scholarly journals Vibration Characteristics of Compression Ignition Engines Fueled with Blended Petro-Diesel and Fischer-Tropsch Diesel Fuel from Coal Fuels

Energies ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 2043 ◽  
Author(s):  
Tiantian Yang ◽  
Tie Wang ◽  
Guoxing Li ◽  
Jinhong Shi ◽  
Xiuquan Sun
Keyword(s):  
Diesel Fuel ◽  
Pressure Oscillation ◽  
Vibration Signal ◽  
Vibration Characteristics ◽  
Compression Ignition ◽  
Fischer Tropsch ◽  
Frequency Bands ◽  
Transient Combustion ◽  
Block Based ◽  
Ci Engines

Fischer-Tropsch diesel fuel synthesized from coal (CFT) is an alternative fuel that gives excellent emission performance in compression ignition (CI) engines. In order to study the vibration characteristics, which are important for determining the applicability of the fuel, CFT-diesel blends were tested on a CI engine to acquire vibration signals from the engine head and block. Based on the FFT and continuous wavelet transformation (CWT) analysis, the influence of CFT on the vibration was studied. The results showed that the root mean square (RMS) values of the vibration signal decrease as the proportion of CFT in the blends increases. The CWT results indicated that the vibration energy areas motivated by the pressure shock of transient combustion were weak with increasing CFT proportion for the different frequency bands. The blend of 90% pure petro-diesel and 10% CFT registered the largest RMS value for piston side thrust response, and the RMS of high-frequency pressure oscillation response is greater than that of the main response of combustion, for FT30. Therefore, CFT has the potential to reduce the combustion vibration of the engine at all frequency bands, and there is a possibility that the proportion of blended fuel can be modified to satisfy the vibration characteristics requirements in different frequency bands.

Binary Biodiesel Blend Endurance Characteristics in a Compression Ignition Engine

2018 ◽  
Vol 141 (3) ◽  
Author(s):  
Paramvir Singh ◽  
S. R. Chauhan ◽  
Varun Goel ◽  
Ashwani K. Gupta
Keyword(s):  
Diesel Fuel ◽  
Biodiesel Fuel ◽  
Engine Fuel ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Blend ◽  
Engine Operation ◽  
Endurance Tests ◽  
Ci Engines

The results obtained on wear assessment from a compression ignition (CI) engine fueled with a blend of 70% amla seed biodiesel (AB) and 30% eucalyptus oil (EU) on volume basis (called AB70EU30). The results showed stable engine operation and good operability of the engine-fuel system with the binary biodiesel fuel blend. The feasibility of this blend over a long-term endurance tests was explored. The specific assessment examination included the fate of cylinder head, pump plunger, injector nozzle, and piston crown, which affects the engine performance and engine life. The experimental results revealed better tribological performance characteristics with the binary fuel blend as compared to contemporary diesel fuel. No specific problem was encountered during the long-term endurance tests with the binary fuel blend using the modified engine parameters. The results show that the binary fuel mixture offers good potential for use as diesel fuel in CI engines while maintaining good performance and endurance.

Mapping the combustion modes of a dual-fuel compression ignition engine

2021 ◽  
pp. 146808742110183
Author(s):  
Jonathan Martin ◽  
André Boehman
Keyword(s):  
Direct Injection ◽  
Fuel Combustion ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Combustion Modes ◽  
Si Engines ◽  
Dual Fuel Combustion ◽  
Soot Emissions ◽  
Ci Engines

Compression-ignition (CI) engines can produce higher thermal efficiency (TE) and thus lower carbon dioxide (CO2) emissions than spark-ignition (SI) engines. Unfortunately, the overall fuel economy of CI engine vehicles is limited by their emissions of nitrogen oxides (NOx) and soot, which must be mitigated with costly, resource- and energy-intensive aftertreatment. NOx and soot could also be mitigated by adding premixed gasoline to complement the conventional, non-premixed direct injection (DI) of diesel fuel in CI engines. Several such “dual-fuel” combustion modes have been introduced in recent years, but these modes are usually studied individually at discrete conditions. This paper introduces a mapping system for dual-fuel CI modes that links together several previously studied modes across a continuous two-dimensional diagram. This system includes the conventional diesel combustion (CDC) and conventional dual-fuel (CDF) modes; the well-explored advanced combustion modes of HCCI, RCCI, PCCI, and PPCI; and a previously discovered but relatively unexplored combustion mode that is herein titled “Piston-split Dual-Fuel Combustion” or PDFC. Tests show that dual-fuel CI engines can simultaneously increase TE and lower NOx and/or soot emissions at high loads through the use of Partial HCCI (PHCCI). At low loads, PHCCI is not possible, but either PDFC or RCCI can be used to further improve NOx and/or soot emissions, albeit at slightly lower TE. These results lead to a “partial dual-fuel” multi-mode strategy of PHCCI at high loads and CDC at low loads, linked together by PDFC. Drive cycle simulations show that this strategy, when tuned to balance NOx and soot reductions, can reduce engine-out CO2 emissions by about 1% while reducing NOx and soot by about 20% each with respect to CDC. This increases emissions of unburnt hydrocarbons (UHC), still in a treatable range (2.0 g/kWh) but five times as high as CDC, requiring changes in aftertreatment strategy.

scholarly journals A Comparative Study of Biofuels and Fischer–Tropsch Diesel Blends on the Engine Combustion Performance for Reducing Exhaust Gaseous and Particulate Emissions

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1538
Author(s):  
Felipe Andrade Torres ◽  
Omid Doustdar ◽  
Jose Martin Herreros ◽  
Runzhao Li ◽  
Robert Poku ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Road Transport ◽  
Oxidation Catalyst ◽  
Transport Sector ◽  
Particulate Emissions ◽  
Gaseous Emissions ◽  
Fischer Tropsch ◽  
Engine Combustion

The worldwide consumption of fossil hydrocarbons in the road transport sector in 2020 corresponded to roughly half of the overall consumption. However, biofuels have been discreetly contributing to mitigate gaseous emissions and participating in sustainable development, and thus leading to the extending of the commercial utilization of internal combustion engines. In this scenario, the present work aims at exploring the effects of alternative fuels containing a blend of 15% ethanol and 35% biodiesel with a 50% fossil diesel (E15D50B35) or 50% Fischer–Tropsch (F-T) diesel (E15FTD50B35) on the engine combustion, exhaust emissions (CO, HC, and NOx), particulate emissions characteristics as well as the performance of an aftertreatment system of a common rail diesel engine. It was found that one of the blends (E15FTD50B35) showed more than 30% reduction in PM concentration number, more than 25% reduction in mean particle size, and more than 85% reduction in total PM mass with respect to conventional diesel fuel. Additionally, it was found that the E15FTD50B35 blend reduces gaseous emissions of total hydrocarbons (THC) by more than 25% and NO by 3.8%. The oxidation catalyst was effective in carbonaceous emissions reduction, despite the catalyst light-off being slightly delayed in comparison to diesel fuel blends.

Experimental Investigation of a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

2019 ◽  
Vol 141 (11) ◽  
Author(s):  
Jinlong Liu ◽  
Hemanth Kumar Bommisetty ◽  
Cosmin Emil Dumitrescu
Keyword(s):  
Natural Gas ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Compression Ignition ◽  
Heavy Duty ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Cycle Variation ◽  
Spark Timing ◽  
Ci Engines

Heavy-duty compression-ignition (CI) engines converted to natural gas (NG) operation can reduce the dependence on petroleum-based fuels and curtail greenhouse gas emissions. Such an engine was converted to premixed NG spark-ignition (SI) operation through the addition of a gas injector in the intake manifold and of a spark plug in place of the diesel injector. Engine performance and combustion characteristics were investigated at several lean-burn operating conditions that changed fuel composition, spark timing, equivalence ratio, and engine speed. While the engine operation was stable, the reentrant bowl-in-piston (a characteristic of a CI engine) influenced the combustion event such as producing a significant late combustion, particularly for advanced spark timing. This was due to an important fraction of the fuel burning late in the squish region, which affected the end of combustion, the combustion duration, and the cycle-to-cycle variation. However, the lower cycle-to-cycle variation, stable combustion event, and the lack of knocking suggest a successful conversion of conventional diesel engines to NG SI operation using the approach described here.

scholarly journals A Multicomponent Blend as a Diesel Fuel Surrogate for Compression Ignition Engine Applications

2015 ◽  
Vol 137 (11) ◽  
Author(s):  
Yuanjiang Pei ◽  
Marco Mehl ◽  
Wei Liu ◽  
Tianfeng Lu ◽  
William J. Pitz ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Flow Reactor ◽  
Expert Knowledge ◽  
Combustion Model ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Combined Mechanism ◽  
Fuel Surrogate ◽  
Skeletal Mechanism

A mixture of n-dodecane and m-xylene is investigated as a diesel fuel surrogate for compression ignition (CI) engine applications. Compared to neat n-dodecane, this binary mixture is more representative of diesel fuel because it contains an alkyl-benzene which represents an important chemical class present in diesel fuels. A detailed multicomponent mechanism for n-dodecane and m-xylene was developed by combining a previously developed n-dodecane mechanism with a recently developed mechanism for xylenes. The xylene mechanism is shown to reproduce experimental ignition data from a rapid compression machine (RCM) and shock tube (ST), speciation data from the jet stirred reactor and flame speed data. This combined mechanism was validated by comparing predictions from the model with experimental data for ignition in STs and for reactivity in a flow reactor. The combined mechanism, consisting of 2885 species and 11,754 reactions, was reduced to a skeletal mechanism consisting 163 species and 887 reactions for 3D diesel engine simulations. The mechanism reduction was performed using directed relation graph (DRG) with expert knowledge (DRG-X) and DRG-aided sensitivity analysis (DRGASA) at a fixed fuel composition of 77% of n-dodecane and 23% m-xylene by volume. The sample space for the reduction covered pressure of 1–80 bar, equivalence ratio of 0.5–2.0, and initial temperature of 700–1600 K for ignition. The skeletal mechanism was compared with the detailed mechanism for ignition and flow reactor predictions. Finally, the skeletal mechanism was validated against a spray flame dataset under diesel engine conditions documented on the engine combustion network (ECN) website. These multidimensional simulations were performed using a representative interactive flame (RIF) turbulent combustion model. Encouraging results were obtained compared to the experiments with regard to the predictions of ignition delay and lift-off length at different ambient temperatures.

Comprehensive Study on the Effect of CuO Nano Fluids Prepared Using One-Step Chemical Synthesis Method on the Behavior of Waste Cooking Oil Biodiesel in Compression Ignition Engine

2019 ◽  
Vol 11 (4) ◽  
Author(s):  
Ramanathan Velmurugan ◽  
Jaikumar Mayakrishnan ◽  
S. Induja ◽  
Selvakumar Raja ◽  
Sasikumar Nandagopal ◽  
...  
Keyword(s):  
Chemical Synthesis ◽  
Vegetable Oil ◽  
Diesel Fuel ◽  
Synthesis Method ◽  
Waste Cooking Oil ◽  
Compression Ignition ◽  
Cooking Oil ◽  
One Step ◽  
Ci Engine ◽  
The Impact

Vegetable oil is considered as one among the promising alternatives for diesel fuel as it holds properties very close to diesel fuel. However, straight usage of vegetable oil in compression ignition (CI) engine resulted in inferior performance and emission behavior. This can be improved by modifying the straight vegetable oil into its esters, emulsion, and using them as a fuel in CI engine showcased an improved engine behavior. Waste cooking oil (WCO) is one such kind of vegetable oil gained a lot of attraction globally as it is generated in a large quantity locally. The present investigation aims at analyzing various parameters of single cylinder four stroke CI engine fueled with waste cooking oil biodiesel (WCOB), waste cooking oil biodiesel water emulsion (WCOBE) while the engine is operated with a constant speed of 1500 rpm. Furthermore, an attempt is made to study the impact of nanofluids in the behavior of the engine fueled with WCOB blended with nanofluids (WCOBN50). This work also explored a novel method of producing nanofluids using one-step chemical synthesis method. Copper oxide (CuO) nanofluids were prepared by the above mentioned method and blended with waste cooking oil biodiesel (WCOBN50) using ethylene glycol as a suitable emulsifier. Results revealed that brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) of WCOBN50 are significantly improved when compared to WCOB and WCOBE. Furthermore, a higher reduction in oxides of nitrogen (NOx), carbon monoxide (CO), hydrocarbon (HC), and smoke emissions were observed with WCOBN50 on comparison with all other tested fuels at different power outputs. It is also identified that one-step chemical synthesis method is a promising technique for preparing nanofluids with a high range of stability.

Sign in / Sign up

Export Citation Format

Share Document