scholarly journals Development of an Integrated Power Distribution System Laboratory Platform Using Modular Miniature Physical Elements: A Case Study of Fault Location

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3780 ◽  
Author(s):  
Jinrui Tang ◽  
Binyu Xiong ◽  
Chen Yang ◽  
Cuilan Tang ◽  
Yang Li ◽  
...  
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Fault Location ◽  
Renewable Energy Sources ◽  
Distribution Networks ◽  
Power Distribution System ◽  
Zero Sequence ◽  
Assembly Technology ◽  
Physical Elements

The main shortcomings of the software-based power engineering education are a lack of physical understanding of phenomena and hands-on experience. Existing scaled-down analogous educational power system platforms cannot be widely used for experiments in universities due to the high cost, complicated operation, and huge size. An integrated power distribution system laboratory platform (PDSLP) using modular miniature physical elements is proposed in this paper. The printed circuit board (PCB) and microelectronic technology are proposed to construct each physical element. Furthermore, the constructed physical elements are used to set up an integrated PDSLP based on modular assembly technology. The size of the proposed cost-efficient PDSLP is significantly reduced, and the reliability of the proposed PDSLP can be improved greatly because the signal transmission path is shortened and a number of welding points are reduced. A PDSLP for fault location in neutral non-effectively grounded distribution systems (NGDSs) is selected as a typical experimental scenario and one scaled-down distribution network with three feeders is subsequently implemented and discussed. The measured zero-sequence currents by our proposed PDSLP when a single-phase earth fault occurred can reveal the true features of the fault-generated signals, including steady-state and transient characteristics of zero-sequence currents. They can be readily observed and used for students to design corresponding fault location algorithms. Modular renewable energy sources and other elements can be designed, implemented and integrated into the proposed platform for the laboratory education of the active distribution networks in the future.

scholarly journals Complete power distribution system representation and state determination for fault location

DYNA ◽  
2015 ◽  
Vol 82 (192) ◽  
pp. 141-149 ◽  
Author(s):  
Andres Felipe Panesso-Hernández ◽  
Juan Mora-Flórez ◽  
Sandra Pérez-Londoño
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Fault Location ◽  
Estimation Error ◽  
Distance Estimation ◽  
Power Distribution Systems ◽  
Line Load ◽  
Power Distribution System ◽  
Line Section

<p>The impedance-based approaches for fault location in power distribution systems determine a faulted line section. Next, these require of the estimation of the voltages and currents at one or both section line ends to exactly determine the fault location. It is a challenge because in most of the power distribution systems, measurements are only available at the main substation.  This document presents a modeling proposal of the power distribution system and an easy implementation method to estimate the voltages and currents at the faulted line section, using the measurements at the main substation, the line, load, transformer parameters and other serial and shunt connected devices and the power system topology. The approach here proposed is tested using a fault locator based on superimposed components, where the distance estimation error is lower than 1.5% in all of the cases. </p>

Planning of Distribution System with High Penetration Level for Distributed Generation in Smart Grid

2018 ◽  
Vol 8 (3) ◽  
Author(s):  
Reza Tajik
Keyword(s):  
Smart Grid ◽  
Power Systems ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Distribution Networks ◽  
Planning Problem ◽  
Renewable Energy Resources ◽  
Power Distribution System ◽  
High Penetration

Nowadays, the utilization of renewable energy resources in distribution systems (DSs) has been rapidly increased. Since distribution generation (DG) use renewable resources (i.e., biomass, wind and solar) are emerging as proper solutions for electricity generation. Regarding the tremendous deployment of DG, common distribution networks are undergoing a transition to DSs, and the common planning methods have become traditional in the high penetration level. Indeed, in conformity with the voltage violation challenge of these resources, this problem must be dealt with too. So, due to the high penetration of DG resources and nonlinear nature of most industrial loads, the planning of DG installation has become an important issue in power systems. The goal of this paper is to determine the planning of DG in distribution systems through smart grid to minimize losses and control grid factors. In this regard, the present work intending to propose a suitable method for the planning of DSs, the key properties of DS planning problem are evaluated from the various aspects, such as the allocation of DGs, and planning, and high-level uncertainties. Also depending on these analyses, this universal literature review addressed the updated study associated with DS planning. In this work, an operational design has been prepared for a higher performance of the power distribution system in the presence of DG. Artificial neural network (ANN) has been used as a method for voltage monitoring and generation output optimization. The findings of the study show that the proposed method can be utilized as a technique to improve the process of the distribution system under various penetration levels and in the presence of DG. Also, the findings revealed that the optimal use of ANN method leads to more controllable and apparent DS.

scholarly journals Technological Perspective of Cyber Secure Smart Inverters Used in Power Distribution System: State of the Art Review

2021 ◽  
Vol 11 (18) ◽  
pp. 8780
Author(s):  
Sumukh Surya ◽  
Mohan Krishna Srinivasan ◽  
Sheldon Williamson
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Renewable Energy Sources ◽  
Cyber Attacks ◽  
Critical Examination ◽  
Power Distribution System ◽  
Safety Issues ◽  
Smart Inverters ◽  
Technological Perspective

The purpose of smart grid architecture as compared to the conventional grid is to ensure more stability, reliability and bi-directional communication between the utility and the consumer. The deployment of the same has succeeded in improving the efficiency of the distribution systems and effective co-ordination and interoperability among the different components of the grid. Smart inverters play a major role in seamless grid integration, control and conversion of power when the renewable energy sources are present. However, they come with several security challenges as well, which are of considerable concern. Certain cyber threats include physical and cyber attacks, natural phenomena which in turn can lead to grid failure, blackouts, commercial energy losses, privacy and safety issues, etc. Therefore, there is a need for critical examination of all these issues which must be considered for designing cyber secure smart inverters at the distribution level. In this comprehensive review, keeping the technological perspective in mind, the existing gaps and the necessity for the same are highlighted. The various topologies, IEEE protocols and the control strategy are presented in detail. This will enable prospective researchers to address the design issues of smart inverters with greater focus on security and reliability aspects.

scholarly journals Simulation Study of Power Management for a Highly Reliable Distribution System using a Triple Active Bridge Converter in a DC Microgrid

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3178 ◽  
Author(s):  
Yue Yu ◽  
Keiji Wada
Keyword(s):  
Power Management ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Data Centers ◽  
High Reliability ◽  
Renewable Energy Sources ◽  
Management Approach ◽  
Dc Microgrid ◽  
Power Distribution System

Owing to the acute energy shortage issue and the increasing energy demands of information and communication technology systems worldwide, the development of a DC microgrid that can utilize renewable energy sources, such as wind and photovoltaic power, has been accelerated. Therefore, power management for DC microgrid distributed systems is promoted to achieve high reliability and efficiency in power distribution systems. For industry and power transmission applications such as data centers, power management with the help of DC converters is highly recommended. In this paper, we propose a prototype of a power distribution system with a triple active bridge (TAB) converter for data centers in the DC microgrid. Moreover, we introduce a power management approach for a distribution system using the TAB converter. Finally, we perform simulations of the proposed configuration to verify the controllability of the circuit performance and the high reliability of the system.

scholarly journals Application of PSO for optimal coordination of directional over-current relays in distribution system with distributed renewable energy sources

2021 ◽  
Vol 10 (2) ◽  
pp. 188
Author(s):  
Lazhar Bougouffa ◽  
Abdelaziz Chaghi
Keyword(s):  
Renewable Energy ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Renewable Energy Sources ◽  
Electrical Power ◽  
Distribution Networks ◽  
Electrical Network ◽  
Energy Sources ◽  
Optimal Coordination

<p>The use of Distributed Renewable Energy Sources in the electrical network has expanded greatly. But, integration of these resources into distribution systems caused more problems in protection related issues such as mis-coordination, and changes the direction and value of fault currents. When connecting new D-RES to electrical power distribution networks, it is required to re-coordinate Directional Over-CurrentRelays (DOC-Relays) to ensure the continuity of the power transmission when the short circuits take place. This work presented a Particle Swarm Optimization (PSO) algorithm to determine two independent variables called Pickup current (Ip) and Time Dial Setting (TDS) for optimal setting of relays. From analysis result, the impacts of RES location in the distribution system on DOCRs had been observed on the optimal relays settings</p>

scholarly journals Augmentation of situational awareness by fault passage indicators in distribution network incorporating network reconfiguration

2019 ◽  
Vol 4 (1) ◽  
Author(s):  
Tanmay Jain ◽  
Debomita Ghosh ◽  
Dusmanta Kumar Mohanta
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Fault Location ◽  
Situational Awareness ◽  
Electronic Device ◽  
Distribution Networks ◽  
System Stability ◽  
System Integrity ◽  
Intelligent Electronic Device

AbstractPower distribution systems are profoundly inclined to disturbances like untimely switching of breakers & relays, sympathetic tripping, and uncertainties regarding fault location. Thus, system stability and reliability are greatly affected. In this way, situational awareness and system integrity are the crucial factors in developing power system security, as it empowers successful decision making & timely reaction by the operators to any disturbance and also maintaining continuity of power supply. This paper focuses on the enhancement of situational awareness by fault location through fault passage indicators (FPI) to improve nominal impedance-based methods in distribution networks. Also, the proposed method is validated by comparing it with Intelligent Electronic Device (IED) based fault location method. Further, simultaneous reconfiguration of the system is incorporated to maintain the continuity of supply. The analysis has been tested on IEEE 33 bus distribution system.

scholarly journals Configurations of Aromatic Networks for Power Distribution System

2020 ◽  
Vol 12 (10) ◽  
pp. 4317
Author(s):  
K. Prakash ◽  
F. R. Islam ◽  
K. A. Mamun ◽  
H. R. Pota
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Smart Grids ◽  
Sustainable Energy ◽  
Distribution Network ◽  
Geographical Location ◽  
Distribution Networks ◽  
Self Healing ◽  
Power Distribution System ◽  
Improve Energy Efficiency

A distribution network is one of the main parts of a power system that distributes power to customers. While there are various types of power distribution networks, a recently introduced novel structure of an aromatic network could begin a new era in the distribution levels of power systems and designs of microgrids or smart grids. In order to minimize blackout periods during natural disasters and provide sustainable energy, improve energy efficiency and maintain stability of a distribution network, it is essential to configure/reconfigure the network topology based on its geographical location and power demand, and also important to realize its self-healing function. In this paper, a strategy for reconfiguring aromatic networks based on structures of natural aromatic molecules is explained. Various network structures are designed, and simulations have been conducted to justify the performance of each configuration. It is found that an aromatic network does not need to be fixed in a specific configuration (i.e., a DDT structure), which provides flexibility in designing networks and demonstrates that the successful use of such structures will be a perfect solution for both distribution networks and microgrid systems in providing sustainable energy to the end users.

scholarly journals FCM and Statistical Based Approach for Classification and Location of Faults in Electrical Distribution System

2011 ◽  
pp. 64-68
Author(s):  
Pratul Arvind ◽  
Rudra prakash Maheswari
Keyword(s):  
Expectation Maximization ◽  
Power Distribution ◽  
Distribution System ◽  
Fault Location ◽  
Electrical Power ◽  
Electrical Power System ◽  
Power Distribution System ◽  
Electric Power Distribution ◽  
Node Distribution ◽  
System Restoration

Electric Power Distribution System is a complex network of electrical power system. Also, large number of lines on a distribution system experiences regular faults which lead to high value of current. Speedy and precise fault location plays a pivotal role in accelerating system restoration which is a need of modern day. Unlike transmission system which involves a simple connection, distribution system has a very complicated structure thereby making it a herculean task to design the network for computational analysis. In this paper, the authors have simulated IEEE 13- node distribution system using PSCAD which is an unbalanced system and current samples are generated at the substation end. A Fuzzy c-mean (FCM) and statistical based approach has been used. Samples are transformed as clusters by use of FCM and fed to Expectation- Maximization (EM) algorithm for classifying and locating faults in an unbalanced distribution system. Further, it is to be kept in mind that the combination has not been used for the above purpose as per the literature available till date.

scholarly journals Active Reduction of Short-Circuit Current in Power Distribution Systems

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 334
Author(s):  
Esteban Pulido ◽  
Luis Morán ◽  
Felipe Villarroel ◽  
José Silva
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Short Circuit ◽  
Circuit Breaker ◽  
Short Circuit Current ◽  
Power Converter ◽  
Power Distribution Systems ◽  
Power Distribution System ◽  
In Series

In this paper, a new concept of short-circuit current (SCC) reduction for power distribution systems is presented and analyzed. Conventional fault current limiters (FCLs) are connected in series with a circuit breaker (CB) that is required to limit the short-circuit current. Instead, the proposed scheme consisted of the parallel connection of a current-controlled power converter to the same bus intended to reduce the amplitude of the short-circuit current. This power converter was controlled to absorb a percentage of the short-circuit current from the bus to reduce the amplitude of the short-circuit current. The proposed active short-circuit current reduction scheme was implemented with a cascaded H-bridge power converter and tested by simulation in a 13.2 kV industrial power distribution system for three-phase faults, showing the effectiveness of the short-circuit current attenuation in reducing the maximum current requirement in all circuit breakers connected to the same bus. The paper also presents the design characteristics of the power converter and its associated control scheme.

scholarly journals Flexibility Enhancement in an Islanded Distribution Power System by Online Demand-Side Management

2019 ◽  
Vol 217 ◽  
pp. 01020 ◽  
Author(s):  
Margarita Chulyukova ◽  
Nikolai Voropai
Keyword(s):  
Power System ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Load Shedding ◽  
Load Management ◽  
Daily Maximum ◽  
Power Distribution Systems ◽  
Power Distribution System ◽  
Islanded Operation

The paper considers the possibilities of increasing the flexibility of power distribution systems by real-time load management. The principles of the implementation of special automatic systems for this purpose are proposed. These systems enable some loads of specific consumers of the power distribution system switched to islanded operation to “shift” from the daily maximum to the minimum, which makes some generators available to connect certain essential consumers disconnected earlier by under-frequency load shedding system to the power system. The approach under consideration is illustrated by a power system with distributed generation.

Sign in / Sign up

Export Citation Format

Share Document