scholarly journals Double Overt-Leaf Shaped CPW-Fed Four Port UWB MIMO Antenna

Electronics ◽  
2021 ◽  
Vol 10 (24) ◽  
pp. 3140
Author(s):  
Shobit Agarwal ◽  
Umair Rafique ◽  
Rizwan Ullah ◽  
Shakir Ullah ◽  
Salahuddin Khan ◽  
...  
Keyword(s):  
Frequency Band ◽  
Impedance Matching ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Single Element ◽  
Mimo Antenna ◽  
Single Antenna ◽  
Isolation Performance ◽  
Diversity Technique

This paper presents a 4 × 4 multi-input multi-output antenna array for ultra-wideband applications. The single element of the array is comprised of a modified co-planar waveguide-fed double overt-leaf shaped patch radiator. The co-planar ground is optimized to achieve maximum impedance matching in the operating frequency band. The results show that the single antenna element offers an impedance bandwidth of 13.2 GHz starting from 3.2 GHz to 16.7 GHz. It is also observed from the results that the antenna offers good radiation characteristics and acceptable gain for the frequency band of interest. Furthermore, a 4 × 4 MIMO array is designed by utilizing the polarization diversity technique. To improve the isolation performance among antenna elements, a fan-shaped decoupler is introduced on the other side of the substrate, which ensures minimum isolation of 20 dB. Moreover, the proposed MIMO array operates in the frequency range of 2.75–16.05 GHz. The proposed MIMO array is fabricated and measured for the validation of simulation results, and it is observed that both the results are well in agreement.

Dual circularly polarized multilayer MIMO antenna array with an enhanced SR-feeding network for C-band application

2017 ◽  
Vol 9 (8) ◽  
pp. 1741-1748 ◽  
Author(s):  
Mahdi Jalali ◽  
Mohammad Naser-Moghadasi ◽  
Ramezan Ali Sadeghzadeh
Keyword(s):  
Antenna Array ◽  
Tai Chi ◽  
Impedance Matching ◽  
Axial Ratio ◽  
Wide Band ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Circularly Polarized ◽  
Mimo Antenna ◽  
Feed Network

Wide-band circularly polarized multi-input multi-output (MIMO) antenna array with a 2 × 4 feed network was proposed for C-band application. Different unique techniques were utilized in the proposed array to enhance the antenna characteristics, such as gain, 3 dB axial ratio bandwidth (ARBW), impedance tuning, and ruinous mutual coupling effects. A miniaturized dual-feed Tai chi-shaped antenna element with a pair of feeding points and a pair of eyebrow-shaped strips was presented for enhancing circular polarization (CP) purity and impedance matching. For a better improvement of CP features, a 2*4 MIMO sequentially rotated (MIMO-SR) feed network was used to achieve broader 3 dB ARBW. Besides, the MIMO feature of the feed network could control the left- and right-handed CP, respectively. Ultimately, specific forms of slot and slit structures were applied onto the top layer of MIMO feed network that provided a high isolation between the radiating elements and array network. Furthermore, the diversity gain (DG) was studied. The extracted measured results illustrated an impedance bandwidth of 3.5–8.2 GHz at port 1 and 3.5–8.3 GHz at port 2 for VWSR < 2 and 3 dB ARBW of 4.6–7.6 GHz at port 1 and 4.6–7.5 GHz at port 2. The peak gain of 9.9 dBi was at 6 GHz.

scholarly journals Mutual Coupling Reduction Using a Protruded Ground Branch Structure in a Compact UWB Owl-Shaped MIMO Antenna

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
A. Mchbal ◽  
N. Amar Touhami ◽  
H. Elftouh ◽  
A. Dkiouak
Keyword(s):  
Mutual Coupling ◽  
Impedance Matching ◽  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Monopole Antenna ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Mimo Antenna ◽  
Input Multiple Output ◽  
Uwb Applications

A compact ultra-wideband (UWB) multiple input-multiple output (MIMO) antenna with high isolation is designed for UWB applications. The proposed MIMO antenna consists of two identical monopole antenna elements. To enhance the impedance matching, three slots are formed on the ground plane. The arc structure as well as the semicircle with an open-end slot is employed on the radiating elements the fact which helps to extend the impedance bandwidth of the monopole antenna from 3.1 up to 10.6 GHz, which corresponds to the UWB band. A ground branch decoupling structure is introduced between the two elements to reduce the mutual coupling. Simulation and measurement results show a bandwidth range from 3.1 to 11.12 GHz with |S11_|<−15 dB, |S21_|<−20 dB, and ECC < 0.002.

scholarly journals High-Isolation UWB MIMO Antenna with Multiple X-Shaped Stubs Loaded between Ground Planes

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Minghuan Wang ◽  
Jingchang Nan ◽  
Jing Liu
Keyword(s):  
Frequency Band ◽  
Impedance Matching ◽  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Dielectric Substrate ◽  
Ultra Wideband ◽  
Antenna Structure ◽  
Mimo Antenna ◽  
High Isolation ◽  
Input Multiple Output

A miniaturized ultra-wideband multiple-input multiple-output (UWB MIMO) two-port antenna with high isolation based on FR4 is designed in this article. The size of the antenna is only 18 × 28 × 1.6 mm3. The MIMO antenna consists of two identical antenna elements symmetrically placed on the same dielectric substrate in opposite directions. By loading three crossed X-shaped stubs between two unconnected ground planes, high isolation and good impedance matching are achieved. The working frequency band measured by this UWB MIMO antenna is 1.9–14 GHz, and the isolation is kept above 20.2 dB in the whole analysis frequency band. Good radiation characteristics as well as envelope correlation coefficient (ECC, <0.09), mean effective gain (MEG), and channel capacity loss (CCL) in the passband meet the requirements of the application, which can be applied to the UWB wireless communication system. To verify the applicability of the proposed method for enhancing the isolation between antenna elements, the two-port antenna structure was extended to a four-port antenna structure. In the case of loading the X-shaped stubs to connect to the ground plane, the isolation of the antenna is maintained above 15.5 dB within 1.7–14 GHz.

scholarly journals Decoupled and Descattered Monopole MIMO Antenna Array with Orthogonal Radiation Patterns

2020 ◽  
Author(s):  
Hussain Al-Rizzo ◽  
Ayman A. Isaac ◽  
Sulaiman Z. Tariq ◽  
Samer Yahya
Keyword(s):  
Antenna Array ◽  
Mutual Coupling ◽  
Ground Plane ◽  
Design Concept ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Radiation Patterns ◽  
Mimo Antenna ◽  
Single Antenna ◽  
Novel Design

This chapter introduces a novel design concept to reduce mutual coupling among closely-spaced antenna elements of a MIMO array. This design concept significantly reduces the complexity of traditional/existing design approaches such as metamaterials, defected ground plane structures, soft electromagnetic surfaces, parasitic elements, matching and decoupling networks using a simple, yet a novel design alternative. The approach is based on a planar single decoupling element, consisting of a rectangular metallic ring resonator printed on one face of an ungrounded substrate. The decoupling structure surrounds a two-element vertical monopole antenna array fed by a coplanar waveguide structure. The design is shown both by simulations and measurements to reduce the mutual coupling by at least 20 dB, maintain the impedance bandwidth over which S11, is less than −10 dB, and reduce the envelope correlation coefficient to below 0.001. The boresight of the far-field radiation patterns of the two vertical monopole wire antennas operating at 2.4 GHz and separated by 8 mm (λo/16), where λo is the free-space wavelength at 2.45 GHz, is shown to be orthogonal and inclined by 45° with respect to the horizontal (azimuthal) plane while maintaining the shape of the isolated single antenna element.

scholarly journals Ultra-Wideband Diversity MIMO Antenna System for Future Mobile Handsets

Sensors ◽  
2020 ◽  
Vol 20 (8) ◽  
pp. 2371 ◽  
Author(s):  
Naser Ojaroudi Parchin ◽  
Haleh Jahanbakhsh Basherlou ◽  
Yasir I. A. Al-Yasir ◽  
Ahmed M. Abdulkhaleq ◽  
Raed A. Abd-Alhameed
Keyword(s):  
Multiple Input Multiple Output ◽  
Circular Ring ◽  
Antenna System ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Single Element ◽  
Polarization Diversity ◽  
Mimo Antenna ◽  
Input Multiple Output ◽  
Dual Polarized

A new ultra-wideband (UWB) multiple-input/multiple-output (MIMO) antenna system is proposed for future smartphones. The structure of the design comprises four identical pairs of compact microstrip-fed slot antennas with polarization diversity function that are placed symmetrically at different edge corners of the smartphone mainboard. Each antenna pair consists of an open-ended circular-ring slot radiator fed by two independently semi-arc-shaped microstrip-feeding lines exhibiting the polarization diversity characteristic. Therefore, in total, the proposed smartphone antenna design contains four horizontally-polarized and four vertically-polarized elements. The characteristics of the single-element dual-polarized UWB antenna and the proposed UWB-MIMO smartphone antenna are examined while using both experimental and simulated results. An impedance bandwidth of 2.5–10.2 GHz with 121% fractional bandwidth (FBW) is achieved for each element. However, for S11 ≤ −6 dB, this value is more than 130% (2.2–11 GHz). The proposed UWB-MIMO smartphone antenna system offers good isolation, dual-polarized function, full radiation coverage, and sufficient efficiency. Besides, the calculated diversity performances of the design in terms of the envelope correlation coefficient (ECC) and total active reflection coefficient (TARC) are very low over the entire operating band.

High Isolated MIMO Antenna for WLAN Applications

2021 ◽  
Author(s):  
Param Dev ◽  
Surendra Kumar Gupta ◽  
Amit Bage ◽  
Lakhindar Murmu
Keyword(s):  
Correlation Coefficient ◽  
Frequency Band ◽  
Wireless Local Area Network ◽  
Local Area Network ◽  
Impedance Matching ◽  
Local Area ◽  
Impedance Bandwidth ◽  
Area Network ◽  
Potential Candidate ◽  
Mimo Antenna

This paper presents a compact multiple-inputs multiple-outputs (MIMO) antenna for wireless local area network (WLAN) applications. The proposed four-port MIMO antenna has been incorporated with its four identical elements having dimensions of 10[Formula: see text]mm [Formula: see text] 12[Formula: see text]mm each. The MIMO antenna is designed to operate in the range of 5.17–6.25[Formula: see text]GHz frequency band having impedance bandwidth of 18.91%. The antenna is fabricated on a glass epoxy FR-4 substrate having a thickness of 0.8[Formula: see text]mm for measurement and validation. The measured results show that the antenna has good isolation greater than [Formula: see text]17[Formula: see text]dB to [Formula: see text]25[Formula: see text]dB, better impedance matching and envelope correlation coefficient (ECC) below 0.03 over the entire band of operation. The proposed MIMO antenna is a potential candidate for WLAN applications.

scholarly journals Triangular Slot-Loaded Wideband Planar Rectangular Antenna Array for Millimeter-Wave 5G Applications

Electronics ◽  
2021 ◽  
Vol 10 (7) ◽  
pp. 778
Author(s):  
Iftikhar Ahmad ◽  
Houjun Sun ◽  
Umair Rafique ◽  
Zhang Yi
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Communication Systems ◽  
Ground Plane ◽  
Simulated Data ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Single Antenna ◽  
Rectangular Patch ◽  
Half Power

This paper presents a design of a triangular slot-loaded planar rectangular antenna array for wideband millimeter-wave (mm-wave) 5G communication systems. The proposed array realizes an overall size of 35.5 × 14.85 mm2. To excite the array elements, a four-way broadband corporate feeding network was designed and analyzed. The proposed array offered a measured impedance bandwidth in two different frequency ranges, i.e., from 23 to 24.6 GHz and from 26 to 45 GHz. The single-antenna element of the array consists of a rectangular patch radiator with a triangular slot. The partial ground plane was used at the bottom side of the substrate to obtain a wide impedance bandwidth. The peak gain in the proposed array is ≈12 dBi with a radiation efficiency of >90%. Furthermore, the array gives a half-power beamwidth (HPBW) of as low as 12.5°. The proposed array has been fabricated and measured, and it has been observed that the measured results are in agreement with the simulated data.

A compact dual port UWB-MIMO/diversity antenna for indoor application

2017 ◽  
Vol 10 (3) ◽  
pp. 360-367 ◽  
Author(s):  
Sonika Priyadarsini Biswal ◽  
Sushrut Das
Keyword(s):  
Mimo System ◽  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Open Circuit ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Good Prospect ◽  
Mimo Antenna ◽  
Radiating Element ◽  
Input Multiple Output

A compact printed quadrant shaped monopole antenna is introduced in this paper as a good prospect for ultra wideband- multiple-input multiple-output (UWB-MIMO) system. The proposed MIMO antenna comprises two perpendicularly oriented monopoles to employ polarization diversity. An open circuit folded stub is extended from the ground plane of each radiating element to enhance the impedance bandwidth satisfying the UWB criteria. Two ‘L’ shaped slots are further etched on the radiator to provide good isolation performance between two radiators. The desirable radiator performances and diversity performances are ensured by simulation and/or measurement of the reflection coefficient, radiation pattern, realized peak gain, envelope correlation coefficient (ECC), diversity gain, mean effective gain (MEG) ratio and channel capacity loss (CCL). Results indicate that the proposed antenna exhibits 2.9–11 GHz 10 dB return loss bandwidth, mutual coupling <−20 dB, ECC < 0.003, MEG ratio ≈ 1, and CCL < 0.038 Bpsec/Hz, making it a good candidate for UWB and MIMO diversity application.

Design of an interlocked four-port MIMO antenna for UWB automotive communications

2021 ◽  
pp. 1-8
Author(s):  
M. Saravanan ◽  
R. Kalidoss ◽  
B. Partibane ◽  
K. S. Vishvaksenan
Keyword(s):  
Multiple Input Multiple Output ◽  
Performance Estimation ◽  
Ultra Wideband ◽  
Antenna Element ◽  
Frequency Range ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Operating Bandwidth ◽  
Peak Gain

Abstract The design, analysis, fabrication, and testing of a four-port multiple-input multiple-output (MIMO) antenna is reported in this paper for automotive communications. The MIMO antenna is constructed using the basic antenna element exploiting a slot geometry. Two such antennas are developed on the same microwave laminate to develop a two-port MIMO antenna. Two such microwave laminates are interlocked to create the four-port MIMO scheme. The most distinct feature of the proposed architecture is that the inter-port isolation is well-taken care without the need for an external decoupling unit. The four-port MIMO antenna has an overall volume of 32 × 15 × 32 mm3. The prototype MIMO antenna is fabricated and the measurements are carried out to validate the simulation results. The antenna offers ultra-wideband (UWB) characteristics covering the frequency range of 2.8–9.5 GHz. The average boresight gain of the antenna ranges from 3.2 to 5.41 dBi with the peak gain at 8 GHz. The simulated efficiency of the antenna is greater than 73% within the operating bandwidth. The MIMO parameters such as envelope correlation coefficient, diversity gain, and mean effective gain are evaluated and presented. The appropriateness of the proposed antenna for deployment in the shark fin housing of the present-day automobiles is verified using on-car performance estimation.

scholarly journals High gain 5G MIMO antenna for mobile base station

2019 ◽  
Vol 9 (1) ◽  
pp. 468 ◽  
Author(s):  
Yusnita Rahayu ◽  
Indah Permata Sari ◽  
Dara Incam Ramadhan ◽  
Razali Ngah
Keyword(s):  
Linear Array ◽  
Multiple Input Multiple Output ◽  
High Gain ◽  
Base Station ◽  
Impedance Bandwidth ◽  
Single Element ◽  
Mimo Antenna ◽  
Input Multiple Output ◽  
Mobile Base Station ◽  
Mobile Base

This article presented a millimeter wave antenna which operated at 38 GHz for 5G mobile base station. The MIMO (Multiple Input Multiple Output) antenna consisted of 1x10 linear array configurations. The proposed antenna’s size was 88 x 98 mm^2  and printed on 1.575 mm-thick Rogers Duroid 5880 subsrate with dielectric constant of ε_r= 2.2 and loss tangent (tanδ) of 0.0009. The antenna array covered along the azimuth plane to provide the coverage to the users in omnidirection. The simulated results showed that the single element antenna had the reflection coefficient (S11) of -59 dB, less than -10 dB in the frequency range of 35.5 - 39.6 GHz. More than 4.1 GHz of impedance bandwidth was obtained. The gain of the antenna linear array was 17.8 dBi while the suppression of the side lobes was -2.7 dB.  It showed a high array gain throughout the impedance bandwidth with overall of VSWR were below 1.0646. It designed using CST microwave studio.

Sign in / Sign up

Export Citation Format

Share Document