scholarly journals Research on the Performance of Pumpjet Propulsor of Different Scales

2022 ◽  
Vol 10 (1) ◽  
pp. 78
Author(s):  
Jun Yang ◽  
Dakui Feng ◽  
Liwei Liu ◽  
Xianzhou Wang ◽  
Chaobang Yao
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Fluid Dynamic ◽  
Open Water ◽  
Small Scale ◽  
Thrust Coefficient ◽  
Total Thrust ◽  
Torque Coefficient ◽  
Open Water Performance ◽  
Thrust And Torque

This study presents a numerical research on the open-water performance of a pumpjet propulsor at different scales. Simulations were performed by an in-house viscous CFD (Computational Fluid Dynamic) code. The Reynolds-averaged Navier–Stokes (RANS) method with SST k-w turbulence model is employed. A dynamic overset grid is used to treat the relative motion between the rotor and other parts. The numerical results are compared with the model test data and they agree well. Comparisons for the open-water performance between the pumpjet propulsors with two scales are carried out. The results indicate that the total thrust coefficient of the large-scale pumpjet propulsor is greater than that of the small-scale one while the torque coefficient is smaller. Therefore, the efficiency of the large-scale pumpjet propulsor is about 8~10% higher than that of the small-scale pumpjet propulsor. The open-water performance of the rotor, pre-swirl stator and duct is obtained separately to estimate the discrepancies on the thrust and torque coefficients between different scales. To analyze the scale effect from different parts, the research on flow field and pressure distribution are carried out. The variation of total thrust and torque coefficient comes mainly from the rotor, which is caused by the flow field, influenced by the duct and stator.

An Investigation Into the Effect of Biofouling on Full-Scale Propeller Performance Using CFD

2019 ◽  
Author(s):  
Soonseok Song ◽  
Yigit Kemal Demirel ◽  
Mehmet Atlar
Keyword(s):  
Open Water ◽  
Full Scale ◽  
Roughness Effect ◽  
Thrust Coefficient ◽  
Propulsion Performance ◽  
Negative Effect ◽  
Precise Prediction ◽  
Torque Coefficient ◽  
Open Water Performance ◽  
Propeller Performance

Abstract The negative effect of biofouling on ship resistance has been investigated since the early days of naval architecture. However, for more precise prediction of fuel consumption of ships, understanding the effect of biofouling on ship propulsion performance is also important. In this study, CFD simulations for the full-scale performance of KP505 propeller in open water, including the presence of marine biofouling, were conducted. To predict the effect of barnacle fouling on the propeller performance, experimentally obtained roughness functions of barnacle fouling were employed in the wall-function of the CFD software. The roughness effect of barnacles of varying sizes and coverages on the propeller open water performance was predicted for advance coefficients ranging from 0.2 to 0.8. From the simulations, drastic effects of barnacle fouling on the propeller open water performance were found. The result suggests that the thrust coefficient decreases while the torque coefficient increases with increasing level of surface fouling, which leads to a reduction of the open water efficiency of the propeller. Further investigations into the roughness effect on the pressure and velocity field, surface pressure and wall shear stress, and propeller vortices were examined.

Influence of Finite Tip Clearance on the Tip Flow Characteristics of Ducted Propeller

2014 ◽  
Vol 889-890 ◽  
pp. 374-379
Author(s):  
Hao Liang Ni ◽  
Jun Wei Zhou ◽  
Da Zheng Wang
Keyword(s):  
Flow Characteristics ◽  
Open Water ◽  
Tip Clearance ◽  
Blade Surface ◽  
Tip Leakage ◽  
Cavitation Performance ◽  
Ducted Propeller ◽  
Torque Coefficient ◽  
Open Water Performance ◽  
Thrust And Torque

The influence of finite tip clearances on the tip flow characteristics, as well as pressure distribution on blade surface near the tip and open water performance of ducted propeller 19A/Ka4-55 model is studied in this paper. It is discovered that tip leakage vortex (TLV for short) disappears when clearance size reduces to a certain extent (0.08% of the propeller radius in this model). The decreasing of tip clearance size also leads to increasing efficiency and better cavitation performance. Besides, variation of thrust and torque coefficient with clearance size show stepped shape instead of linear.

Optimization of RANS Solver Simulation Setup for Propeller Open Water Performance Prediction

2015 ◽  
Author(s):  
Mohammed Islam ◽  
Fatima Jahra ◽  
Michael Doucet
Keyword(s):  
Domain Size ◽  
Open Water ◽  
Fractional Factorial ◽  
Navier Stokes ◽  
Calm Water ◽  
Simulation Results ◽  
Open Water Performance ◽  
Thrust And Torque ◽  
Simulation Time ◽  
Fixed Pitch

Mesh and domain optimization strategies for a RANS solver to accurately estimate the open water propulsive characteristics of fixed pitch propellers are proposed based on examining the effect of different mesh and computation domain parameters. The optimized mesh and domain size parameters were selected using Design of Experiments (DoE) methods enabling simulations to be carried out in a limited memory environment, and in a timely manner; without compromising the accuracy of results. A Reynolds-Averaged Navier Stokes solver is used to predict the propulsive performance of a fixed pitch propeller. The predicted thrust and torque for the propeller were compared to the corresponding measurements. A total of six meshing parameters were selected that could affect the computational results of propeller open water performance. A two-level fractional factorial design was used to screen out parameters that do not significantly contribute to explaining the dependent parameters: namely simulation time, propeller thrust and propeller torque. A total of 32 simulations were carried out only to find out that the selected six meshing parameters were significant in defining the response parameters. Optimum values of each of the input parameters were obtained for the DOE technique and additional simulations were run with those parameters. The simulation results were validated using open water experimental results of the same propeller. It was found that with the optimized meshing arrangement, the propeller opens simulation time was reduced by at least a factor of 6 as compared to the generally popular meshing arrangement. Also, the accuracy of propulsive characteristics was improved by up to 50% as compared to published simulation results. The methodologies presented in this paper can be similarly applied to other simulations such as calm water ship resistance, ship propulsion to systematically derive the optimized meshing arrangement for simulations with minimal simulation time and maximum accuracy. This investigation was carried out using STAR-CCM+, a commercial CFD package; however the findings can be applied to any RANS solver.

scholarly journals A Study on the Instantaneous Turbulent Flow Field in a 90-Degree Elbow Pipe with Circular Section

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Shiming Wang ◽  
Cheng Ren ◽  
Yangfei Sun ◽  
Xingtuan Yang ◽  
Jiyuan Tu
Keyword(s):  
Flow Field ◽  
Turbulent Flow ◽  
Flow Separation ◽  
Large Scale ◽  
Small Scale ◽  
Eddy Simulation ◽  
Dean Vortex ◽  
Instantaneous Flow Field ◽  
Instantaneous Pressure ◽  
Turbulent Flow Field

Based on the special application of 90-degree elbow pipe in the HTR-PM, the large eddy simulation was selected to calculate the instantaneous flow field in the 90-degree elbow pipe combining with the experimental results. The characteristics of the instantaneous turbulent flow field under the influence of flow separation and secondary flow were studied by analyzing the instantaneous pressure information at specific monitoring points and the instantaneous velocity field on the cross section of the elbow. The pattern and the intensity of the Dean vortex and the small scale eddies change over time and induce the asymmetry of the flow field. The turbulent disturbance upstream and the flow separation near the intrados couple with the vortexes of various scales. Energy is transferred from large scale eddies to small scale eddies and dissipated by the viscous stress in the end.

scholarly journals A study of the flow-field evolution and mixing in a planar turbulent jet using direct numerical simulation

2002 ◽  
Vol 450 ◽  
pp. 377-407 ◽  
Author(s):  
S. A. STANLEY ◽  
S. SARKAR ◽  
J. P. MELLADO
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Direct Numerical Simulation ◽  
Large Scale ◽  
Computational Study ◽  
Practical Interest ◽  
Small Scale ◽  
Mixing Process ◽  
Mean Velocity ◽  
Small Scales

Turbulent plane jets are prototypical free shear flows of practical interest in propulsion, combustion and environmental flows. While considerable experimental research has been performed on planar jets, very few computational studies exist. To the authors' knowledge, this is the first computational study of spatially evolving three-dimensional planar turbulent jets utilizing direct numerical simulation. Jet growth rates as well as the mean velocity, mean scalar and Reynolds stress profiles compare well with experimental data. Coherency spectra, vorticity visualization and autospectra are obtained to identify inferred structures. The development of the initial shear layer instability, as well as the evolution into the jet column mode downstream is captured well.The large- and small-scale anisotropies in the jet are discussed in detail. It is shown that, while the large scales in the flow field adjust slowly to variations in the local mean velocity gradients, the small scales adjust rapidly. Near the centreline of the jet, the small scales of turbulence are more isotropic. The mixing process is studied through analysis of the probability density functions of a passive scalar. Immediately after the rollup of vortical structures in the shear layers, the mixing process is dominated by large-scale engulfing of fluid. However, small-scale mixing dominates further downstream in the turbulent core of the self-similar region of the jet and a change from non-marching to marching PDFs is observed. Near the jet edges, the effects of large-scale engulfing of coflow fluid continue to influence the PDFs and non-marching type behaviour is observed.

scholarly journals Prediction of Propeller Performance Using Computational Fluid Dynamics Approach

2019 ◽  
Vol 2 (2) ◽  
pp. 185-193
Author(s):  
Nur Amira Adam ◽  
Ahmad Fitriadhy ◽  
W. S. Kong ◽  
Faisal Mahmuddin ◽  
C. J. Quah
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Cfd Simulation ◽  
Computational Simulation ◽  
Open Water ◽  
Water Model ◽  
Thrust Coefficient ◽  
Propeller Performance ◽  
Prediction Approach ◽  
Thrust And Torque

A reliable prediction approach to obtain a sufficient thrust and torque to propel the ship at desired forward speed is obviously required. To achieve this objective, the authors propose to predict the thrust coefficient (KT), torque coefficient (KQ) and efficiency (η) of the propeller in open-water model test condition using Computational Fluid Dynamics (CFD) simulation approach. The computational simulation presented in the various number of rotational speed (RPM) within the range of advance ratio J=0.1 up to 1.05. The higher value of J lead to decrease 10KQ and KT. While the η increased steadily at the lower value of J and decreased at the higher value of J. The results also showed that the propeller with 1048 rpm obtain a better efficiency at J=0.95 with η= 88.25%, 10KQ=0.1654 and KT= 0.0942. The computation result is very useful as preliminary data for propeller performance characteristics.

scholarly journals Improving accuracy and efficiency of CFD predictions of propeller open water performance

2019 ◽  
Vol 16 (1) ◽  
pp. 1-20
Author(s):  
Mohammed Islam ◽  
Fatima Jahra
Keyword(s):  
Domain Size ◽  
Open Water ◽  
Navier Stokes ◽  
Calm Water ◽  
Open Water Performance ◽  
Improving Accuracy ◽  
Accuracy Of Results ◽  
Thrust And Torque ◽  
Simulation Time ◽  
Fixed Pitch

This research proposes mesh and domain optimization strategies for a popular Computational Fluid Dynamics (CFD) technique to estimate the open water propulsive characteristics of fixed pitch propellers accurately and time-efficiently based on examining the effect of various mesh and computation domain parameters. It used a Reynolds-Averaged Navier-Stokes (RANS) solver to predict the propulsive performance of a fixed pitch propeller with varied meshing, simulation domain and setup parameters. The optimized mesh and domain size parameters were selected using Design of Experiments (DoE) methods enabling simulations in a limited memory and in a timely manner without compromising the accuracy of results. The predicted thrust and torque for the propeller were compared to the corresponding measurements for determining the prediction accuracy. The authors found that the optimized meshing and setup arrangements reduced the propeller opens simulation time by at least a factor of six as compared to the generally popular CFD parameter setup. In addition, the accuracy of propulsive characteristics was improved by up to 50% as compared to published simulation results. The methodologies presented in this paper can be similarly applied to other simulations such as calm water ship resistance, ship propulsion etc. to systematically derive the optimized meshing arrangement for simulations with minimal simulation time and maximum accuracy. This investigation was carried out using a commercial CFD package; however, the findings can be applied to any RANS solver.

scholarly journals Propeller Performance Penalty of Biofouling: Computational Fluid Dynamics Prediction

2020 ◽  
Vol 142 (6) ◽  
Author(s):  
Soonseok Song ◽  
Yigit Kemal Demirel ◽  
Mehmet Atlar
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Characteristics ◽  
Open Water ◽  
Roughness Effect ◽  
Thrust Coefficient ◽  
Propulsion Performance ◽  
Negative Effect ◽  
Open Water Performance ◽  
Propeller Performance

Abstract The negative effect of biofouling on ship resistance has been investigated since the early days of naval architecture. However, for more precise prediction of fuel consumption of ships, understanding the effect of biofouling on ship propulsion performance is also important. In this study, computational fluid dynamics (CFD) simulations for the full-scale performance of KP505 propeller in open water, including the presence of marine biofouling, were conducted. To predict the effect of barnacle fouling on the propeller performance, experimentally obtained roughness functions of barnacle fouling were used in the wall-function of the CFD software. The roughness effect of barnacles of varying sizes and coverages on the propeller open water performance was predicted for advance coefficients ranging from 0.2 to 0.8. From the simulations, drastic effects of barnacle fouling on the propeller open water performance were found. The result suggests that the thrust coefficient decreases while the torque coefficient increases with increasing level of surface fouling, which leads to a reduction of the open water efficiency of the propeller. Using the obtained result, the penalty of propeller fouling on the required shaft power was predicted. Finally, further investigations were made into the roughness effect on the flow characteristics around the propeller and the results were in correspondence with the findings on the propeller open water performance.

Aerodynamic Measurements on a Vertical Axis Wind Turbine in a Large Scale Wind Tunnel

2010 ◽  
Author(s):  
L. Battisti ◽  
L. Zanne ◽  
S. Dell’Anna ◽  
V. Dossena ◽  
B. Paradiso ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Flow Field ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Large Scale ◽  
Fluid Dynamic ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Aerodynamic Optimization ◽  
Vertical Axis Wind Turbines

This paper presents the first results of a wide experimental investigation on the aerodynamics of a vertical axis wind turbine. Vertical axis wind turbines have recently received particular attention, as interesting alternative for small and micro generation applications. However, the complex fluid dynamic mechanisms occurring in these machines make the aerodynamic optimization of the rotors still an open issue and detailed experimental analyses are now highly recommended to convert improved flow field comprehensions into novel design techniques. The experiments were performed in the large-scale wind tunnel of the Politecnico di Milano (Italy), where real-scale wind turbines for micro generation can be tested in full similarity conditions. Open and closed wind tunnel configurations are considered in such a way to quantify the influence of model blockage for several operational conditions. Integral torque and thrust measurements, as well as detailed aerodynamic measurements were applied to characterize the 3D flow field downstream of the turbine. The local unsteady flow field and the streamwise turbulent component, both resolved in phase with the rotor position, were derived by hot wire measurements. The paper critically analyses the models and the correlations usually applied to correct the wind tunnel blockage effects. Results evidence that the presently available theoretical correction models does not provide accurate estimates of the blockage effect in the case of vertical axis wind turbines. The tip aerodynamic phenomena, in particular, seem to play a key role for the prediction of the turbine performance; large-scale unsteadiness is observed in that region and a simple flow model is used to explain the different flow features with respect to horizontal axis wind turbines.

Research on the Application of Body Force in Calculations for Submarine Powering Performance

2013 ◽  
Vol 694-697 ◽  
pp. 41-44
Author(s):  
Xiao Jun Lv ◽  
Qi Dou Zhou ◽  
Zhi Yong Xie
Keyword(s):  
Flow Field ◽  
Body Force ◽  
Leading Edge ◽  
Open Water ◽  
Accurate Prediction ◽  
Computational Error ◽  
Propulsive Efficiency ◽  
The Mean ◽  
Open Water Performance

Using CFD software, the mean wake fraction and thrust deduction fraction are obtained by simulating the flow field around submarine with equally distributed body force adopted to simulate the affection of propeller. The open water performance of propeller 4118 was applied to calculate the rates of propeller rotation required by the submarine at different speeds and corresponding propulsive efficiencies. The comparison between these data and the calculated results of self-propulsion test indicates that a more accurate prediction of the submarine powering performance can be made with the mean wake fraction obtained near the leading edge of the propeller, and the computational error of propulsive efficiency can be reduced to 2%. Research of this paper shows that submarine powering performance can be calculated effectively with the propeller replaced by body force.

Sign in / Sign up

Export Citation Format

Share Document