scholarly journals Performance Analysis of TiO2-Modified Co/MgAl2O4 Catalyst for Dry Reforming of Methane in a Fixed Bed Reactor for Syngas (H2, CO) Production

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3347
Author(s):  
Arslan Mazhar ◽  
Asif Hussain Khoja ◽  
Abul Kalam Azad ◽  
Faisal Mushtaq ◽  
Salman Raza Naqvi ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Fixed Bed ◽  
Catalytic Performance ◽  
Dry Reforming ◽  
Fixed Bed Reactor ◽  
Dry Reforming Of Methane ◽  
Catalyst Stability ◽  
Feed Ratio ◽  
Catalyst Loading ◽  
Impregnation Method

Co/TiO2–MgAl2O4 was investigated in a fixed bed reactor for the dry reforming of methane (DRM) process. Co/TiO2–MgAl2O4 was prepared by modified co-precipitation, followed by the hydrothermal method. The active metal Co was loaded via the wetness impregnation method. The prepared catalyst was characterized by XRD, SEM, TGA, and FTIR. The performance of Co/TiO2–MgAl2O4 for the DRM process was investigated in a reactor with a temperature of 750 °C, a feed ratio (CO2/CH4) of 1, a catalyst loading of 0.5 g, and a feed flow rate of 20 mL min−1. The effect of support interaction with metal and the composite were studied for catalytic activity, the composite showing significantly improved results. Moreover, among the tested Co loadings, 5 wt% Co over the TiO2–MgAl2O4 composite shows the best catalytic performance. The 5%Co/TiO2–MgAl2O4 improved the CH4 and CO2 conversion by up to 70% and 80%, respectively, while the selectivity of H2 and CO improved to 43% and 46.5%, respectively. The achieved H2/CO ratio of 0.9 was due to the excess amount of CO produced because of the higher conversion rate of CO2 and the surface carbon reaction with oxygen species. Furthermore, in a time on stream (TOS) test, the catalyst exhibited 75 h of stability with significant catalytic activity. Catalyst potential lies in catalyst stability and performance results, thus encouraging the further investigation and use of the catalyst for the long-run DRM process.

scholarly journals Production of CO-rich Hydrogen Gas from Methane Dry Reforming over Co/CeO2 Catalyst

2016 ◽  
Vol 11 (2) ◽  
pp. 210 ◽  
Author(s):  
Bamidele V. Ayodele ◽  
Maksudur R. Khan ◽  
Chin Kui Cheng
Keyword(s):  
Catalytic Activity ◽  
Fixed Bed ◽  
Dry Reforming ◽  
Hydrogen Gas ◽  
Fixed Bed Reactor ◽  
Feed Ratio ◽  
X Ray Diffraction ◽  
Methane Dry Reforming ◽  
X Ray ◽  
Adsorption Desorption

<p>Production of CO-rich hydrogen gas from methane dry reforming was investigated over CeO<sub>2</sub>-supported Co catalyst. The catalyst was synthesized by wet impregnation and subsequently characterized by field emission scanning electron microscope (FESEM), energy dispersion X-ray spectroscopy (EDX), liquid N<sub>2</sub> adsorption-desorption, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) for the structure, surface and thermal properties. The catalytic activity test of the Co/CeO<sub>2</sub> was investigated between 923-1023 K under reaction conditions in a stainless steel fixed bed reactor. The composition of the products (CO<sub>2</sub> and H<sub>2</sub>) from the methane dry reforming reaction was measured by gas chromatography (GC) coupled with thermal conductivity detector (TCD). The effects of feed ratios and reaction temperatures were investigated on the catalytic activity toward product selectivity, yield, and syngas ratio. Significantly, the selectivity and yield of both H<sub>2</sub> and CO increases with feed ratio and temperature. However, the catalyst shows higher activity towards CO selectivity. The highest H<sub>2</sub> and CO selectivity of 19.56% and 20.95% respectively were obtained at 1023 K while the highest yield of 41.98% and 38.05% were recorded for H<sub>2</sub> and CO under the same condition. Copyright © 2016 BCREC GROUP. All rights reserved</p><p><em>Received: 21<sup>st</sup> January 2016; Revised: 23<sup>rd</sup> February 2016; Accepted: 23<sup>rd</sup> February 2016</em></p><p><strong>How to Cite:</strong> Ayodele, B.V., Khan, M.R., Cheng, C. K. (2016). Production of CO-rich Hydrogen Gas from Methane Dry Reforming over Co/CeO<sub>2</sub> Catalyst. <em>Bulletin of Chemical Reaction Engineering &amp; Catalysi</em>s, 11 (2): 210-219 (doi:10.9767/bcrec.11.2.552.210-219)</p><p><strong>Permalink/DOI:</strong> http://dx.doi.org/10.9767/bcrec.11.2.552.210-219</p>

scholarly journals Catalytic Performance of Metal Oxides Promoted Nickel Catalysts Supported on Mesoporous γ-Alumina in Dry Reforming of Methane

Processes ◽  
2020 ◽  
Vol 8 (5) ◽  
pp. 522
Author(s):  
Anis H. Fakeeha ◽  
Abdulaziz A. Bagabas ◽  
Mahmud S. Lanre ◽  
Ahmed I. Osman ◽  
Samsudeen O. Kasim ◽  
...  
Keyword(s):  
Metal Oxides ◽  
Nickel Catalysts ◽  
Catalytic Performance ◽  
Dry Reforming ◽  
Coke Deposition ◽  
Dry Reforming Of Methane ◽  
Catalyst Stability ◽  
Incipient Wetness Impregnation ◽  
Impregnation Method ◽  
Ni Catalysts

Dry reforming of CH4 was conducted over promoted Ni catalysts, supported on mesoporous gamma-alumina. The Ni catalysts were promoted by various metal oxides (CuO, ZnO, Ga2O3, or Gd2O3) and were synthesized by the incipient wetness impregnation method. The influence of the promoters on the catalyst stability, coke deposition, and H2/CO mole ratio was investigated. Stability tests were carried out for 460 min. The H2 yield was 87% over 5Ni+1Gd/Al, while the CH4 and CO2 conversions were found to decrease in the following order: 5Ni+1Gd/Al > 5Ni+1Ga/Al > 5Ni+1Zn/Al > 5Ni/Al > 5Ni+1Cu/Al. The high catalytic performance of 5Ni+1Gd/Al, 5Ni+1Ga/Al, and 5Ni+1Zn/Al was found to be closely related to their contents of NiO species, which interacted moderately and strongly with the support, whereas free NiO in 5Ni+1Cu/Al made it catalytically inactive, even than 5Ni/Al. The 5Ni+1Gd/Al catalyst showed the highest CH4 conversion of 83% with H2/CO mole ratio of ~1.0.

CO2 valorization into synthetic natural gas (SNG) using a Co–Ni bimetallic Y2O3 based catalysts

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Radwa A. El-Salamony ◽  
Sara A. El-Sharaky ◽  
Seham A. Al-Temtamy ◽  
Ahmed M. Al-Sabagh ◽  
Hamada M. Killa
Keyword(s):  
Reaction Mechanism ◽  
Natural Gas ◽  
Fixed Bed ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Molar Ratio ◽  
Impregnation Method ◽  
Synthetic Natural Gas ◽  
Methanation Reaction ◽  
Co2 Valorization

Abstract Recently, because of the increasing demand for natural gas and the reduction of greenhouse gases, interests have focused on producing synthetic natural gas (SNG), which is suggested as an important future energy carrier. Hydrogenation of CO2, the so-called methanation reaction, is a suitable technique for the fixation of CO2. Nickel supported on yttrium oxide and promoted with cobalt were prepared by the wet-impregnation method respectively and characterized using SBET, XRD, FTIR, XPS, TPR, and HRTEM/EDX. CO2 hydrogenation over the Ni/Y2O3 catalyst was examined and compared with Co–Ni/Y2O3 catalysts, Co% = 10 and 15 wt/wt. The catalytic test was conducted with the use of a fixed-bed reactor under atmospheric pressure. The catalytic performance temperature was 350 °C with a supply of H2:CO2 molar ratio of 4 and a total flow rate of 200 mL/min. The CH4 yield was reached 67%, and CO2 conversion extended 48.5% with CO traces over 10Co–Ni/Y2O3 catalyst. This encourages the direct methanation reaction mechanism. However, the reaction mechanism over Ni/Y2O3 catalyst shows different behaviors rather than that over bi-metal catalysts, whereas the steam reforming of methane reaction was arisen associated with methane consumption besides increase in H2 and CO formation; at the same temperature reaction.

scholarly journals Effect of CO2 partial pressure on dry reforming of ethanol for hydrogen production

2018 ◽  
Vol 1 (1) ◽  
pp. 6-10
Author(s):  
Fahim Fayaz ◽  
Ahmad Ziad Sulaiman ◽  
Sharanjit Singh ◽  
Sweeta Akbari
Keyword(s):  
Partial Pressure ◽  
Fixed Bed ◽  
Dry Reforming ◽  
Fixed Bed Reactor ◽  
Bet Surface Area ◽  
Impregnation Method ◽  
X Ray Diffraction ◽  
Co2 Partial Pressure ◽  
Temperature Programmed ◽  
Al2o3 Catalyst

The effect of CO2 partial pressure on ethanol dry reforming was evaluated over 5%Ce-10%Co/Al2O3 catalyst at = PCO2 = 20-50 kPa, PC2H5OH = 20 kPa, reaction temperature of 973 K under atmospheric pressure. The catalyst was prepared by using impregnation method and tested in a fixed-bed reactor. X-ray diffraction measurements studied the formation of Co3O4, spinel CoAl2O4 and CeO2, phases on surface of 5%Ce-10%Co/Al2O3 catalyst. CeO2, CoO and Co3O4 oxides were obtained during temperature–programmed calcination. Ce-promoted 10%Co/Al2O3 catalyst possessed high BET surface area of 137.35 m2 g-1. C2H5OH and CO2 conversions was improved with increasing CO2 partial pressure from 20-50 kPa whilst the optimal selectivity of H2 and CO was achieved at 50 kPa.

Research on the Catalytic Activity of MnyCezOx/TiO2 for Ethyl Acetate Oxidation

2013 ◽  
Vol 781-784 ◽  
pp. 308-311 ◽  
Author(s):  
Xin Li ◽  
Wei Su ◽  
Qi Bin Xia ◽  
Zhi Meng Liu
Keyword(s):  
Catalytic Activity ◽  
Ethyl Acetate ◽  
High Activity ◽  
Fixed Bed ◽  
Space Velocity ◽  
Fixed Bed Reactor ◽  
Impregnation Method ◽  
Acetate Oxidation ◽  
Acetate Concentration ◽  
Molar Ratios

Manganese and cerium based catalysts with different Mn/Ce molar ratios prepared by impregnation method for ethyl acetate oxidation. The activity tests of the samples were performed in a fixed-bed reactor. The effect of gas hourly space velocity (GHSV) and ethyl acetate concentration on the catalytic activity of the catalyst were also investigated. The results showed that these catalysts had high activity for the catalytic oxidation of ethyl acetate, of which the catalyst Mn0.9Ce0.1Ox/TiO2exhibitedthe bestactivity, and the temperature required for 90% conversion of ethyl acetate was at 216 °C. The catalyst Mn0.9Ce0.1Ox/TiO2still maintained high activity in the range of GHSV (16,500 to 48,500 h-1) and ethyl acetate concentration (4526 to 7092 mg/m3). In additional, experiments for measuring stability of Mn0.9Ce0.1Ox/TiO2were carried out, and experimental results showed that the good stability of Mn0.9Ce0.1Ox/TiO2was kept after it has run for 25 hours.

Effect of Ni/Co Ratio on Bimetallic Oxide Supported Silica Catalyst in CO2 Methanation

2015 ◽  
Vol 802 ◽  
pp. 431-436
Author(s):  
Siti Aminah Md Ali ◽  
Ku Halim Ku Hamid ◽  
Kamariah Noor Ismail
Keyword(s):  
Catalytic Activity ◽  
Fixed Bed ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Wet Impregnation ◽  
Co Precipitation

Five series of silica supported bimetallic oxide (NiCo/SiO2) catalysts have been synthesized through successive reverse co-precipitation and wet impregnation methods at different metal loadings (i.e. 80Ni20Co/SiO2,, 60Ni40Co/SiO2,50Ni50Co/SiO2,40Ni60Co/SiO2,20Ni80Co/SiO2). The catalytic performance of these catalysts were tested for the CO2methanation catalysis using microactivity fixed bed reactor. Nickel rich catalyst (80Ni20Co/SiO2) exhibited the highest catalytic activity in the CO2methanation with 47.1% of CO2conversion. Meanwhile, the CH4selectivity and yield was found to be at 99.9% and 27%, respectively.

scholarly journals Effect of Preparation Method on ZrO2-Based Catalysts Performance for Isobutanol Synthesis from Syngas

Catalysts ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 752 ◽  
Author(s):  
Yingquan Wu ◽  
Li Tan ◽  
Tao Zhang ◽  
Hongjuan Xie ◽  
Guohui Yang ◽  
...  
Keyword(s):  
Fixed Bed ◽  
Carbon Chain ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Chain Growth ◽  
Impregnation Method ◽  
Surface Areas ◽  
Co Precipitation ◽  
Diffuse Reflectance Infrared

Two types of amorphous ZrO2 (am-ZrO2) catalysts were prepared by different co-precipitation/reflux digestion methods (with ethylenediamine and ammonia as the precipitant respectively). Then, copper and potassium were introduced for modifying ZrO2 via an impregnation method to enhance the catalytic performance. The obtained catalysts were further characterized by means of Brunauer-Emmett-Teller surface areas (BET), X-ray diffraction (XRD), H2-temperature-programmed reduction (H2-TPR), and In situ diffuse reflectance infrared spectroscopy (in situ DRIFTS). CO hydrogenation experiments were performed in a fixed-bed reactor for isobutanol synthesis. Great differences were observed on the distribution of alcohols over the two types of ZrO2 catalysts, which were promoted with the same content of Cu and K. The selectivity of isobutanol on K-CuZrO2 (ammonia as precipitant, A-KCZ) was three times higher than that on K-CuZrO2 (ethylenediamine as precipitant, E-KCZ). The characterization results indicated that the A-KCZ catalyst supplied more active hydroxyls (isolated hydroxyls) for anchoring and dispersing Cu. More importantly, it was found that bicarbonate species were formed, which were ascribed as important C1 species for isobutanol formation on the A-KCZ catalyst surface. These C1 intermediates had relatively stronger adsorption strength than those adsorbed on the E-KCZ catalyst, indicating that the bicarbonate species on the A-KCZ catalyst had a longer residence time for further carbon chain growth. Therefore, the selectivity of isobutanol was greatly enhanced. These findings would extend the horizontal of direct alcohols synthesis from syngas.

Methane Dry Reforming over Ni-Co/Al2O3: Kinetic Modelling in a Catalytic Fixed-bed Reactor

2017 ◽  
Vol 15 (6) ◽  
Author(s):  
Yacine Benguerba ◽  
Mirella Virginie ◽  
Christine Dumas ◽  
Barbara Ernst
Keyword(s):  
Catalyst Deactivation ◽  
Kinetic Modelling ◽  
Fixed Bed ◽  
Dry Reforming ◽  
Fixed Bed Reactor ◽  
Coke Deposition ◽  
Dry Reforming Of Methane ◽  
Reactor Model ◽  
Reverse Water Gas Shift ◽  
Different Temperatures

Abstract The dry reforming of CH4 was investigated in a catalytic fixed-bed reactor to produce hydrogen at different temperatures over supported bimetallic Ni-Co catalyst. The reactor model for the dry reforming of methane used a set of kinetic models: The Zhang et al model for the dry reforming of methane (DRM); the Richardson-Paripatyadar model for the reverse water gas shift (RWGS); and the Snoeck et al kinetics for the coke-deposition and gasification reactions. The effect of temperatures on the performance of the reactor was studied. The amount of each species consumed or/and produced were calculated and compared with the experimental determined ones. It was showed that the set of kinetic model used in this work gave a good fit and accurately predict the experimental observed profiles from the fixed bed reactor. It was found that reaction-4 and reaction-5 could be neglected which could explain the fact that this catalyst coked rapidly comparatively with other catalyst. The use of large amount of Ni-Co will lead to carbon deposition and so to the catalyst deactivation.

Lanthanum Modified Catalyst for Efficient Supply of Hydrogen through Dehydrogenation of Organic Chemical Hydrides

2011 ◽  
Vol 287-290 ◽  
pp. 2110-2115
Author(s):  
Gang Li Zhu ◽  
Tao Chen ◽  
Xue Dong Jiang ◽  
Hai Liang Zhang ◽  
Bo Lun Yang
Keyword(s):  
Energy Dispersive Spectrometer ◽  
Fixed Bed ◽  
Textural Properties ◽  
Nitrogen Adsorption ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Metal Species ◽  
Organic Chemical ◽  
Impregnation Method ◽  
Active Components

Dehydrogenation process of organic chemical hydrides was improved by modifying the catalyst of nickel-activated carbon (Ni/AC) with lanthanum (La). The catalysts were prepared in impregnation method with different amounts of La and Ni. The textural properties and morphology of catalyst were analyzed by nitrogen adsorption and transmission electron microscope equipped with energy dispersive spectrometer respectively. The effects such as metal content and granule size on the dehydrogenation of cyclohexane were investigated in fixed bed reactor. The results show that the metallic active components can be well dispersed on the support, and the elements analysis indicates the metal species tend to assemble on the surface layer rather than being distributed equally in the whole catalyst. The La modified catalyst LaNi/AC exhibited superior catalytic performance to Ni/AC and the conversion was 45% for LaNi/AC catalyst at 673K, while only 34 % for Ni/AC under the same conditions.

scholarly journals Ni–Cu High-Loaded Sol–Gel Catalysts for Dehydrogenation of Liquid Organic Hydrides: Insights into Structural Features and Relationship with Catalytic Activity

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 2017
Author(s):  
Yuliya Gulyaeva ◽  
Maria Alekseeva (Bykova) ◽  
Olga Bulavchenko ◽  
Anna Kremneva ◽  
Andrey Saraev ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Sol Gel ◽  
Fixed Bed ◽  
Catalytic Performance ◽  
Structural Features ◽  
Atomic Ratio ◽  
Fixed Bed Reactor ◽  
High Catalytic Activity ◽  
Wide Range ◽  
Structure Reactivity Relationship

The heightened interest in liquid organic hydrogen carriers encourages the development of catalysts suitable for multicycle use. To ensure high catalytic activity and selectivity, the structure–reactivity relationship must be extensively investigated. In this study, high-loaded Ni–Cu catalysts were considered for the dehydrogenation of methylcyclohexane. The highest conversion of 85% and toluene selectivity of 70% were achieved at 325 °C in a fixed-bed reactor using a catalyst with a Cu/Ni atomic ratio of 0.23. To shed light on the relationship between the structural features and catalytic performance, the catalysts were thoroughly studied using a wide range of advanced physicochemical tools. The activity and selectivity of the proposed catalysts are related to the uniformity of Cu distribution and its interaction with Ni via the formation of metallic solid solutions. The method of introduction of copper in the catalyst plays a crucial role in the effectiveness of the interaction between the two metals.

Sign in / Sign up

Export Citation Format

Share Document