scholarly journals Effect of Strain Rate on the Mechanical Properties of Cu/Ni Clad Foils

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6846
Author(s):  
Haiyang Wang ◽  
Chuanjie Wang ◽  
Linfu Zhang ◽  
Gang Chen ◽  
Qiang Zhu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Interface Layer ◽  
Strain Rate Range ◽  
Coarse Grained ◽  
Uniaxial Tensile ◽  
Rate Range ◽  
Static Strain

The performance of clad foils in microforming deserves to be studied extensively, where the strain rate sensitivity of the clad foil concerning the forming performance is a crucial factor. In this paper, the strain rate sensitivity of the mechanical properties of coarse-grained (CG) Cu/Ni clad foils in the quasi-static strain rate range (ε˙=10−4 s−1~10−1 s−1) is explored by uniaxial tensile tests under different strain rates. The results show that the strength and ductility increase with strain rate, and the strain rate sensitivity m value is in the range of 0.012~0.015, which is three times the value of m for CG pure Cu. The fracture morphology shows that slip bands with different directions are entangled in localized areas near the interface layer. Molecular dynamics simulations demonstrate the formation of many edged dislocations at the Cu/Ni clad foils interface due to a mismatch interface. The improved ductility and strain rate sensitivity is attributed to the interaction and plugging of the edged dislocations with high density in the interface layer. Additionally, the influence of size effect on mechanical properties is consistently present in the quasi-static strain rate range. This paper helps to understand the strain rate sensitivity of CG clad foils and to develop clad foils in microforming processes.

scholarly journals Study on Plastic Deformation Behavior of Mo-10Ta under Ultra-High Strain Rate

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1153
Author(s):  
Ping Song ◽  
Wen-Bin Li ◽  
Yu Zheng ◽  
Jiu-Peng Song ◽  
Xiang-Cao Jiang ◽  
...  
Keyword(s):  
Activation Energy ◽  
High Strain Rate ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Deformation Behavior ◽  
High Strain ◽  
Rate Sensitivity ◽  
Strain Rate Range ◽  
Rate Range ◽  
Strain Relationship

This study investigated the deformation behavior of the Mo-10Ta alloy with a strain rate range of 102–105 s−1. The Split Hopkinson pressure bar (SHPB) experiments were conducted to investigate the influence of deformation conditions on the stress-strain relationship and strain rate sensitivity of the material within a strain rate range of 0.001–4500 s−1. The Shaped Charge Jet (SCJ) forming experiments under detonation loading was conducted to clarify the dynamic response and microstructure evolution of the material within an ultra-high strain rates range of 104–105 s−1. Based on the stress-strain relationship of Mo-10Ta alloy at high temperature (286–873 K) and high strain rate (460–4500 s−1), the influence of temperature and strain rate on the activation energy Q was analyzed. The results indicate that the material strain rate sensitivity increased with the increase in strain rate and strain. Meanwhile, the activation energy Q decreased as the temperature and strain rate increased. The plasticity of the Mo-10Ta alloy under the condition of SCJ forming was substantially enhanced compared with that under quasi-static deformation. The material grain was also refined under ultra-high strain rate, as reflected by the reduction in grain size from 232 μm to less than 10 μm.

Effect of Strain Rate on Constitutive Behavior of AA-5052 H34

2013 ◽  
Vol 535-536 ◽  
pp. 60-63 ◽  
Author(s):  
Prince Sharma ◽  
Pradeep Chandel ◽  
Vikas Mangla ◽  
Puneet Mahajan ◽  
Manjit Singh
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Split Hopkinson Pressure Bar ◽  
Rate Sensitivity ◽  
Tensile Tests ◽  
Strain Rate Range ◽  
Gauge Length ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Rate Range

This paper presents the experimental results to analyze the strain rate sensitivity of aluminium alloy AA-5052 H34. The experiments were carried out under uniaxial tension as well as compression. Tensile tests were carried out with UTM (Zwick Z-250) in the strain rate range of 10-4 to 10-1 s-1 using standard ASTM specimen with gauge length 50mm. Compression tests were carried out in the strain rate range of 10-4 to 103 s-1 using UTM and Split Hopkinson Pressure Bar. Cylindrical specimens of 10mm diameter and 10mm thickness were used for compression experiments. The material showed negative strain rate sensitivity in strain rate from 10-4 to 1 s-1 but showed positive strain rate sensitivity when strain rate increased to 103 s-1. The material was found to be susceptible to Portevin–Le Chatelier effect.

Strain-Rate Sensitive Mechanical Properties of Tendon Fascicles From Mice With Genetically Engineered Alterations in Collagen and Decorin

2004 ◽  
Vol 126 (2) ◽  
pp. 252-257 ◽  
Author(s):  
Paul S. Robinson ◽  
Tony W. Lin ◽  
Paul R. Reynolds ◽  
Kathleen A. Derwin ◽  
Renato V. Iozzo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Structure Function ◽  
Elastic Properties ◽  
Strain Rate Sensitivity ◽  
Type I Collagen ◽  
Rate Sensitivity ◽  
Genetically Engineered ◽  
Uniaxial Tensile ◽  
Type I

Tendons have complex mechanical behaviors that are nonlinear and time dependent. It is widely held that these behaviors are provided by the tissue’s composition and structure. It is generally thought that type I collagen provides the primary elastic strength to tendon while proteoglycans, such as decorin, play a role in failure and viscoelastic properties. This study sought to quantify such structure-function relationships by comparing tendon mechanical properties between normal mice and mice genetically engineered for altered type I collagen content and absence of decorin. Uniaxial tensile ramp to failure experiments were performed on tail tendon fascicles at two strain rates, 0.5%/s and 50%/s. Mutations in type I collagen led to reduced failure load and stiffness with no changes in failure stress, modulus or strain rate sensitivity. Fascicles without decorin had similar elastic properties to normal fascicles, but reduced strain rate sensitivity. Fascicles from immature mice, with increased decorin content compared to adult fascicles, had inferior elastic properties but higher strain rate sensitivity. These results showed that tendon viscoelasticity is affected by decorin content but not by collagen alterations. This study provides quantitative evidence for structure-function relationships in tendon, including the role of proteoglycan in viscoelasticity.

Local Investigations of the Mechanical Properties of Ultrafine Grained Metals by Nanoindentations

2006 ◽  
Vol 503-504 ◽  
pp. 31-36 ◽  
Author(s):  
Johannes Mueller ◽  
Karsten Durst ◽  
Dorothea Amberger ◽  
Matthias Göken
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Fcc Metals ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Indentation Strain

The mechanical properties of ultrafine-grained metals processed by equal channel angular pressing is investigated by nanoindentations in comparison with measurements on nanocrystalline nickel with a grain size between 20 and 400 nm produced by pulsed electrodeposition. Besides hardness and Young’s modulus measurements, the nanoindentation method allows also controlled experiments on the strain rate sensitivity, which are discussed in detail in this paper. Nanoindentation measurements can be performed at indentation strain rates between 10-3 s-1 and 0.1 s-1. Nanocrystalline and ultrafine-grained fcc metals as Al and Ni show a significant strain rate sensitivity at room temperature in comparison with conventional grain sized materials. In ultrafine-grained bcc Fe the strain rate sensitivity does not change significantly after severe plastic deformation. Inelastic effects are found during repeated unloading-loading experiments in nanoindentations.

scholarly journals Strain-Rate-Dependent Deformation Behavior and Mechanical Properties of a Multi-Phase Medium-Manganese Steel

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 344 ◽  
Author(s):  
Simon Sevsek ◽  
Christian Haase ◽  
Wolfgang Bleck
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Deformation Behavior ◽  
Rate Sensitivity ◽  
Manganese Steel ◽  
Strain Rates ◽  
Rate Dependent ◽  
Medium Manganese Steel ◽  
Multi Phase

The strain-rate-dependent deformation behavior of an intercritically annealed X6MnAl12-3 medium-manganese steel was analyzed with respect to the mechanical properties, activation of deformation-induced martensitic phase transformation, and strain localization behavior. Intercritical annealing at 675 °C for 2 h led to an ultrafine-grained multi-phase microstructure with 45% of mostly equiaxed, recrystallized austenite and 55% ferrite or recovered, lamellar martensite. In-situ digital image correlation methods during tensile tests revealed strain localization behavior during the discontinuous elastic-plastic transition, which was due to the localization of strain in the softer austenite in the early stages of plastic deformation. The dependence of the macroscopic mechanical properties on the strain rate is due to the strain-rate sensitivity of the microscopic deformation behavior. On the one hand, the deformation-induced phase transformation of austenite to martensite showed a clear strain-rate dependency and was partially suppressed at very low and very high strain rates. On the other hand, the strain-rate-dependent relative strength of ferrite and martensite compared to austenite influenced the strain partitioning during plastic deformation, and subsequently, the work-hardening rate. As a result, the tested X6MnAl12-3 medium-manganese steel showed a negative strain-rate sensitivity at very low to medium strain rates and a positive strain-rate sensitivity at medium to high strain rates.

scholarly journals Strain Rate Sensitivity of Epoxy Composites Reinforced with Varied Sizes of Bagasse Particles

2020 ◽  
Vol 4 (3) ◽  
pp. 110
Author(s):  
Sujan Debnath ◽  
Tan Ke Khieng ◽  
Mahmood Anwar ◽  
Animesh Kumar Basak ◽  
Alokesh Pramanik
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Interfacial Strength ◽  
Rate Sensitivity ◽  
Natural Fibre ◽  
Filler Loading ◽  
Epoxy Composites ◽  
Fibre Reinforced Polymer ◽  
Filler Particles

Viscoelastic materials, such as natural fibre-reinforced polymer composites, are strain rate sensitive. In the present investigation, the low strain rate sensitivity (0.00028 s−1, 0.00085 s−1 and 0.0017 s−1) of different sized bagasse particle-reinforced (212 µm and 300 µm) epoxy composites was examined using the Weibull analysis method. The filler loading content was optimized at 2 wt.% to achieve better mechanical properties. Based on the experimental results, it was observed that composites with 212 µm filler particles had higher characteristic strengths, more consistent failure strengths and higher energy absorption properties with higher loading speeds, compared to that of 300 µm filler particles. Based on the mathematical models for particle–matrix interactions, improvements in mechanical properties are attributed to proper filler dispersion and a better fibre–matrix interfacial strength.

Strain Rate Sensitivity of Ultrafine-Grained CP-Ti Processed by ECAP at Room Temperature

2010 ◽  
Vol 667-669 ◽  
pp. 707-712 ◽  
Author(s):  
Xiao Yan Liu ◽  
Xi Cheng Zhao ◽  
Xi Rong Yang
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Strain Rate Range ◽  
Compression Tests ◽  
Ultrafine Grained ◽  
Die Set ◽  
Increasing Temperature ◽  
Cp Ti

Ultrafine-grained (UFG) commercially pure (CP) Ti with a grain size of about 200 nm was produced by ECAP up to 8 passes using route BC at room temperature. For ECAP processing a proper die set was designed and constructed with an internal channel angle Φ of 120° and an outer arc of curvature Ψ of 20°. Strain rate sensitivity of UFG CP-Ti and CG CP-Ti were investigated by compression tests in the temperature range of 298~673K and strain rate range of 10-4~100s-1 using Gleeble simulator machine. Evolution of the microstructure during compression testing was observed using optical microscopy (OM) and transmission electron microscopy (TEM). Strain rate sensitivity value m of the UFG CP-Ti has been measured and is found to increase with increasing temperature and decreasing strain rate, and is enhanced compared to that of CG CP-Ti. Result of the deformation activation energy determination of UFG CP-Ti indicates that the deformation mechanism in UFG CP-Ti is correlated to the grain boundaries.

scholarly journals Dynamic Mechanical Compression Impulse of Lithium-Ion Pouch Cells

Energies ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 2105 ◽  
Author(s):  
Alon Ratner ◽  
Richard Beaumont ◽  
Iain Masters
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Lithium Ion ◽  
Rate Sensitivity ◽  
Dynamic Mechanical Properties ◽  
Impact Testing ◽  
Significant Feature ◽  
Dynamic Mechanical ◽  
The Impact

Strain rate sensitivity has been widely recognized as a significant feature of the dynamic mechanical properties of lithium-ion cells, which are important for their accurate representation in automotive crash simulations. This research sought to improve the precision with which dynamic mechanical properties can be determined from drop tower impact testing through the use of a diaphragm to minimize transient shock loads and to constrain off-axis motion of the indenter, specialized impact absorbers to reduce noise, and observation of displacement with a high speed camera. Inert pouch cells showed strain rate sensitivity in an increased stiffness during impact tests that was consistent with the poromechanical interaction of the porous structure of the jellyroll with the liquid electrolyte. The impact behaviour of the inert pouch cells was similar to that of an Expanded Polypropylene foam (EPP), with the exception that the inert pouch cells did not show hysteretic recovery under the weight of the indenter. This suggests that the dynamic mechanical behaviour of the inert pouch cells is analogous to a highly damped foam.

scholarly journals Investigation of mechanical properties of limesand brick under dynamic loading

2018 ◽  
Vol 174 ◽  
pp. 02018
Author(s):  
Anatoliy Bragov ◽  
Andrey Lomunov ◽  
Alexander Konstantinov ◽  
Dmitriy Lamzin ◽  
Leopold Kruszka
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Strain Rate ◽  
Dynamic Loading ◽  
Energy Intensity ◽  
Strain Rate Range ◽  
Brazilian Test ◽  
Stress Rate ◽  
Rate Range ◽  
Kolsky Method

The results of experimental study of mechanical properties of samples of lime-sand brick under dynamic loading are presented. The tests were carried out using the traditional Kolsky method and its modification - dynamic splitting (the so-called «Brazilian test»). The laws of change in strength, strain, time properties and energy intensity of the investigated material are established in the strain rate range of 5·102-2.5·103 s-1 under compression and in the stress rate range of 2·101-3·102 GPa/s under tension.

Sign in / Sign up

Export Citation Format

Share Document