scholarly journals A Study for Improving Compressive Strength of Cementitious Mortar Utilizing Magnetic Water

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1971 ◽  
Author(s):  
Omar M. M. Yousry ◽  
Metwally A. Abdallah ◽  
Mariam F. Ghazy ◽  
Mohamed H. Taman ◽  
Mosbeh R. Kaloop
Keyword(s):  
Magnetic Field ◽  
Compressive Strength ◽  
Tap Water ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Super Plasticizer ◽  
Number Of Cycles ◽  
Magnetic Water ◽  
Curing Age

This research investigates the means to improve the compressive strength of mortar mixtures through using novel mixtures. These mixtures include magnetic water (MW) and fly ash (FA). MW was obtained by circulating tap water (TW) through a magnetic field. The magnetization duration was represented by the number of cycles, the content of FA was replaced with cement, and the super plasticizer percentage (SP) and the curing age were used and evaluated experimentally for producing the mortar mixtures. Mortar flow, crushing compressive strength, and ultrasonic pulse velocity (UPV) tests were applied to evaluate the performances of mixing characteristics. The results demonstrate that the MW-treated mortar mixtures show higher compression strength results than those prepared by TW. The compressive strength was increased up to 60% with 150 cycles, a dose of 0.5% of SP and no FA content at the age of 56 days. The dose of SP can be cut down by a maximum of 40% to 50% in cementitious mortar. the workability was enhanced by a percentage of 70%.

scholarly journals PROPERTIES OF CONCRETE MODIFIED BY AMORPHOUS ALUMINA SILICATE

2015 ◽  
Vol 6 (4) ◽  
pp. 178-183 ◽  
Author(s):  
Džigita Nagrockienė ◽  
Giedrius Girskas ◽  
Gintautas Skripkiūnas ◽  
Aurelijus Daugėla
Keyword(s):  
Compressive Strength ◽  
Tap Water ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Hardened Concrete ◽  
Fine Aggregates ◽  
Amorphous Alumina ◽  
Materials Used ◽  
Polycarboxylate Ether

Concrete is the most widely used building material obtained by hardening the mix made of coarse and fine aggregates, cement as the binding material, and water. The basic properties of concrete depend on the quality and properties of cement, w/c ratio and the homogeneity of compaction. Compressive strength is one of the most important properties of concrete. Materials used: Portland cement CEM I 42.5 R, 0/4 fraction sand, 4/16 fraction gravel, amorphous alumina silicate admixture, polycarboxylate ether-based superplasticizer Muraplast FK 63.30, and tap water. Five compositions of concrete mixes containing 0%, 2.5%, 5%, 7.5% and 10% of amorphous alumina silicate admixture by mass of cement were produced. The article analyses the effect of amorphous alumina silicate on the properties of concrete depending on the admixture content. The results revealed that the compressive strength of concrete after 7 days of curing increased by 7.1%, after 28 days of curing increased by 13.3% when the amorphous aluminum oxide doped silicate content was increased to 10%. Amorphous alumina silicate admixture added in quantities of up to 10%, increased the density of hardened concrete by 0.75%, and ultrasonic pulse velocity in specimens with the admixture increased up to 2.63%.

PENGKAJIAN KEKUATAN BETON STRUKTUR JEMBATAN PASCA KEBAKARAN

2013 ◽  
Vol 12 (3) ◽  
Author(s):  
Sudarmadi Sudarmadi
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Strength Assessment ◽  
Concrete Testing

In this paper a case study about concrete strength assessment of bridge structure experiencing fire is discussed. Assessment methods include activities of visual inspection, concrete testing by Hammer Test, Ultrasonic Pulse Velocity Test, and Core Test. Then, test results are compared with the requirement of RSNI T-12-2004. Test results show that surface concrete at the location of fire deteriorates so that its quality is decreased into the category of Very Poor with ultrasonic pulse velocity ranges between 1,14 – 1,74 km/s. From test results also it can be known that concrete compressive strength of inner part of bridge pier ranges about 267 – 274 kg/cm2 and concrete compressive strength of beam and plate experiencing fire directly is about 173 kg/cm2 and 159 kg/cm2. It can be concluded that surface concrete strength at the location of fire does not meet the requirement of RSNI T-12-2004. So, repair on surface concrete of pier, beam, and plate at the location of fire is required.

scholarly journals The Hydration, Mechanical, Autogenous Shrinkage, Durability, and Sustainability Properties of Cement–Limestone–Slag Ternary Composites

2021 ◽  
Vol 13 (4) ◽  
pp. 1881
Author(s):  
Mei-Yu Xuan ◽  
Yi Han ◽  
Xiao-Yong Wang
Keyword(s):  
Compressive Strength ◽  
Electrical Resistivity ◽  
Experimental Studies ◽  
Autogenous Shrinkage ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Hydration Heat ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio

This study examines the hydration–mechanical–autogenous shrinkage–durability–sustainability properties of ternary composites with limestone filler (LF) and ground-granulated blast furnace slag (BFS). Four mixtures were prepared with a water/binder ratio of 0.3 and different replacement ratios varying from 0 to 45%. Multiple experimental studies were performed at various ages. The experimental results are summarized as follows: (1) As the replacement levels increased, compressive strength and autogenous shrinkage (AS) decreased, and this relationship was linear. (2) As the replacement levels increased, cumulative hydration heat decreased. At the age of 3 and 7 days, there was a linear relationship between compressive strength and cumulative hydration heat. (3) Out of all mixtures, the ultrasonic pulse velocity (UPV) and electrical resistivity exhibited a rapid increase in the early stages and tended to slow down in the latter stages. There was a crossover of UPV among various specimens. In the later stages, the electrical resistivity of ternary composite specimens was higher than plain specimens. (4) X-ray diffraction (XRD) results showed that LF and BFS have a synergistic effect. (5) With increasing replacement ratios, the CO2 emissions per unit strength reduced, indicating the sustainability of ternary composites.

Estimation of Compressive Strength of Recycled Aggregate High Strength Concrete Using Ultrasonic Pulse Velocity

2014 ◽  
Vol 605 ◽  
pp. 147-150
Author(s):  
Seong Uk Hong ◽  
Seung Hun Kim ◽  
Yong Taeg Lee
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
Coarse Aggregate ◽  
High Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Recycled Aggregate ◽  
Strength Concrete ◽  
Recycled Coarse Aggregate

This study used the ultrasonic pulse velocity method, one of the non-destructive test methods that does not damage the building for maintenance of to-be-constructed concrete structures using recycled aggregates in order to estimate the compressive strength of high strength concrete structure using recycled coarse aggregate and provide elementary resources for technological establishment of ultrasonic pulse velocity method. 200 test pieces of high strength concrete 40, 50MPa using recycled coarse aggregate were manufactured by replacement rates (0, 30, 50, 100%) and age (1, 7, 28, 180days), and air curing was executed to measure compressive strength and wave velocity. As the result of compressive strength measurement, the one with age of 180day and design strength of 40MPa was 43.69MPa, recycled coarse aggregate replacement rate of 30% 50% 100% were 42.82, 41.22, 37.35MPa, and 50MPa was 52.50MPa, recycled coarse aggregate replacement rate of 30% 50% 100% were 49.02, 46.66, 45.30MPa, and while it could be seen that the test piece substituted with recycled aggregate was found to have lower strength than the test piece with natural aggregate only, but it still reached the design strength to a degree. The correlation of compressive strength and ultrasonic pulse velocity was found and regression analysis was conducted. The estimation formula for compressive strength of high strength concrete using recycled coarse aggregate was found to be Fc=0.069Vp4.05, R2=0.66

scholarly journals Performance Evaluation of Concrete using Marble Mining Waste

2016 ◽  
Vol 11 (2) ◽  
pp. 53-66 ◽  
Author(s):  
Sudarshan Dattatraya Kore ◽  
A. K. Vyas
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Mining Waste ◽  
Partial Replacement ◽  
Infrastructure Development ◽  
The Impact ◽  
Marble Waste

Abstract A huge amount waste (approximately 60%) is generated during mining and processing in marble industries. Such waste can be best utilized in infrastructure development works. Coarse aggregate 75% by weight was replaced by aggregate obtained from marble mining waste. The impact of marble waste as a partial replacement for conventional coarse aggregate on the properties of concrete mixes such as workability, compressive strength, permeability, abrasion, etc. was evaluated. The test results revealed that the compressive strength was comparable to that of control concrete. Other properties such as workability of concrete increased, water absorption reduced by 17%, and resistance to abrasion was marginally increased by 2% as compared to that of control concrete. Ultrasonic pulse velocity and FTIR results show improvement in quality of concrete with crushed marble waste. From the TGA analysis it was confirmed that, aggregate produced from marble waste shows better performance under elevated temperature than that of conventional aggregates.

scholarly journals Assessment of Concrete Compressive Strength by Ultrasonic Non-Destructive Test

2021 ◽  
Vol 318 ◽  
pp. 03004
Author(s):  
AbdulMuttalib I. Said ◽  
Baqer Abdul Hussein Ali
Keyword(s):  
Compressive Strength ◽  
Salt Content ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Experimental Program ◽  
Concrete Compressive Strength ◽  
Statistical Program ◽  
Non Destructive ◽  
Accurate Relation

This paper has carried out an experimental program to establish a relatively accurate relation between the ultrasonic pulse velocity (UPV) and the concrete compressive strength. The program involved testing concrete cubes of (100) mm and prisms of (100×100×300) cast with specified test variables. The samples are tested by using ultrasonic test equipment with two methods, direct ultrasonic pulse (DUPV) and surface (indirect) ultrasonic pulse (SUPV) for each sample. The obtained results were used as input data in the statistical program (SPSS) to predict the best equation representing the relation between the compressive strength and the ultrasonic pulse velocity. In this research 383 specimens were tested, and an exponential equation is proposed for this purpose. The statistical program has been used to prove which type of UPV is more suitable, the (SUPV) test or the (DUPV) test, to represent the relation between the ultrasonic pulse velocity and the concrete compressive strength. In this paper, the effect of salt content on the connection between the ultrasonic pulse velocity and the concrete compressive strength has also been studied.

Sign in / Sign up

Export Citation Format

Share Document