scholarly journals Assessment of the Environmental Impact of Using Methane Fuels to Supply Internal Combustion Engines

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3356
Author(s):  
Krzysztof Biernat ◽  
Izabela Samson-Bręk ◽  
Zdzisław Chłopek ◽  
Marlena Owczuk ◽  
Anna Matuszewska
Keyword(s):  
Environmental Impact ◽  
Nitrogen Oxide ◽  
Internal Combustion Engines ◽  
Carbon Oxide ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Pollutant Emission ◽  
Combustion Engines

This research paper studied the environmental impact of using methane fuels for supplying internal combustion engines. Methane fuel types and the methods of their use in internal combustion engines were systematized. The knowledge regarding the environmental impact of using methane fuels for supplying internal combustion engines was analyzed. The authors studied the properties of various internal combustion engines used for different applications (specialized engines of power generators—Liebherr G9512 and MAN E3262 LE212, powered by biogas, engine for road and off-road vehicles—Cummins 6C8.3, in self-ignition, original version powered by diesel fuel, and its modified version—a spark-ignition engine powered by methane fuel) under various operating conditions in approval tests. The sensitivity of the engine properties, especially pollutant emissions, to its operating states were studied. In the case of a Cummins 6C8.3 modified engine, a significant reduction in the pollutant emission owing to the use of methane fuel, relative to the original self-ignition engine, was found. The emission of carbon oxide decreased by approximately 30%, hydrocarbons by approximately 70% and nitrogen oxide by approximately 50%, as well as a particulate matter emission was also eliminated. Specific brake emission of carbon oxide is the most sensitive to the operating states of the engine: 0.324 for a self-ignition engine and 0.264 for a spark-ignition engine, with the least sensitive being specific brake emission of nitrogen oxide: 0.121 for a self-ignition engine and 0.097 for a spark-ignition engine. The specific brake emission of carbon monoxide and hydrocarbons for stationary engines was higher in comparison with both versions of Cummins 6C8.3 engine. However, the emission of nitrogen oxide for stationary engines was lower than for Cummins engines.

Thermophysical Properties of Working Substance and Heat Transfer in a Hydrogen Combustion Engine

2003 ◽  
Author(s):  
T. Shudo ◽  
H. Oka
Keyword(s):  
Heat Transfer ◽  
Combustion Chamber ◽  
Heat Loss ◽  
Thermophysical Properties ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Hydrogen Combustion ◽  
Spark Ignition Engine ◽  
Combustion Engines

Hydrogen is a clean alternative to fossil fuels for internal combustion engines and can be easily used in spark-ignition engines. However, the characteristics of the engines fueled with hydrogen are largely different from those with conventional hydrocarbon fuels. A higher burning velocity and a shorter quenching distance for hydrogen as compared with hydrocarbons bring a higher degree of constant volume and a larger heat transfer from the burning gas to the combustion chamber wall of the engines. Because of the large heat loss, the thermal efficiency of an engine fueled with hydrogen is sometimes lower than that with hydrocarbons. Therefore, the analysis and the reduction of the heat loss are crucial for the efficient utilization of hydrogen in internal combustion engines. The empirical correlations to describe the total heat transferred from the burning gas to the combustion chamber walls are often used to calculate the heat loss in internal combustion engines. However, the previous research by one of the authors has shown that the widely used heat transfer correlations cannot be properly applied to the hydrogen combustion even with adjusting the constants in them. For this background, this research analyzes the relationship between characteristics of thermophysical properties of working substance and heat transfer to the wall in a spark-ignition engine fueled with hydrogen.

Development of the Control and Acquisition System for a Natural-Gas Spark-Ignition Engine Test Bench

2019 ◽  
Author(s):  
Lorenzo Gasbarro ◽  
Jinlong Liu ◽  
Christopher Ulishney ◽  
Cosmin E. Dumitrescu ◽  
Luca Ambrogi ◽  
...  
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engines ◽  
Test Bench ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Acquisition System ◽  
Combustion Engines ◽  
Engine Test ◽  
New Sensors

Abstract Investigations using laboratory test benches are the most common way to find the technological solutions that will increase the efficiency of internal combustion engines and curtail their emissions. In addition, the collected experimental data are used by the CFD community to develop engine models that reduce the time-to-market. This paper describes the steps made to increase the reliability of engine experiments performed in a heavy-duty natural-gas spark-ignition engine test-cell such as the design of the control and data acquisition system based on Modbus TCP communication protocol. Specifically, new sensors and a new dynamometer controller were installed. The operation of the improved test bench was investigated at several operating conditions, with data obtained at both high- and low-sampling rates. The results indicated a stable test bench operation.

Behavior Prediction Model in Gas Fueled Spark Ignition Internal Combustion Engines Turbocharged for Genset Application

2013 ◽  
Author(s):  
Jorge Duarte Forero ◽  
German Amador Diaz ◽  
Fabio Blanco Castillo ◽  
Lesme Corredor Martinez ◽  
Ricardo Vasquez Padilla
Keyword(s):  
Equivalence Ratio ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Combustion Engines ◽  
Gaseous Fuels ◽  
Methane Number

In this paper, a mathematical model is performed in order to analyze the effect of the methane number (MN) on knock tendency when spark ignition internal combustion engine operate with gaseous fuels produced from different thermochemical processes. The model was validated with experimental data reported in literature and the results were satisfactory. A general correlation for estimating the autoignition time of gaseous fuels in function of cylinder temperature, and pressure, equivalence ratio and methane number of the fuel was carried out. Livengood and Wu correlation is used to predict autoignition in function of the crank angle. This criterium is a way to predict the autoignition tendency of a fuel/air mixture under engine conditions and consider the ignition delay. A chemical equilibrium model which considers 98 chemical species was used in this research in order to simulate the combustion of the gaseous fuels at differents engine operating conditions. The effect of spark advance, equivalence ratio, methane number (MN), charge (inlet pressure) and inlet temperature (manifold temperature) on engine knocking is evaluated. This work, explore the feasibility of using syngas with low methane number as fuel for commercial internal combustion engines.

Performance evaluation of gasoline alternatives using a thermodynamic spark-ignition engine model

2017 ◽  
Vol 1 (9) ◽  
pp. 1991-2005 ◽  
Author(s):  
Dominik Gschwend ◽  
Patrik Soltic ◽  
Philip Edinger ◽  
Alexander Wokaun ◽  
Frédéric Vogel
Keyword(s):  
Climate Change ◽  
Performance Evaluation ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Engines ◽  
Engine Model ◽  
Surface Transportation

In light of climate change and the fact that surface transportation heavily relies on internal combustion engines, many different alternatives to gasoline have been proposed.

Improvement in Lean Homogenous Spark-Ignition Combustion With Pulsed Energy Spark Plug

2012 ◽  
Author(s):  
Timothy J. Jacobs ◽  
Louis J. Camilli ◽  
Joseph E. Gonnella
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Transfer Efficiency ◽  
Combustion Engines ◽  
Spark Plug ◽  
Lean Mixtures ◽  
Burn Rate

This article describes a study involving new spark plug technology, referred to as pulsed energy spark plug, for use in igniting fuel-air mixtures in a spark ignition internal combustion engine. The study involves precisely controlled constant volume combustion bomb tests. The major defining difference between the pulsed energy spark plug and a conventional spark plug is a peaking capacitor that improves the electrical-to-plasma energy transfer efficiency from a conventional plug’s 1% to the pulsed energy plug’s 50%. Such an increase in transfer efficiency is believed to improve spark energy and subsequently the ignition time and burn rate of a homogeneous, or potentially stratified, fuel-air mixture. The study observes the pulsed energy plug to shorten the ignition delay of both stoichiometric and lean mixtures (with equivalence ratio of 0.8), relative to a conventional spark plug, without increasing the burn rate. Additionally, the pulsed energy plug demonstrates a decreased lean flammability limit that is about 14% lower (0.76 for conventional plug and 0.65 for pulsed energy plug) than that of the conventional spark plug. These features — advanced ignition of stoichiometric and lean mixtures and decreased lean flammability limits — might qualify the pulsed energy plugs as an enabling technology to effect the mainstream deployment of advanced, ultra-clean and ultra-efficient, spark ignition internal combustion engines. For example, the pulsed energy plug may improve ignition of stratified-GDI engines. Further, the pulsed energy plug technology may improve the attainability of lean-burn homogeneous charge compression ignition combustion by improving the capabilities of spark-assist. Finally, the pulsed energy plug could improve natural gas spark ignition engine development by improving the ignition system. Future work could center efforts on evaluating this spark plug technology in the context of advanced internal combustion engines, to transition the state of the art to the next level.

scholarly journals The influence of centrial forces on crankshaft bearing lubrication is in emergency modes of the engine of the car

2021 ◽  
Vol 12 (2) ◽  
pp. 112-121
Author(s):  
Oleksandr Khrulev ◽  
◽  
Olexii Saraiev ◽  
Iryna Saraieva ◽  
◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Operating Mode ◽  
Internal Combustion ◽  
Technical Condition ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Connecting Rod ◽  
Oil Supply ◽  
Technical Expert ◽  
The Difference

The analysis of the crankshaft bearing condition of the automotive internal combustion engines in the case of insufficiency and breakage of oil supply to them is carried out. It is noted that this fault is one of the most common causes of damage to rubbing pairs in operation. At the same time, the different groups of bearings are often damaged, which cannot be explained within the framework of existing models of plain bearing lubrication. The objective of the work is to develop a mathematical model of oil supply to connecting rod bearings in emergency mode, taking into account the characteristic features of the bearing design. The model also, depending on the nature of the damage, should help to determine and explain the causes of bearing failures if they occur in different modes when operating conditions are broken. A computational model has been developed that makes it possible to assess the effect of design differences in the features of oil supply and the action of the centrifugal forces during crankshaft rotation on the oil column in the lubrication hole where oil is supplied to the conrod bearing. Calculations of the change in time of the oil supply pressure to the connecting rod bearings for the various designs of the crankshaft lubrication holes have been performed. It is shown that, depending on the operating mode of the engine and its design, the oil pressure in front of the connecting rod bearings does not disappear immediately after oil supply failure to crankshaft. Moreover, the lower the crankshaft speed is, the longer the lubrication of the conrod bearings will continue. The calculation results are confirmed by the data of the expert studies of the engine technical condition, in which the crankshaft was wedged in the damaged main bearings was found in the absence of serious damage to the connecting rod ones. It has been found that such features of the damage correspond to an rapid breakage of the oil supply to the crankshaft in the case of such operational damage as the oil pump and pressure reducing valve failure, the oil filter seal and oil pan destruction, etc. The developed model explains the difference in lubrication conditions and in the damage feature to the main and connecting rod bearings in the emergency cases of the oil supply breakage, which are observed during operation, and helps to clarify the failure causes. This makes it possible to use the model and the obtained data when providing auto technical expert studies of the failure causes of automobile internal combustion engines This makes it possible to use the model and the obtained data when providing auto technical expert studies of the failure causes of automobile internal combustion engines when the operating conditions are broken.

scholarly journals Analysis of thermodynamic parameters in spark ignition VCR engine

2019 ◽  
Vol 294 ◽  
pp. 05001
Author(s):  
Patryk Urbański ◽  
Maciej Bajerlein ◽  
Jerzy Merkisz ◽  
Andrzej Ziółkowski ◽  
Dawid Gallas
Keyword(s):  
Thermodynamic Parameters ◽  
Motion Analysis ◽  
Internal Combustion Engines ◽  
Initial Conditions ◽  
Combustion Process ◽  
Internal Combustion ◽  
3D Models ◽  
Spark Ignition ◽  
Combustion Engines ◽  
Combustion Processes

3D models of Szymkowiak and conventional engines were created in the Solidworks program. During the motion analysis, the characteristics of the piston path were analyzed for the two considered engine units. The imported file with the generated piston routes was used in the AVL Fire program, which simulated combustion processes in the two engines with identical initial conditions. The configurations for two different compression ratios were taken into account. The basic thermodynamic parameters occurring during the combustion process in internal combustion engines were analyzed.

Sign in / Sign up

Export Citation Format

Share Document