽  
Vol 8 (8) ◽  
pp. 1410 ◽  
Author(s):  
Kwok So ◽  
Kwai Luk ◽  
Chi Chan ◽  
Ka Chan
Keyword(s):  
Antenna Array ◽  
High Gain ◽  
Dipole Antenna ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Frequency Range ◽  
Operating Frequency Range ◽  
3D Printed ◽  
Stable Frequency

By employing the complementary dipole antenna concept to the normal waveguide fed slot radiator, an improved antenna element with wide impedance bandwidth and symmetrical radiation patterns is developed. This is achieved by mounting two additional metallic cuboids on the top of the slot radiator, which is equivalent to adding an electric dipole on top of the magnetic dipole due to the slot radiator. Then, a high-gain antenna array was designed based on the improved element and fabricated, using 3D printing technology, with stable frequency characteristics operated at around 28 GHz. This was followed by metallization via electroplating. Analytical results agree well with the experimental results. The measured operating frequency range for the reflection coefficient ≤−15 dB is from 25.7 GHz to 29.8 GHz; its corresponding fractional impedance bandwidth is 14.8%. The measured gain is approximately 32 dBi, with the 3 dB beamwidth around 4°.

scholarly journals Wideband and High-Efficiency SIW Cavity-Backed Magneto-Electric Dipole Antenna Array

2019 ◽  
Vol 2019 ◽  
pp. 1-16
Author(s):  
Guang Sun ◽  
Yi Liu ◽  
Taolin Liu ◽  
Hu Yang
Keyword(s):  
Antenna Array ◽  
Printed Circuit Board ◽  
High Efficiency ◽  
High Gain ◽  
Dipole Antenna ◽  
Circuit Board ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Substrate Integrated Waveguide ◽  
Printed Circuit

In this paper, a compact, wideband, and high-efficiency substrate integrated waveguide (SIW) feeding cavity-backed aperture-coupled magneto-electric (ME) dipole antenna element and its array are proposed. Firstly, an SIW cavity-backed and a modified bowtie dipole are designed for the antenna element which makes it possess a high gain and wide impedance bandwidth. The antenna element covers an impedance bandwidth of 66.3% from 10.7 to 21.3 GHz with a peak gain of 10.3 dBi. Secondly, a 4 × 4 array is designed using the proposed antenna element. And a full-corporate substrate integrated waveguide feeding network is introduced to excite the array elements for the antenna application with wide bandwidth and high efficiency. For validation, a prototype of 4 × 4 array is fabricated by standard printed circuit board (PCB) facilities and further measured. The measured −10 dB impedance bandwidth of the proposed 4 × 4 antenna array is 30% (12.75–17.25 GHz) with its gain being 18.2–20.9 dBi within the entire band. The measured maximum aperture efficiency of the antenna array is 94% at 14.92 GHz. Notably, the measured results agree well with simulations, and it shows great advantages over other similar antennas on efficiency and bandwidth.

scholarly journals A DR Loaded Substrate Integrated Waveguide Antenna for 60 GHz High Speed Wireless Communication Systems

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Nadeem Ashraf ◽  
Hamsakutty Vettikalladi ◽  
Majeed A. S. Alkanhal
Keyword(s):  
Antenna Array ◽  
Communication Systems ◽  
High Speed ◽  
Metal Layer ◽  
Simulation Software ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Substrate Integrated Waveguide ◽  
60 Ghz ◽  
Single Antenna

The concept of substrate integrated waveguide (SIW) technology along with dielectric resonators (DR) is used to design antenna/array for 60 GHz communication systems. SIW is created in the substrate of RT/duroid 5880 having relative permittivityεr=2.23and loss tangenttan⁡δ=0.003. H-shaped longitudinal slot is engraved at the top metal layer of the substrate. Two pieces of the DR are placed on the slot without any air gap. The antenna structures are modeled using CST Microwave Studio and then the results are verified using another simulation software HFSS. Simulation results of the two designs are presented; first a single antenna element and then to enhance the gain of the system a broadside array of1×4is presented in the second design. For the single antenna element, the impedance bandwidth is 10.33% having a gain up to 5.5 dBi. Whereas in an array of1×4elements, the impedance bandwidth is found to be 10.70% with a gain up to 11.20 dBi. For the single antenna element and1×4antenna array, the simulated radiation efficiency is found to be 81% and 78%, respectively.

scholarly journals Minimized Triple-Band Eight-Element Antenna Array for 5G Metal-frame Smartphone Applications

Micromachines ◽  
2022 ◽  
Vol 13 (1) ◽  
pp. 136
Author(s):  
Jianlin Huang ◽  
Zhuoni Chen ◽  
Qibo Cai ◽  
Tian Hong Loh ◽  
Gui Liu
Keyword(s):  
Antenna Array ◽  
Multiple Input Multiple Output ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Total Efficiency ◽  
Smartphone Applications ◽  
Single Antenna ◽  
Metal Frame ◽  
5 Ghz ◽  
Triple Band

A multiple-input-multiple-output (MIMO) antenna array for triple-band 5G metal-frame smartphone applications is proposed in this paper. Each single antenna element consists of an S-shaped feeding strip and an L-shaped radiation strip on the metal frame. The dimension of the antenna element is only 6.5 mm × 7 mm (0.076 λ0 × 0.082 λ0, λ0 is the free-space wavelength at the frequency of 3.5 GHz). The −6 dB impedance bandwidth of the proposed eight-antenna array can cover 3.3–3.8 GHz, 4.8–5 GHz, and 5.15–5.925 GHz. The evolution design and the analysis of the optimal parameters for a single antenna element are derived to investigate the principle of the antenna. The measured total efficiency is larger than 70%. The measured isolation is better than 13 dB. The measurements of the prototype agree well with the simulation results.

scholarly journals Decoupled and Descattered Monopole MIMO Antenna Array with Orthogonal Radiation Patterns

2020 ◽  
Author(s):  
Hussain Al-Rizzo ◽  
Ayman A. Isaac ◽  
Sulaiman Z. Tariq ◽  
Samer Yahya
Keyword(s):  
Antenna Array ◽  
Mutual Coupling ◽  
Ground Plane ◽  
Design Concept ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Radiation Patterns ◽  
Mimo Antenna ◽  
Single Antenna ◽  
Novel Design

This chapter introduces a novel design concept to reduce mutual coupling among closely-spaced antenna elements of a MIMO array. This design concept significantly reduces the complexity of traditional/existing design approaches such as metamaterials, defected ground plane structures, soft electromagnetic surfaces, parasitic elements, matching and decoupling networks using a simple, yet a novel design alternative. The approach is based on a planar single decoupling element, consisting of a rectangular metallic ring resonator printed on one face of an ungrounded substrate. The decoupling structure surrounds a two-element vertical monopole antenna array fed by a coplanar waveguide structure. The design is shown both by simulations and measurements to reduce the mutual coupling by at least 20 dB, maintain the impedance bandwidth over which S11, is less than −10 dB, and reduce the envelope correlation coefficient to below 0.001. The boresight of the far-field radiation patterns of the two vertical monopole wire antennas operating at 2.4 GHz and separated by 8 mm (λo/16), where λo is the free-space wavelength at 2.45 GHz, is shown to be orthogonal and inclined by 45° with respect to the horizontal (azimuthal) plane while maintaining the shape of the isolated single antenna element.

scholarly journals A 8x1 Sprout-Shaped Antenna Array with Low Sidelobe Level of -25 dB

2017 ◽  
Author(s):  
Tang The Toan ◽  
Nguyen Minh Tran ◽  
Truong Vu Bang Giang
Keyword(s):  
Antenna Array ◽  
Amplitude Distribution ◽  
Sidelobe Level ◽  
Low Sidelobe ◽  
Point To Point ◽  
Good Agreement

This paper proposes a 8 x 1 sprout-shaped antenna array with low sidelobe level (SLL) for outdoor point to point applications. The array has the dimensions of 165 mm x 195 mm x 1.575 mm and is designed on Rogers RT/Duroid 5870tm with the thickness of 1.575 mm and permittivity of 2.33. In order to achieve low SLL, Chebyshev distribution weights corresponding to SLL preset at -30 dB has been applied to design the feed of the array. Unequal T-junction dividers has been used to ensure that the output powers are proportional to the Chebyshev amplitude distribution. A reflector has been added to the back of the antenna to improve the directivity. The simulated results show that the proposed array can work at 4.95 GHz with the bandwidth of 185 MHz. Moreover, it can provide the gain up to 12.9 dBi and SLL suppressed to -25 dB. A prototype has also been fabricated and measured. A good agreement between simulation and measurement has been obtained. It is proved that the array can be a good candidate for point to point communications.

scholarly journals A Broadband High-Gain Printed Antenna Array Using Dipole and Loop Patches for 5G Communication Systems

2021 ◽  
Vol 15 ◽  
pp. 42-45
Author(s):  
Yuanzhi Liu ◽  
Mustapha C.E. Yagoub
Keyword(s):  
Antenna Array ◽  
Communication Systems ◽  
Low Cost ◽  
High Gain ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Wave Band ◽  
Printed Antenna ◽  
Compact Size ◽  
5G Communication

A broadband and high-gain printed antenna array is presented in this paper. Its single antenna element consists of a loop and two symmetric dipole patches, making the element exhibiting broad impedance bandwidth and improved gain at the targeted frequency, which is 28 GHz, one of the 5G mm-wave band, for this design. An 8×3 antenna array fed by a microstrip line feed network was designed and simulated. With a compact size of 98×32.5 mm2 , the array presents a broad -10 dB impedance bandwidth of 6.8 GHz (24.3%) and a high gain of 18 dBi at 28 GHz. Besides, the single-layered array also features low profile, simple geometry, and low cost, making it a good candidate for 5G communication systems.

Sign in / Sign up

Export Citation Format

Share Document