scholarly journals The Potential Influence of Tree Crown Structure on the Ginkgo Harvest

Forests ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 366
Author(s):  
Yan Xuan ◽  
Linyun Xu ◽  
Guanhua Liu ◽  
Jie Zhou
Keyword(s):  
Natural Frequency ◽  
Economic Value ◽  
Mechanical Vibration ◽  
Element Model ◽  
Fruit Trees ◽  
Vibration Characteristics ◽  
Damping Coefficient ◽  
Additional Energy ◽  
Frequency Model ◽  
Crown Structure

Ginkgo biloba L. has significant health benefits and considerable economic value, but harvesting the fruit is highly labor-intensive. Mechanical vibration harvesting has been shown effective in harvesting various fruit types. In the study of vibration harvesting, the research on the vibration characteristics of fruit trees focuses on the natural frequency (resonance frequency), model, and damping coefficient, which are the main factors affecting the vibration characteristics of trees. But field harvesting experiments have shown that the tree structure may have an impact on the vibration characteristics of the fruit tree and the efficiency of mechanical harvesting. In addition, the research on the damping coefficient of fruit trees is mainly low-frequency damping, and the relevant results cannot be applied to the actual vibration harvesting frequency range. Applying a natural frequency with low damping coefficient to excite a tree can reduce additional energy dissipation. This study explored the influence of ginkgo crown structure on the vibration characteristics and the law of damping changes with frequency. After counting 273 ginkgo trees, two typical ginkgo crown structures, monopodial branching and sympodial branching, were selected to be analyzed for vibration spectrum and damping coefficient. The vibration models for different crown-shaped ginkgo trees were simulated to analyze the vibration state at different frequencies. For sympodial branching ginkgo trees, the consistency of natural frequencies at different branches was better than monopodial branching ginkgo trees. The finite element model analysis shows that monopodial branching ginkgo trees have mainly partial vibrations at different branches when vibrating at high frequencies. The high-frequency vibrations in sympodial branching reflect the better overall vibration of the canopy. The damping coefficients for the two crown types decreased with the increase in frequency. The monopodial branching damping coefficient was 0.0148–0.0298, and the sympodial branching damping coefficient was slightly smaller at 0.0139–0.0248. Based on the test results, the sympodial branching ginkgo tree has better vibration characteristics. The results indicate that controlling the crown structure of fruit trees to be sympodial branching by pruning may help improve the overall vibration characteristics of fruit trees.

Research on the Vibration Characteristic of Composite Rotor for Halfspeed Nuclear Power Turbine-Generator

2017 ◽  
Author(s):  
Xiu-jin Wang
Keyword(s):  
Natural Frequency ◽  
Nuclear Power ◽  
Geometric Model ◽  
Element Model ◽  
Vibration Characteristics ◽  
Turbine Generator ◽  
Element Analysis ◽  
Large Capacity ◽  
Critical Speeds ◽  
Power Turbine

Shafting is one of the key units of large steam turbine generator set, its dynamic characteristics directly affect the technical level and operation effect of the new type large capacity Turbine-generator unit. The forces acting on the disc and the shaft are complex in operation. A composite rotor has various dynamic characters for a large capacity nuclear power Turbine-generator comparing with general rotor for its different structure. Numerical simulation was carried out to a composite rotor for a large capacity nuclear power T-G set, so as to analyze the influence of different length to diameter ratio on the vibration characteristics of the low pressure rotor and to study the effect of Interference Amount Between disc and shaft by using the three-dimensional finite element analysis in order to meet the requirements of the good vibration characteristics of the rotor. Firstly, the geometric model of the rotor is set up, and then the element model of the shafting is built, finally natural frequency of the rotor is calculated by using the mechanical module. Vibration characters such as the natural frequency and corresponding mode were obtained by analysis of vibration for the disc and shaft. The effect of the interference fit on critical speeds of the rotors are analyzed preliminarily. The results show that critical speeds of T-G rotor vary sensitively with magnitude of interference. (CSPE).

Vibration-based delamination evaluation in GFRP composite beams using ANN

2021 ◽  
pp. 096739112110033
Author(s):  
TG Sreekanth ◽  
M Senthilkumar ◽  
S Manikanta Reddy
Keyword(s):  
Finite Element ◽  
Natural Frequency ◽  
Composite Structures ◽  
Composite Beams ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Aviation Industry ◽  
Frequency Data ◽  
Fiber Reinforced ◽  
Back Propagation Algorithm

Delamination is definitely an important topic in the area of composite structures as it progressively worsens the mechanical performance of fiber-reinforced polymer composite structures in its service period. The detection and severity analysis of delaminations in engineering areas like the aviation industry is vital for safety and economic considerations. The existence of delaminations varies the vibration characteristics such as natural frequencies, mode shapes, etc. of composites and hence this indication can be effectively used for locating and quantifying the delaminations. The changes in vibration characteristics are considered as inputs for the inverse problem to determine the location and size of delaminations. In this paper Artificial Neural Network (ANN) is used for delamination evaluationof glass fiber-reinforced composite beams using natural frequency as typical vibration parameter. The Finite Element Analysis is used for generating the required dataset for ANN. The frequency-based delamination prediction technique is validated by finite element models and experimental modal analysis. The results indicate that the ANN-based back propagation algorithm can predict the location and size of delaminations in composites with good accuracy for numerical natural frequency data but the accuracy is comparitivelyless for experimental natural frequency data.

Vibration Characteristics of Rotating Thin Disks—Part I: Experimental Results

2012 ◽  
Vol 79 (4) ◽  
Author(s):  
Ramin M. H. Khorasany ◽  
Stanley G. Hutton
Keyword(s):  
Frequency Response ◽  
Natural Frequency ◽  
Linear Theory ◽  
Lateral Force ◽  
Vibration Characteristics ◽  
Experimental Results ◽  
Rotating Disks ◽  
Critical Speeds ◽  
Applied Forces ◽  
Thin Disks

Analysis of the linear vibration characteristics of unconstrained rotating isotropic thin disks leads to the important concept of “critical speeds.” These critical rotational speeds are of interest because they correspond to the situation where a natural frequency of the rotating disk, as measured by a stationary observer, is zero. Such speeds correspond physically to the speeds at which a traveling circumferential wave, of shape corresponding to the mode shape of the natural frequency being considered, travel around the disk in the absence of applied forces. At such speeds, according to linear theory, the blade may respond as a space fixed stationary wave and an applied space fixed dc force may induce a resonant condition in the disk response. Thus, in general, linear theory predicts that for rotating disks, with low levels of damping, large responses may be encountered in the region of the critical speeds due to the application of constant space fixed forces. However, large response invalidates the predictions of linear theory which has neglected the nonlinear stiffness produced by the effect of in-plane forces induced by large displacements. In the present paper, experimental studies were conducted in order to measure the frequency response characteristics of rotating disks both in an idling mode as well as when subjected to a space fixed lateral force. The applied lateral force (produced by an air jet) was such as to produce displacements large enough that non linear geometric effects were important in determining the disk frequencies. Experiments were conducted on thin annular disks of different thickness with the inner radius clamped to the driving arbor and the outer radius free. The results of these experiments are presented with an emphasis on recording the effects of geometric nonlinearities on lateral frequency response. In a companion paper (Khorasany and Hutton, 2010, “Vibration Characteristics of Rotating Thin Disks—Part II: Analytical Predictions,” ASME J. Mech., 79(4), p. 041007), analytical predictions of such disk behavior are presented and compared with the experimental results obtained in this study. The experimental results show that in the case where significant disk displacements are induced by a lateral force, the frequency characteristics are significantly influenced by the magnitude of forced displacements.

The Finite Element Analysis and Optimization for the Grinder Based on the Joint Surface

2013 ◽  
Vol 281 ◽  
pp. 165-169 ◽  
Author(s):  
Xiang Lei Zhang ◽  
Bin Yao ◽  
Wen Chang Zhao ◽  
Ou Yang Kun ◽  
Bo Shi Yao
Keyword(s):  
Finite Element ◽  
Natural Frequency ◽  
Element Model ◽  
Joint Surface ◽  
Weak Links ◽  
Response Analysis ◽  
Element Analysis ◽  
Static And Dynamic Analysis ◽  
Harmonic Response Analysis ◽  
Grinding Machine

Establish the finite element model for high precision grinding machine which takes joint surface into consideration and then carrys out the static and dynamic analysis of the grinder. After the static analysis, modal analysis and harmonic response analysis, the displacement deformation, stress, natural frequency and vibration mode could be found, which also helps find the weak links out. The improvement scheme which aims to increase the stiffness and precision of the whole machine has proposed to efficiently optimize the grinder. And the first natural frequency of the optimized grinder has increased by 68.19%.

Sheet Material Property Effects upon Dynamic Behavior in Self-Pierce Riveted Joints

2011 ◽  
Vol 675-677 ◽  
pp. 999-1002 ◽  
Author(s):  
Xiao Cong He
Keyword(s):  
Natural Frequency ◽  
Transverse Vibration ◽  
Spot Welding ◽  
Sheet Material ◽  
Vibration Characteristics ◽  
Efficient Design ◽  
Material Density ◽  
Sheet Materials ◽  
Riveted Joints ◽  
Free Transverse Vibration

Self-pierce riveting (SPR) technology offers an alternative to resistance spot welding (RSW) for joining sheet materials. It has been found that the SPR technology produced a much stronger joint than the RSW in fatigue test. For efficient design of SPR structures, the knowledge of dynamic characteristics of the SPR beams is essential. In this paper, the free transverse vibration characteristics of single lap-jointed cantilevered SPR beams are investigated in detail. The focus of the analysis is to reveal the influence on the natural frequency and natural frequency ratio of these beams caused by variations in the material properties of sheet materials to be jointed. It is shown that the transverse natural frequencies of single lap jointed cantilevered SPR beams increase significantly as the Young’s modulus of the sheet materials increases, but change slightly corresponding to the change in Poisson’s ratio. It is also found that the material density of the sheets have significant effects on the free transverse vibration characteristics of the beams.

Temperature and mechanical vibration characteristics of a miniature long external cavity semiconductor laser

1990 ◽  
Vol 26 (15) ◽  
pp. 1159 ◽  
Author(s):  
S.A. Al-Chalabi ◽  
J. Mellis ◽  
M. Hollier ◽  
K.H. Cameron ◽  
R. Wyatt ◽  
...  
Keyword(s):  
Semiconductor Laser ◽  
Mechanical Vibration ◽  
External Cavity ◽  
Vibration Characteristics

Identification of Process Damping Coefficient Based on Material Constitutive Property

2014 ◽  
Author(s):  
Xiaoliang Jin
Keyword(s):  
Energy Dissipation ◽  
Flank Wear ◽  
Orthogonal Cutting ◽  
Element Model ◽  
Machining Process ◽  
Damping Coefficient ◽  
Chatter Stability ◽  
Workpiece Material ◽  
Process Damping ◽  
Constitutive Property

The contact between the tool flank wear land and wavy surface of workpiece causes energy dissipation which influences the tool vibration and chatter stability during a dynamic machining process. The process damping coefficient is affected by cutting conditions and constitutive property of workpiece material. This paper presents a finite element model of dynamic orthogonal cutting process with tool round edge and flank wear land. The process damping coefficient is identified based on the energy dissipation principle. The simulated results are experimentally validated.

Numerical Study for Global Detection of Cracks Embedded in Beams

1999 ◽  
Author(s):  
S. A. Lipsey ◽  
Y. W. Kwon
Keyword(s):  
Finite Element ◽  
Dynamic Analysis ◽  
Natural Frequency ◽  
Mode Shape ◽  
Numerical Study ◽  
Element Model ◽  
Mode Shapes ◽  
Linear Effect ◽  
Modes Of Vibration ◽  
Damage Simulation

Abstract Damage reduces the flexural stiffness of a structure, thereby altering its dynamic response, specifically the natural frequency, damping values, and the mode shapes associated with each natural frequency. Considerable effort has been put into obtaining a correlation between the changes in these parameters and the location and amount of the damage in beam structures. Most numerical research employed elements with reduced beam dimensions or material properties such as modulus of elasticity to simulate damage in the beam. This approach to damage simulation neglects the non-linear effect that a crack has on the different modes of vibration and their corresponding natural frequencies. In this paper, finite element modeling techniques are utilized to directly represent an embedded crack. The results of the dynamic analysis are then compared to the results of the dynamic analysis of the reduced modulus finite element model. Different modal parameters including both mode shape displacement and mode shape curvature are investigated to determine the most sensitive indicator of damage and its location.

Vibration Characteristics of Metamaterial Beams With Periodic Local Resonances

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
M. Nouh ◽  
O. Aldraihem ◽  
A. Baz
Keyword(s):  
Band Gap ◽  
Low Frequency ◽  
Element Model ◽  
Small Mass ◽  
Vibration Characteristics ◽  
Structural Vibrations ◽  
Low Frequencies ◽  
Theoretical Predictions ◽  
Gap Characteristics ◽  
Unique Band

Vibration characteristics of metamaterial beams manufactured of assemblies of periodic cells with built-in local resonances are presented. Each cell consists of a base structure provided with cavities filled by a viscoelastic membrane that supports a small mass to form a source of local resonance. This class of metamaterial structures exhibits unique band gap behavior extending to very low-frequency ranges. A finite element model (FEM) is developed to predict the modal, frequency response, and band gap characteristics of different configurations of the metamaterial beams. The model is exercised to demonstrate the band gap and mechanical filtering capabilities of this class of metamaterial beams. The predictions of the FEM are validated experimentally when the beams are subjected to excitations ranging between 10 and 5000 Hz. It is observed that there is excellent agreement between the theoretical predictions and the experimental results for plain beams, beams with cavities, and beams with cavities provided with local resonant sources. The obtained results emphasize the potential of the metamaterial beams for providing significant vibration attenuation and exhibiting band gaps extending to low frequencies. Such characteristics indicate that metamaterial beams are more effective in attenuating and filtering low-frequency structural vibrations than plain periodic beams of similar size and weight.

scholarly journals Frequency spectrum of the human head–neck to mechanical vibrations

2017 ◽  
Vol 37 (3) ◽  
pp. 611-618 ◽  
Author(s):  
Bin Yang ◽  
Zheng Shi ◽  
Qun Wang ◽  
Feng Xiao ◽  
Tong-Tong Gu ◽  
...  
Keyword(s):  
Finite Element ◽  
Frequency Spectrum ◽  
Mechanical Vibration ◽  
Three Dimensional ◽  
Human Head ◽  
Element Model ◽  
Mode Shapes ◽  
Joint Disorder ◽  
Biomechanical Responses ◽  
Head Neck

This study is based on a real finite element human head–neck model and concentrates on its numerical vibration characteristic. Frequency spectrum and mode shapes of the finite element model of human head–neck under mechanical vibration have been calculated. These vibration characteristics are in good agreement with the previous studies. The simulated fundamental frequency of 35.25 Hz is fairly similar to the published documents, and rarely reported modal responses such as “mastication” and flipping of nasal lateral cartilages modes, however, are introduced by our three-dimensional modal analysis. These additional modes may be of interest to surgeons or clinicians who are specialized in temporomandibular or rhinoplasty joint disorder. Modal validation in terms of modal shapes proposes a necessity for elaborate modeling to identify each individual part’s extra frequencies. Furthermore, it also studies the influence of damping on resonant frequencies and biomechanical responses. It is discovered that damping has an inverse proportionality between damping effect on natural frequency and that on biomechanical responses.

Sign in / Sign up

Export Citation Format

Share Document