scholarly journals An Investigation on the Function of Mud Cakes on the Inhibition of Low Molecular Inhibitor for Water-Based Drilling Fluids

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3726 ◽  
Author(s):  
Wenxin Dong ◽  
Xiaolin Pu ◽  
Biao Ma
Keyword(s):  
High Performance ◽  
Drilling Fluid ◽  
Environmental Scanning Electron Microscopy ◽  
Homogeneous Layer ◽  
Environmental Scanning ◽  
Drilling Fluids ◽  
Mud Cake ◽  
Water Based ◽  
Oil And Natural Gas ◽  
Pass Through

The major low molecular inhibitors showed inhibition in the hydration of clay in the laboratory for water-based drilling fluids, according to the principle of intercalation adsorption. However, inhibitors have failed and caused serious engineering accidents in drilling oil and natural gas. This paper investigated the transmission of several of drilling fluids to indicate whether low molecular inhibitor for drilling can effectively inhibit the wellbore hydration. The inhibition of drilling fluid with the plugging of mud cakes, was significantly weakened based on the hydration expansion of cores and cutting recoveries. The residual contents of inhibitors were determined with the precolumn derivation of high-performance liquid chromatography (HPLC) analysis and were chartered with Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR) analysis in the structure of the derivative. The clogging behavior of the mud cake was described by environmental scanning electron microscopy (ESEM). Experiments show that 40 wt% to 90 wt% by weight of the corrosion inhibitor cannot pass through the mud cake in the dynamic filtration of the drilling fluid. The mud cake can be further divided into a nanostructure layer, a homogeneous layer and an anisotropic layer with different permeability. Most inhibitors should be limited to the nanostructure layer and the homogeneous layer.

scholarly journals Thermoresponsive Bentonite for Water-Based Drilling Fluids

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2115 ◽  
Author(s):  
Dong ◽  
Pu ◽  
Ren ◽  
Zhai ◽  
Gao ◽  
...  
Keyword(s):  
High Temperature ◽  
Drilling Fluid ◽  
Environmental Scanning Electron Microscopy ◽  
High Density ◽  
Drilling Fluids ◽  
Isothermal Adsorption ◽  
Mud Cake ◽  
Water Based ◽  
Recovery Behavior ◽  
Increasing Temperature

As an important industrial material, bentonite has been widely applied in water-based drilling fluids to create mud cakes to protect boreholes. However, the common mud cake is porous, and it is difficult to reduce the filtration of a drilling fluid at high temperature. Therefore, this paper endowed bentonite with a thermo response via the insertion of N-isopropylacrylamide (NIPAM) monomers. The interaction between NIPAM monomers and bentonite was investigated via Fourier infrared spectroscopy (FTIR), isothermal adsorption, and X-ray diffraction (XRD) at various temperatures. The results demonstrate that chemical adsorption is involved in the adsorption process of NIPAM monomers on bentonite, and the adsorption of NIPAM monomers accords with the D–R model. With increasing temperature, more adsorption water was squeezed out of the composite when the temperature of the composite exceeded 70 °C. Based on the composite of NIPAM and bentonite, a mud cake was prepared using low-viscosity polyanionic cellulose (Lv-PAC) and initiator potassium peroxydisulfate (KPS). The change in the plugging of the mud cake was investigated via environmental scanning electron microscopy (ESEM), contact angle testing, filtration experiments, and linear expansion of the shale at various temperatures. In the plugging of the mud cake, a self-recovery behavior was observed with increasing temperature, and resistance was observed at 110 °C. The rheology of the drilling fluid was stable in the alterative temperature zone (70–110 °C). Based on the high resistance of the basic drilling fluid, a high-density drilling fluid (ρ = 2.0 g/cm3) was prepared with weighting materials with the objective of drilling high-temperature formations. By using a high-density drilling fluid, the hydration expansion of shale was reduced by half at 110 °C in comparison with common bentonite drilling fluid. In addition, the rheology of the high-density drilling fluid tended to be stable, and a self-recovery behavior was observed.

scholarly journals Laponite: a promising nanomaterial to formulate high-performance water-based drilling fluids

2020 ◽  
Author(s):  
Xian-Bin Huang ◽  
Jin-Sheng Sun ◽  
Yi Huang ◽  
Bang-Chuan Yan ◽  
Xiao-Dong Dong ◽  
...  
Keyword(s):  
High Performance ◽  
Drilling Fluid ◽  
Nitrogen Adsorption ◽  
Drill String ◽  
Wellbore Stability ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Mechanism Analysis ◽  
Water Based ◽  
Inhibition Performance

Abstract High-performance water-based drilling fluids (HPWBFs) are essential to wellbore stability in shale gas exploration and development. Laponite is a synthetic hectorite clay composed of disk-shaped nanoparticles. This paper analyzed the application potential of laponite in HPWBFs by evaluating its shale inhibition, plugging and lubrication performances. Shale inhibition performance was studied by linear swelling test and shale recovery test. Plugging performance was analyzed by nitrogen adsorption experiment and scanning electron microscope (SEM) observation. Extreme pressure lubricity test was used to evaluate the lubrication property. Experimental results show that laponite has good shale inhibition property, which is better than commonly used shale inhibitors, such as polyamine and KCl. Laponite can effectively plug shale pores. It considerably decreases the surface area and pore volume of shale, and SEM results show that it can reduce the porosity of shale and form a seamless nanofilm. Laponite is beneficial to increase lubricating property of drilling fluid by enhancing the drill pipes/wellbore interface smoothness and isolating the direct contact between wellbore and drill string. Besides, laponite can reduce the fluid loss volume. According to mechanism analysis, the good performance of laponite nanoparticles is mainly attributed to the disk-like nanostructure and the charged surfaces.

Sodium Silicate Based Drilling Fluid Application in Gulf of Thailand to Stabilise Wellbore: A Case Study

2021 ◽  
Author(s):  
Waleepon Sukarasep ◽  
Rahul Sukanta Dey ◽  
Visarut Phonpuntin
Keyword(s):  
Sodium Silicate ◽  
High Performance ◽  
Drilling Fluid ◽  
Wellbore Stability ◽  
Drilling Fluids ◽  
Gulf Of Thailand ◽  
Hole Cleaning ◽  
Water Based ◽  
Wellbore Strengthening ◽  
Effective Seal

Abstract Sodium Silicate were first used in water-based drilling fluids to stabilize claystone formations in the 1930's, but found favour in the 1990's in high performance, non dispersed water based systems for drilling problematic claystone formations as an alternative to oil-based drilling fluids. In Bongkot South field, Gulf of Thailand, sodium silicate-based drilling fluid (SSBDF) were used with mixed success in shallow gas drilling. Typically, platform WP-33, the claystone formation of the 12¼" section were drilled with 5% v/v Sodium Silicate in the water based drilling fluid together with excessive circulation as intention to improve hole cleaning frequently result in a wellbore that was overgauge by upto 18.9% in some case. This led to further hole cleaning problem that also compromised cement job quality. A further 6 well campaign on WPS-16 required a re-evaulation of the SSBDF coupled to an understanding of the wellbore instability mechanisms that leads to hole enlargement. To overcome better wellbore stability, sodium silicate has been designed by increased concentration to 8% v/v sodium silicate treated drilling fluid showed optimal design for application base on application of SSBDF has been used on platform WP-11 in 2002. Rheology, hydraulic and flow regime was adjusted for laminar flow that reduced the erosion of fragile claystone formation in the wellbore. The revised SSBDF formulation at WPS-16 result in a significant reduction of hole enlargement to 3.2% in the claystone section through a combination of chemicals and mechanical inhibition that contribute improved hole cleaning. The addition of wellbore strengthening material also provide an effective seal to minimize gas invasion. This paper describes the field trials in the Gulf of Thailand drilled with revised sodium sodium silicate based drilling fluid, the use of wellbore strengthening materials to manage gas influxes, better drilling practice and hydraclic simulation concluded that high performance water based drilling fluid of this nature have wider application where oil-base drilling fluid have traditionally been used.

scholarly journals Reduction of the Probability of Occurrence of Differential Pressure Sticking Through the Use of Diesel on Water Based Drilling Fluids

Enfoque UTE ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 77-88
Author(s):  
David Esteban Almeida Campana ◽  
Marco Loaiza ◽  
Raul Valencia
Keyword(s):  
Drilling Fluid ◽  
Differential Pressure ◽  
Drilling Fluids ◽  
Reservoir Pressure ◽  
Predictive Tool ◽  
Mud Cake ◽  
Pressure Tests ◽  
Water Based ◽  
Additional Barrier ◽  
Bow Tie

The drilling campaign on Pad C of the Tiputini Field, located on the Oriente Basin, Ecuador, started with the first exploratory well TPTC-002. Pressure tests performed on the M1 sandstone of the Napo Formation determined that the average reservoir pressure (Pr) was 1921 psi. Ten months later, Pr averaged 846 psi. This increased the risk of differential pressure sticking, event that indeed occurred while drilling the well TPTC-016. By using the “Bow-Tie” methodology as a predictive tool to analyze risks, and taking into account the preliminary studies that describe this phenomena, a solution was found for stablishing an additional barrier with the use of diesel on the water-based drilling fluid. Diesel was used in order to extend the ‘half value time’ and to decrease the friction coefficient between the mud cake and pipe.

scholarly journals Wet Drilled Cuttings Bed Rheology

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1644
Author(s):  
Camilo Pedrosa ◽  
Arild Saasen ◽  
Bjørnar Lund ◽  
Jan David Ytrehus
Keyword(s):  
Drilling Fluid ◽  
Drilling Fluids ◽  
Parallel Plates ◽  
Single Particles ◽  
Cuttings Transport ◽  
Transport Studies ◽  
Water Based ◽  
Fluid Properties ◽  
External Forces ◽  
Cuttings Bed

The cuttings transport efficiency of various drilling fluids has been studied in several approaches. This is an important aspect, since hole cleaning is often a bottleneck in well construction. The studies so far have targeted the drilling fluid cuttings’ transport capability through experiments, simulations or field data. Observed differences in the efficiency due to changes in the drilling fluid properties and compositions have been reported but not always fully understood. In this study, the cuttings bed, wetted with a single drilling fluid, was evaluated. The experiments were performed with parallel plates in an Anton Paar Physica 301 rheometer. The results showed systematic differences in the internal friction behaviors between tests of beds with oil-based and beds with water-based fluids. The observations indicated that cutting beds wetted with a polymeric water-based fluid released clusters of particles when external forces overcame the bonding forces and the beds started to break up. Similarly, it was observed that an oil-based fluid wetted bed allowed particles to break free as single particles. These findings may explain the observed differences in previous cutting transport studies.

Annular Frictional Pressure Losses During Drilling—Predicting the Effect of Drillstring Rotation

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Arild Saasen
Keyword(s):  
Rheological Properties ◽  
Pressure Loss ◽  
Drilling Fluid ◽  
Axial Flow ◽  
Drilling Fluids ◽  
Unstable Flow ◽  
Pressure Losses ◽  
Shear Dependent Viscosity ◽  
Water Based ◽  
Dependent Viscosity

Controlling the annular frictional pressure losses is important in order to drill safely with overpressure without fracturing the formation. To predict these pressure losses, however, is not straightforward. First of all, the pressure losses depend on the annulus eccentricity. Moving the drillstring to the wall generates a wider flow channel in part of the annulus which reduces the frictional pressure losses significantly. The drillstring motion itself also affects the pressure loss significantly. The drillstring rotation, even for fairly small rotation rates, creates unstable flow and sometimes turbulence in the annulus even without axial flow. Transversal motion of the drillstring creates vortices that destabilize the flow. Consequently, the annular frictional pressure loss is increased even though the drilling fluid becomes thinner because of added shear rate. Naturally, the rheological properties of the drilling fluid play an important role. These rheological properties include more properties than the viscosity as measured by API procedures. It is impossible to use the same frictional pressure loss model for water based and oil based drilling fluids even if their viscosity profile is equal because of the different ways these fluids build viscosity. Water based drilling fluids are normally constructed as a polymer solution while the oil based are combinations of emulsions and dispersions. Furthermore, within both water based and oil based drilling fluids there are functional differences. These differences may be sufficiently large to require different models for two water based drilling fluids built with different types of polymers. In addition to these phenomena washouts and tool joints will create localised pressure losses. These localised pressure losses will again be coupled with the rheological properties of the drilling fluids. In this paper, all the above mentioned phenomena and their consequences for annular pressure losses will be discussed in detail. North Sea field data is used as an example. It is not straightforward to build general annular pressure loss models. This argument is based on flow stability analysis and the consequences of using drilling fluids with different rheological properties. These different rheological properties include shear dependent viscosity, elongational viscosity and other viscoelastic properties.

Low ECD High Performance Invert Emulsion Drilling Fluids: Lab Development and Field Deployment

2021 ◽  
Author(s):  
Vikrant Wagle ◽  
Abdullah Yami ◽  
Michael Onoriode ◽  
Jacques Butcher ◽  
Nivika Gupta
Keyword(s):  
High Performance ◽  
Filter Cake ◽  
Drilling Fluid ◽  
Field Performance ◽  
Superior Performance ◽  
Core Material ◽  
Drilling Fluids ◽  
Invert Emulsion ◽  
Field Deployment ◽  
Permeability Studies

Abstract The present paper describes the results of the formulation of an acid-soluble low ECD organoclay-free invert emulsion drilling fluid formulated with acid soluble manganese tetroxide and a specially designed bridging package. The paper also presents a short summary of field applications to date. The novel, non-damaging fluid has superior rheology resulting in lower ECD, excellent suspension properties for effective hole cleaning and barite-sag resistance while also reducing the risk of stuck pipe in high over balance applications. 95pcf high performance invert emulsion fluid (HPIEF) was formulated using an engineered bridging package comprising of acid-soluble bridging agents and an acid-soluble weighting agent viz. manganese tetroxide. The paper describes the filtration and rheological properties of the HPIEF after hot rolling at 300oF. Different tests such as contamination testing, sag-factor analysis, high temperature-high pressure rheology measurements and filter-cake breaking studies at 300oF were performed on the HPIEF. The 95pcf fluid was also subjected to particle plugging experiments to determine the invasion characteristics and the non-damaging nature of the fluids. The 95pcf HPIEF exhibited optimal filtration properties at high overbalance conditions. The low PV values and rheological profile support low ECDs while drilling. The static aging tests performed on the 95pcf HPIEF resulted in a sag factor of less than 0.53, qualifying the inherent stability for expected downhole conditions. The HPIEF demonstrated resilience to contamination testing with negligible change in properties. Filter-cake breaking experiments performed using a specially designed breaker fluid system gave high filter-cake breaking efficiency. Return permeability studies were performed with the HPIEF against synthetic core material, results of which confirmed the non-damaging design of the fluid. The paper thus demonstrates the superior performance of the HPIEF in achieving the desired lab and field performance.

ENVIRONMENTAL DRILLING SOLUTIONS ON THE POLYMERIC BASIS

2020 ◽  
Author(s):  
E.A. Flik ◽  
◽  
Y.E. Kolodyazhnaya
Keyword(s):  
Oil And Gas ◽  
Drilling Fluid ◽  
Oil And Gas Industry ◽  
Environmental Safety ◽  
Drilling Fluids ◽  
Gas Industry ◽  
Fluid Systems ◽  
Water Based

The article assesses the environmental safety of drilling fluids that are currently widely used in the oil and gas industry. It shows active development of water-based drilling fluid systems using xanthan biopolymer.

Full Scale Flow Loop Experiments of Hole Cleaning Performances of Drilling Fluids

2015 ◽  
Author(s):  
Jan David Ytrehus ◽  
Ali Taghipour ◽  
Sneha Sayindla ◽  
Bjørnar Lund ◽  
Benjamin Werner ◽  
...  
Keyword(s):  
Test Section ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Flow Loop ◽  
Base Oil ◽  
Hole Cleaning ◽  
Cleaning Performance ◽  
Water Based ◽  
Fluid Properties ◽  
Drilling Cost

One important requirement for a drilling fluid is the ability to transport the cuttings out of the borehole. Improved hole cleaning is a key to solve several challenges in the drilling industry and will allow both longer wells and improved quality of well construction. It has been observed, however, that drilling fluids with similar properties according to the API standard can have significantly different behavior with respect to hole cleaning performance. The reasons for this are not fully understood. This paper presents results from flow loop laboratory tests without and with injected cuttings size particles using a base oil and a commercial oil based drilling fluid. The results demonstrate the importance of the rheological properties of the fluids for the hole cleaning performance. A thorough investigation of the viscoelastic properties of the fluids was performed with a Fann viscometer and a Paar-Physica rheometer, and was used to interpret the results from the flow loop experiments. Improved understanding of the fluid properties relevant to hole cleaning performance will help develop better models of wellbore hydraulics used in planning of well operations. Eventually this may lead to higher ROP with water based drilling fluids as obtained with oil based drilling fluids. This may ease cuttings handling in many operations and thereby significantly reduce the drilling cost using (normally) more environmentally friendly fluids. The experiments have been conducted as part of an industry-sponsored research project where understanding the hole cleaning performance of various oil and water based drilling fluids is the aim. The experiments have been performed under realistic conditions. The flow loop includes a 10 meter long test section with 2″ OD freely rotating drillstring inside a 4″ ID wellbore made of concrete. Sand particles were injected while circulating the drilling fluid through the test section in horizontal position.

Sign in / Sign up

Export Citation Format

Share Document