scholarly journals Experimental Investigations of Timber Beams with Stop-Splayed Scarf Carpentry Joints

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1435
Author(s):  
Anna Karolak ◽  
Jerzy Jasieńko ◽  
Tomasz Nowak ◽  
Krzysztof Raszczuk
Keyword(s):  
Experimental Investigation ◽  
Reference Beam ◽  
Research Programme ◽  
Experimental Investigations ◽  
Italian Renaissance ◽  
Historical Buildings ◽  
Bending Tests ◽  
Load Bearing ◽  
Four Point Bending ◽  
Scarf Joints

The paper presents the results of an experimental investigation of stop-splayed scarf joints, which was carried out as part of a research programme at the Wroclaw University of Science and Technology. A brief description and the characteristics of scarf and splice joints appearing in historical buildings are provided, with special reference to stop-splayed scarf joints (so-called ‘Bolt of lightning’) which were widely used, for example, in Italian renaissance architecture. Analyses and studies of scarf and splice joints in bent elements presented in the literature are reviewed, along with selected examples of analyses and research on tensile joints. It is worth noting that the authors in practically all the cited literature draw attention to the need for further research in this area. Next, the results of the authors’ own research on beams with stop-splayed scarf joints, strengthened using various methods, e.g., by means of drawbolts (metal screws), steel clamps and steel clamps with wooden pegs, which were subjected to four-point bending tests are presented. Load-deflection plots were obtained for load-bearing to bending of each beam in relation to the load-bearing of a continuous reference beam. A comparative analysis of the results obtained for each beam series is presented, along with conclusions and directions for further research.

Comparison of results obtained by static 3- and 4-point bending and flexural vibration tests on solid wood, MDF, and 5-plywood

Holzforschung ◽  
2013 ◽  
Vol 67 (8) ◽  
pp. 941-948 ◽  
Author(s):  
Hiroshi Yoshihara
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Medium Density Fiberboard ◽  
Flexural Vibration ◽  
Solid Wood ◽  
Bending Tests ◽  
Four Point Bending ◽  
Flexural Vibration Test ◽  
The Difference ◽  
Vibration Tests

Abstract The flexural Young’s modulus of western hemlock, medium-density fiberboard, and 5-plywood (made of lauan) has been determined by conducting three- and four-point bending tests with various span lengths and by flexural vibration test. The Young’s modulus was significantly influenced by the deflection measurement method. In particular, the Young’s modulus was not reliable based on the difference between the deflections at two specific points in the specimen, although this test is standardized according to ISO 3349-1975 and JIS Z2101-2009.

scholarly journals Experimental Investigations of Interactions between Sand Wave Movements, Flow Structure, and Individual Aquatic Plants in Natural Rivers: A Case Study of Potamogeton Pectinatus L.

Water ◽  
2018 ◽  
Vol 10 (9) ◽  
pp. 1166 ◽  
Author(s):  
Łukasz Przyborowski ◽  
Anna Łoboda ◽  
Robert Bialik
Keyword(s):  
Flow Velocity ◽  
Three Dimensional ◽  
Potamogeton Pectinatus ◽  
Sand Wave ◽  
Experimental Investigations ◽  
Cross Sectional ◽  
Bending Tests ◽  
Long Duration ◽  
Elevation Changes

Long-duration measurements were performed in two sandy bed rivers, and three-dimensional (3D) flow velocity and bottom elevation changes were measured in a vegetated area and in a clear region of a river. Detailed flow velocity profiles downstream and upstream of a single specimen of Potamogeton pectinatus L. were obtained and the bed morphology was assessed. Potamogeton plants gathered from each river were subjected to tensile and bending tests. The results show that the existence of the plants was influenced by both bottom and flow conditions, as the plants were located where water velocity was lower by 12% to 16% in comparison to clear region. The characteristics of the flow and sand forms depended on the cross-sectional arrangement of the river, e.g., dunes were approximately four times higher in the middle of the river than in vegetated regions near the bank. Furthermore, the studied hydrophytes were too sparse to affect water flow and had no discernible impact on the sand forms’ movements. The turbulent kinetic energy downstream of a single plant was reduced by approximately 25%. Additionally, the plants’ biomechanical characteristics and morphology were found to have adjusted to match the river conditions.

Long-Term Reliability Assessment of Bioceramics for Artificial Joints Using Microdamage Monitoring by AE

2006 ◽  
Vol 309-311 ◽  
pp. 1191-1194
Author(s):  
Shuichi Wakayama ◽  
Teppei Kawakami ◽  
Junji Ikeda
Keyword(s):  
Critical Stress ◽  
Reliability Assessment ◽  
Physiological Saline ◽  
Bending Test ◽  
Unstable Fracture ◽  
Artificial Joints ◽  
Bending Tests ◽  
Four Point Bending

Microfracture process during bending tests of alumina ceramics used for artificial joints was evaluated by acoustic emission (AE) technique. Four-point bending tests were carried out in air, refined water, physiological saline and simulated body fluid. AE behavior during bending test inhibited the rapid increasing point of AE events and energy prior to the final unstable fracture. It was understood that the bending stress at the increasing point corresponds to the critical stress for maincrack formation. The critical stress was affected by water in environments more strongly than fracture strength. Consequently, it was suggested that the characterization of maincrack formation is essential for the long-term reliability assessment of load-bearing bioceramics.

scholarly journals The practice of experimental investigations of lexical tones in Baltic subdialects: some of the new insights in methodology

2020 ◽  
pp. 1-19
Author(s):  
Evaldas Švageris
Keyword(s):  
Experimental Investigation ◽  
Methodological Approach ◽  
Main Idea ◽  
Experimental Investigations ◽  
Lexical Tone ◽  
Mathematical Functions ◽  
Combined Analysis ◽  
Lexical Tones ◽  
Acoustic Correlates ◽  
The Baltic

This article provides an alternative way of experimental investigation of lexical tones in the Baltics. The main idea holds on a presupposition that the phonetic basis of prosodic elements in question can be explained in a more appropriate way in terms of a combined analysis of acoustic correlates, rather than a selective one. The lexical tone in this case may be interpreted as a factor which determines the type of acoustic correlation. Ideally, the interdependence of that sort could be defined by mathematical functions. The analysis of the empirical basis provides clear evidence in the favour of such methodological approach. Phonetic data from both, the Latvian (Valmiera) and the Lithuanian (North Žemaitian) subdialects confirmed clearly that the highest level of the tone distinction can be reached by a combined analysis of the pitch slope, pitch jerk and the duration of the long accented vowels. These results have arguably improved the interpretation of the phonetic tone structure and shed a new light on the typological links between the Baltic dialects. Finally, it presupposes that the phonetic nature of prosodic elements in some degree depends on a methodological way we choose for the investigational purposes. 

Mechanical Properties of Thermal Barrier Coatings at Room Temperature

2005 ◽  
Vol 290 ◽  
pp. 336-339 ◽  
Author(s):  
G. Guidoni ◽  
Y. Torres Hernández ◽  
Marc Anglada
Keyword(s):  
Mechanical Properties ◽  
Thermal Barrier Coatings ◽  
Room Temperature ◽  
Inconel 625 ◽  
Thermal Barrier ◽  
Barrier Coatings ◽  
Bending Tests ◽  
Four Point Bending ◽  
Barrier Coating ◽  
Plasma Sprayed

Four point bending tests have been carried out on a thermal barrier coating (TBC) system, at room temperature. The TBC system consisted of a plasma sprayed Y-TZP top coat with 8 % in weight of Yttria, a bond coat of NiCrAlY and a Ni-based superalloy Inconel 625 as substrate. The TBC coating was deposited on both sides of the prismatic specimens. Efforts have been done in detecting the damage of the coating by means of Maltzbender et al [1] model.

Sign in / Sign up

Export Citation Format

Share Document