scholarly journals Influence of Phosphorus Slag on Physical and Mechanical Properties of Cement Mortars

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2390
Author(s):  
Min Pang ◽  
Zhenping Sun ◽  
Ming Chen ◽  
Jianlei Lang ◽  
Jiayan Dong ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Chemical Activation ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Water Requirement ◽  
Hydration Heat ◽  
Physical Activation ◽  
Cement Pastes ◽  
Cement Mortars ◽  
Chemical Activator

Influences of phosphorus slag from 10% to 50% (by mass) on the setting time and the water requirement of the normal consistency of cement pastes, flowability, resistance to carbonation, and the compressive strength of cement mortars were investigated. The physical activation by improving fineness and the chemical activation by adding the chemical activator were evaluated by the compressive strength of cement mortars with 30% by mass of phosphorus slag. Hydration heat, X-ray diffraction, and scanning electron microscopy were used to study the microstructure of cement pastes and mortars with 30% by mass of phosphorus slag and the chemical activator. Results showed that the setting time of cement pastes was delayed by phosphorus slag from 10% to 50%. Phosphorus slag had nearly no effects on the water requirement of the normal consistency of cement pastes and the flowability of cement mortars. The resistance to carbonation of cement mortars was decreased by phosphorus slag from 10% to 50% according to the acceleration carbonation. The compressive strength of cement mortars was also decreased by phosphorus slag from 10% to 50% and the low activity of phosphorus slag was concluded based on compressive strength of cement mortars. The effect of the chemical activator on the compressive strength of cement mortars with 30% by mass of phosphorus slag was better than improving fineness of phosphorus slag from 300 m2/kg to 450 m2/kg. Both hydration heat and cement hydrates were inhibited by phosphorus slag and could be partly compensated by the chemical activator. Loose morphology and propagations of microcracks were found in cement pastes and mortars with 30% by mass of phosphorus slag.

Properties of Cement Mortars Mixed with SiO2 and CaCO3 Nanoparticles

2013 ◽  
Vol 539 ◽  
pp. 244-248
Author(s):  
De Zhi Wang ◽  
Yin Yan Zhang ◽  
Yun Fang Meng
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Cement Mortar ◽  
Negative Impact ◽  
Setting Time ◽  
Water Requirement ◽  
Mineral Admixtures ◽  
Cement Pastes ◽  
Optimal Replacement ◽  
Cement Mortars

Water requirement of normal consistency, setting time and soundness of cement pastes mixed with SiO2 and CaCO3 nanoparticle and the flexural strength and compressive strength of cement mortars mixed with SiO2 and CaCO3 nanoparticles were experimentally studied. Results indicated that the added nano-SiO2 and nano-CaCO3 with a mass account of 4.0 wt. % decreased the setting time and increased the water requirement of normal consistency, flexural strength and compressive strength. And these nanoscaled mineral admixtures did not have a negative impact on cement soundness. The optimal replacement levels of cement by SiO2 and CaCO3 nanoparticles for producing cement mortar with improved strength were 2.0 and 4.0 wt.% respectively.

Influence of Nano-Clay on the Performance of phosphoaluminate cement

2012 ◽  
Vol 535-537 ◽  
pp. 1670-1672
Author(s):  
Jian Lei Wang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Water Requirement ◽  
Experimental Results ◽  
Nano Clay

The influence of nano-clay on the physical and mechanical properties of the phosphoaluminate cement (PALC) was studied in the paper. The experimental results showed that nano-clay changed the water requirement of normal consistency and the setting time of phosphoaluminate cement. However its soundness was not affected by adding nano-clay. With 3% nano-clay added by weight of cement, PALC has an optimum compressive strength.

Investigation on Hydration Characteristics of Zinc-Doped Portland Cement Pastes

2010 ◽  
Vol 168-170 ◽  
pp. 623-627 ◽  
Author(s):  
Xiang Guo Li ◽  
Xiao Bo Yin ◽  
Bao Guo Ma ◽  
Bei Wu ◽  
Quanbin Chen ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Setting Time ◽  
Hydration Product ◽  
Hydration Heat ◽  
Cement Pastes ◽  
Ion Concentrations ◽  
Zn Concentration ◽  
Zinc Salts ◽  
Hydration Characteristics

Compressive strength, setting time, hydration heat and hydration product were investigated to evaluate the effects of Zn2+ ion concentrations and the anion of zinc salts on the hydration characteristics of Portland cement paste. The results show that the hydration characteristics of zinc-doped cement pastes depend on Zn2+ ion concentrations and the anion of salts. With the incorporation of ZnCl2, the hydration heat, exothermic rate and the early-age strength of cement pastes were reduced, the arrival time of the highest temperature was delayed, and little negative influences on the compressive strength at 28 days were observed. The total hydration did not decrease incorporating ZnSO4; the hydration exothermic process was delayed. There were little negative influences on the compressive strength of the samples at 3 days and 28 days. Moreover, for the samples with the same Zn concentration, the retardation effect of ZnCl2 samples was stronger than that of ZnSO4 samples.

scholarly journals Effect of Calcium Nitrate on the Properties of Portland–Limestone Cement-Based Concrete Cured at Low Temperature

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1611
Author(s):  
Gintautas Skripkiūnas ◽  
Asta Kičaitė ◽  
Harald Justnes ◽  
Ina Pundienė
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Setting Time ◽  
Calcium Nitrate ◽  
Curing Temperature ◽  
Hardened Concrete ◽  
Cement Pastes ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Early Strength

The effect of calcium nitrate (CN) dosages from 0 to 3% (of cement mass) on the properties of fresh cement paste rheology and hardening processes and on the strength of hardened concrete with two types of limestone-blended composite cements (CEM II A-LL 42.5 R and 42.5 N) at different initial (two-day) curing temperatures (−10 °C to +20 °C) is presented. The rheology results showed that a CN dosage up to 1.5% works as a plasticizing admixture, while higher amounts demonstrate the effect of increasing viscosity. At higher CN content, the viscosity growth in normal early strength (N type) cement pastes is much slower than in high early strength (R type) cement pastes. For both cement-type pastes, shortening the initial and final setting times is more effective when using 3% at +5 °C and 0 °C. At these temperatures, the use of 3% CN reduces the initial setting time for high early strength paste by 7.4 and 5.4 times and for normal early strength cement paste by 3.5 and 3.4 times when compared to a CN-free cement paste. The most efficient use of CN is achieved at −5 °C for compressive strength enlargement; a 1% CN dosage ensures the compressive strength of samples at a −5 °C initial curing temperature, with high early strength cement exceeding 3.5 MPa but being less than the required 3.5 MPa in samples with normal early strength cement.

scholarly journals Effect of Waste Glass on the Properties and Microstructure of Magnesium Potassium Phosphate Cement

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2073
Author(s):  
Qiubai Deng ◽  
Zhenyu Lai ◽  
Rui Xiao ◽  
Jie Wu ◽  
Mengliang Liu ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Glass Powder ◽  
Setting Time ◽  
Potassium Phosphate ◽  
Heat Of Hydration ◽  
Waste Glass ◽  
Hydration Heat ◽  
Magnesium Potassium Phosphate Cement ◽  
The Matrix ◽  
Powder Content

Waste glass is a bulk solid waste, and its utilization is of great consequence for environmental protection; the application of waste glass to magnesium phosphate cement can also play a prominent role in its recycling. The purpose of this study is to evaluate the effect of glass powder (GP) on the mechanical and working properties of magnesium potassium phosphate cement (MKPC). Moreover, a 40mm × 40mm × 40mm mold was used in this experiment, the workability, setting time, strength, hydration heat release, porosity, and microstructure of the specimens were evaluated. The results indicated that the addition of glass powder prolonged the setting time of MKPC, reduced the workability of the matrix, and effectively lowered the hydration heat of the MKPC. Compared to an M/P ratio (MgO/KH2PO4 mass ratio) of 1:1, the workability of the MKPC with M/P ratios of 2:1 and 3:1 was reduced by 1% and 2.1%, respectively, and the peak hydration temperatures were reduced by 0.5% and 14.6%, respectively. The compressive strength of MKPC increased with an increase in the glass powder content at the M/P ratio of 1:1, and the addition of glass powder reduced the porosity of the matrix, effectively increased the yield of struvite-K, and affected the morphology of the hydration products. With an increase in the M/P ratio, the struvite-K content decreased, many tiny pores were more prevalent on the surface of the matrix, and the bonding integrity between the MKPC was weakened, thereby reducing the compressive strength of the matrix. At less than 40 wt.% glass powder content, the performance of MKPC improved at an M/P ratio of 1:1. In general, the addition of glass powders improved the mechanical properties of MKPC and reduced the heat of hydration.

scholarly journals Development of a Zero-Cement Binder Using Slag, Fly Ash, and Rice Husk Ash with Chemical Activator

2015 ◽  
Vol 2015 ◽  
pp. 1-14 ◽  
Author(s):  
M. R. Karim ◽  
M. F. M. Zain ◽  
M. Jamil ◽  
F. C. Lai
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Setting Time ◽  
Time Flow ◽  
Alumina Gel ◽  
Cement Binder ◽  
Increasing Demand ◽  
Chemical Activator

The increasing demand and consumption of cement have necessitated the use of slag, fly ash, rice husk ash (RHA), and so forth as a supplement of cement in concrete construction. The aim of the study is to develop a zero-cement binder (Z-Cem) using slag, fly ash, and RHA combined with chemical activator. NaOH, Ca(OH)2, and KOH were used in varying weights and molar concentrations. Z-Cem was tested for its consistency, setting time, flow, compressive strength, XRD, SEM, and FTIR. The consistency and setting time of the Z-Cem paste increase with increasing RHA content. The Z-Cem mortar requires more superplasticizer to maintain a constant flow of110±5% compared with OPC. The compressive strength of the Z-Cem mortar is significantly influenced by the amounts, types, and molar concentration of the activators. The Z-Cem mortar achieves a compressive strength of 42–44 MPa at 28 days with 5% NaOH or at 2.5 molar concentrations. The FTIR results reveal that molecules in the Z-Cem mortar have a silica-hydrate (Si-H) bond with sodium or other inorganic metals (i.e., sodium/calcium-silica-hydrate-alumina gel). Therefore, Z-Cem could be developed using the aforementioned materials with the chemical activator.

scholarly journals CONTINUOUS MICROSTRUCTURAL CORRELATION OF SLAG/SUPERPLASTICIZER CEMENT PASTES BY HEAT AND IMPEDANCE METHODS VIA FRACTAL ANALYSIS

Fractals ◽  
2017 ◽  
Vol 25 (04) ◽  
pp. 1740003 ◽  
Author(s):  
S. W. TANG ◽  
R. J. CAI ◽  
Z. HE ◽  
X. H. CAI ◽  
H. Y. SHAO ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fractal Analysis ◽  
Setting Time ◽  
Blended Cement ◽  
Impedance Measurement ◽  
Heat Evolution ◽  
Early Age ◽  
Contact Impedance ◽  
Cement Pastes ◽  
Early Age Hydration

This paper presents a preliminary work to evaluate the influence of slag and superplasticizer on the early-age hydration of cement pastes by an innovative non-contact impedance measurement, heat evolution method, compressive strength and setting time tests. Besides, the cumulative pore volume obtained from modulus and phase of impedance in different hydration sections is taken to continuously correlate the cumulative heat releasing of cement pastes via the fractal analysis. Retarded phenomena and mechanism of hydration in cement pastes incorporated with slag and superplasticizer are studied, respectively. It is found that the compressive strength and setting time have a good linear relation with the slag amount in blended cement pastes.

Physical and mechanical characteristics of cement mortars and concretes with addition of clinoptilolite from Beli Plast deposit (Bulgaria), silica fume and fly ash

Clay Minerals ◽  
2011 ◽  
Vol 46 (2) ◽  
pp. 213-223 ◽  
Author(s):  
V. Lilkov ◽  
I. Rostovsky ◽  
O. Petrov
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Mechanical Characteristics ◽  
Physical And Mechanical Properties ◽  
Specific Pore Volume ◽  
Cement Mortars ◽  
Physical And Mechanical Characteristics

AbstractCement mortars and concretes incorporating clinoptilolite, silica fume and fly ash were investigated for changes in their physical and mechanical properties. It was found that additions of 10% clinoptilolite and 10% Pozzolite (1:1 mixture of silica fume and fly ash) were optimal for improvement of the quality of the hardened products, giving 8% and 13% increases in flexural and compressive strength respectively. The specific pore volume of the mortars incorporating zeolite decreased between the 28th and 180th day to levels below the values for the control composition due to the fact that clinoptilolite exhibits its pozzolanic activity later in the hydration. In these later stages, pores with radii below 500 nm increased at the expense of larger pores. The change in the pore-size distribution between the first and sixth months of hydration occurs mostly in the mortars with added zeolite.

scholarly journals Effect of fly ash on physical and mechanical properties of mortar

2019 ◽  
Vol 17 (6) ◽  
pp. 35
Author(s):  
Vu-An Tran
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Water Absorption ◽  
Thermal Power ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Flow Density ◽  
Control Specimen

This research investigates the physical and mechanical properties of mortar incorporating fly ash (FA), which is by-product of Duyen Hai thermal power plant. Six mixtures of mortar are produced with FA at level of 0%, 10%, 20%, 30%, 40%, and 50% (by volume) as cement replacement and at water-to-binder (W/B) of 0.5. The flow, density, compressive strength, flexural strength, and water absorption tests are made under relevant standard in this study. The results have shown that the higher FA content increases the flow of mortar but significantly decreases the density of mixtures. The water absorption and setting time increases as the samples incorporating FA. Compressive strength of specimen with 10% FA is approximately equal to control specimen at the 91-day age. The flexural strength of specimen ranges from 7.97 MPa to 8.94 MPa at the 91-day age with the best result for samples containing 10% and 20% FA.

scholarly journals Influence of electric arc furnace dust and lime kiln waste in Portland cement hydration

2020 ◽  
Vol 20 (4) ◽  
pp. 225-241
Author(s):  
Josué Claudio Metz ◽  
Elenize Ferreira Maciel ◽  
Marilise Garbin ◽  
Regina Célia Espinosa Modolo ◽  
Carlos Alberto Mendes Moraes ◽  
...  
Keyword(s):  
Portland Cement ◽  
Setting Time ◽  
Construction Materials ◽  
Electric Arc Furnace ◽  
Electric Arc ◽  
Hydration Heat ◽  
Arc Furnace ◽  
Cement Pastes ◽  
Electric Arc Furnace Dust ◽  
Lime Kiln

Abstract Studies have indicated that the use of electric arc furnace dust (EAFD) results in a delay in the hydration time of Portland cement. Calcium-rich waste such as lime kiln waste (LKW) is one of the techniques used to offset this delay as it accounts for the lack of this element in calcium silicate hydrate (C-S-H) production in the mixture. The objective of this study was to evaluate the influence of electric arc furnace dust (EAFD) and lime kiln waste (LKW) in the hydration process of Portland cement pastes and their influence in setting time and hydration heat. The methodology used required several steps: physiochemical and micro-structural characterization of waste samples; definition and production cement pastes with different levels of waste substitution and a reference paste and evaluation of the cement pastes with respect to setting time and hydration heat. Results showed that the substitution of 1% EAFD with or without LKW presented similar hydration heats as the reference paste. This indicated that EAFD+LKW substitution would not affect substantially the hydration reactions of cement and could allow waste recycling in construction materials.

Sign in / Sign up

Export Citation Format

Share Document