scholarly journals Eccentric Compressive Behavior of Round-Ended Rectangular Concrete-Filled Steel Tubes with Different Central Angles

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 456
Author(s):  
Zhigang Ren ◽  
Qi Li ◽  
Gaoyu Wang ◽  
Wei Wei ◽  
Mohammed A. A. M. Abbas
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Ultimate Bearing Capacity ◽  
Confinement Effect ◽  
Interfacial Stress ◽  
Steel Tubes ◽  
Cross Sectional ◽  
Aspect Ratios ◽  
Material Utilization ◽  
Concrete Filled Steel Tubes

The application of round-ended rectangular concrete-filled steel tubes (RRCFSTs) in high-rise buildings or bridge structures is increasing, improving structural performance and meeting aesthetic requirements. Researching this novel steel–concrete composite helps to fully utilize the properties of the materials. In this study, 15 specimens were tested for analysis of the behaviors of RRCFSTs with different central angles under eccentric compression. Influences of central angles of round ends (θ), aspect ratios of rectangular parts (κ), steel strength and the eccentric ratio on failure modes, material utilization, confinement effect and eccentric bearing capacity are studied. Besides, the mechanism of confinement effects of steel tubes with different θ values was evaluated with the finite element method (FEM). The results show that local bulking usually occurs at the compression zone. When θ gradually changes from 0° to 180°, the local bulking position of straight steel plate changes from mid-length to both ends of the columns. Additionally, the interfacial stress between steel tube and concrete at round ends rises, but that at the corner, it decreases continuously, which results in an improved overall confinement effect and increased material utilization. In contrast, a larger κ leads to lower material efficiency because of the reduced overall confinement effect. The increases in both θ and κ enlarge the cross-sectional area and the eccentric ultimate bearing capacity, whereas θ has a better influence on the ductility than κ. A feasible simplified calculating approach for the eccentric ultimate bearing capacity of RRCFSTs is presented and validated.

scholarly journals Behavior of the T-Shaped Concrete-Filled Steel Tubular Columns after Elevated Temperature

2021 ◽  
Vol 2021 ◽  
pp. 1-20
Author(s):  
Xianglong Liu ◽  
Jicheng Zhang ◽  
Hailin Lu ◽  
Ning Guan ◽  
Jiahao Xiao ◽  
...  
Keyword(s):  
Elevated Temperature ◽  
Bearing Capacity ◽  
Failure Modes ◽  
Shear Failure ◽  
Element Model ◽  
Ultimate Bearing Capacity ◽  
Steel Tubes ◽  
Tubular Columns ◽  
Short Columns ◽  
Experimental Values

The mechanical properties of T-shaped concrete-filled steel tubular (TCFST) short columns under axial compression after elevated temperature are investigated in this paper. A total of 30 TCFST short columns with different temperature (T), steel ratio (α), and duration of heating (t) were tested. The TCFST column was directly fabricated by welding two rectangular steel tubes together. The study mainly investigated the failure modes, the ultimate bearing capacity, the load-displacement, and the load-strain performance of the TCFST short columns. Experimental results indicate that the rectangular steel tubes of the TCFST column have deformation consistency, and the failure mode consists of local crack, drum damage, and shear failure. Additionally, the influence of high temperature on the residual bearing capacity of the TCFST is significant, e.g., a higher temperature can downgrade the ultimate bearing capacity. Finally, a finite element model (FEM) is developed to simulate the performance of the TCFST short columns under elevated temperature, and the results agree with experimental values well. Overall, this investigation can provide some guidance for future studies on damage assessment and reinforcement of the TCFST columns.

scholarly journals Experimental Investigation on Web Crippling Property of High-Strength Cold-Formed (HSCF) Rectangular Steel Tube

2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Xianglong Liu ◽  
Jicheng Zhang ◽  
Yuanqi Li ◽  
Lei Zeng ◽  
Guofeng Du
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
High Strength ◽  
Ultimate Bearing Capacity ◽  
Height Ratio ◽  
Steel Tubes ◽  
Web Crippling ◽  
Bearing Plate ◽  
Bearing Load ◽  
Plate Width

To research the web crippling performance (i.e., the ultimate web crippling bearing capacity and ductility) of high-strength cold-formed (HSCF) rectangular steel tubes under concentrated load, thirty-six specimens with different bearing plate width, width-to-height ratio, boundaries, and loading conditions are fabricated and tested in this paper. Particularly, four kinds of boundaries and loading conditions are utilized, including end-two-flange (ETF), end-one-flange (EOF), interior-two-flange (ITF), and interior-one-flange (IOF). Research revealed the failure modes of HSCF rectangular steel tubes under concentrated loads applied at the end or interior. Moreover, the load-displacement curves and load-strain curves are obtained. The results show that the ultimate crippling capacity of webs increases significantly with larger bearing plate width and width-to-height ratio. Specimens subjected to interior bearing load have higher ultimate strength and deformation capacity than counterparts that are subjected to bearing load at the end. Additionally, in the middle of the compression web, all strain measuring points enter the plasticity stage and finally appear in the plastic hinge area. Subsequently, the failure modes and ultimate bearing capacity are simulated by the finite element method (FEM), which is implemented via ABAQUS. By comparing the test results with the numerical values, demonstrate the effectiveness of the proposed numerical simulation on investigating the failure modes and the ultimate bearing capacity of HSCF rectangular steel tubes. Finally, regarding the conservative and dangerous calculation of web crippling ultimate bearing capacity in current codes, we can provide a good guidance for future work, particularly the proposed calculation equations for ultimate bearing capacity of HSCF rectangular steel tubes.

The Seismic Behavior of Strengthened Joints between Concrete-Filled Steel Tubes and Beams Based on the Numerical Simulation Technology

2010 ◽  
Vol 150-151 ◽  
pp. 571-575
Author(s):  
Yun Peng Chu ◽  
Yong Yao ◽  
Shu Lian Xiao ◽  
Yue Chen
Keyword(s):  
Energy Dissipation ◽  
Bearing Capacity ◽  
Double Layer ◽  
Seismic Behavior ◽  
Steel Tube ◽  
Ultimate Bearing Capacity ◽  
Steel Tubes ◽  
Concrete Filled Steel Tube ◽  
Energy Dissipation Capacity ◽  
Concrete Filled Steel Tubes

As a key part in concrete-filled steel tubular frames, the seismic behavior of joints between concrete-filled steel tubes and beams needs more research because of the complexity of stress under the reciprocating load. the behavior of 9 strengthened joints connecting concrete-filled steel tube with H-shaped steel beam have been analyzed under reversed cyclic loading condition by using finite element analysis software ANSYS, and the result show that: (1) The ultimate bearing capacity, energy dissipation capacity and ductility of strengthened joint are obvious better than that of ordinary welded joint; (2) Compared to concrete-filled steel tube the ultimate bearing capacity, energy dissipation capacity and ductility of double-layer concrete-filled steel tubes are better; (3) For the joints connecting double-layer concrete-filled steel tubes with beams, the shape of inner tube have certain effect on the ultimate bearing capacity but little on the energy dissipation capacity and ductility. (4) The shape of stiffened plate has significant influence on the ultimate bearing capacity, energy dissipation capacity and ductility of nodes.

Experimental Studies on Axially Loaded Concrete Columns Confined by Different Materials

2008 ◽  
Vol 400-402 ◽  
pp. 513-518 ◽  
Author(s):  
Yong Chang Guo ◽  
Pei Yan Huang ◽  
Yang Yang ◽  
Li Juan Li
Keyword(s):  
Bearing Capacity ◽  
Glass Fiber ◽  
Failure Modes ◽  
Experimental Studies ◽  
Concrete Columns ◽  
Steel Tube ◽  
Ultimate Bearing Capacity ◽  
Advantages And Disadvantages ◽  
Axially Loaded ◽  
Normal Strength

The improvement of the load carrying capacity of concrete columns under a triaxial compressive stress results from the strain restriction. Under a triaxial stress state, the capacity of the deformation of concrete is greatly decreased with the increase of the side compression. Therefore, confining the deformation in the lateral orientation is an effective way to improve the strength and ductility of concrete columns. This paper carried out an experimental investigation on axially loaded normal strength concrete columns confined by 10 different types of materials, including steel tube, glass fiber confined steel tube (GFRP), PVC tube, carbon fiber confined PVC tube (CFRP), glass fiber confined PVC tube (GFRP), CFRP, GFRP, polyethylene (PE), PE hybrid CFRP and PE hybrid GFRP. The deformation, macroscopical deformation characters, failure mechanism and failure modes are studied in this paper. The ultimate bearing capacity of these 10 types of confined concrete columns and the influences of the confining materials on the ultimate bearing capacity are obtained. The advantages and disadvantages of these 10 types of confining methods are compared.

Research of Post-Fire Mechanical Property of Steel Fiber Reinforced Ceramsite Concrete Filled Steel Tubes after Exposure to Fire

2013 ◽  
Vol 790 ◽  
pp. 181-184
Author(s):  
Hai Lun Tong ◽  
Tian Hong Wang ◽  
Jian Qi Lu ◽  
Xin Tang Wang
Keyword(s):  
Bearing Capacity ◽  
Steel Fiber ◽  
Fiber Reinforced ◽  
Fire Load ◽  
Furnace Temperature ◽  
Steel Tubes ◽  
Compression Performance ◽  
Short Columns ◽  
Maximum Value ◽  
Concrete Filled Steel Tubes

The post-fire axial compressive behavior of a set of steel fiber reinforced ceramsite concrete filled steel tubular short columns (noted as SFCC-SSC) was experimentally studied. Effect of the maximum value of fire response temperatures of the specimens and some parameters on the axial compression performance of the specimens was especially discussed. The results show that the surface of the steel tubes after fire presented dark red for 700°Cof furnace temperature and orange red for 900°C, and there was no obvious descending segment in post-fire load-displacement curves of the most specimens subjected to fire load. It was concluded that the axial bearing capacity of the specimens aftersuffering the furnace temperature of 900°C is much less than that of the specimens not subjected to fire load, and the volume of steel fiber of 0.5% of has the greatest effect on post-fire bearing capacity of specimens of SFCC-SSC.

scholarly journals Circumferential Expansion Property of Composite Wrapping System for Main Cable Protection of Suspension Bridge

2020 ◽  
Vol 2020 ◽  
pp. 1-18
Author(s):  
Pengfei Cao ◽  
Hai Fang ◽  
Weiqing Liu ◽  
Yong Zhuang ◽  
Yuan Fang ◽  
...  
Keyword(s):  
Growth Rate ◽  
Bearing Capacity ◽  
Radial Displacement ◽  
Failure Modes ◽  
Suspension Bridge ◽  
Temperature Deformation ◽  
Suspension Bridges ◽  
Cross Sectional ◽  
Main Cable ◽  
Rubber Belt

A composite wrapping system for main cable protection of suspension bridges was designed by using prepreg fiber-reinforced composites and nitrile rubber. The circumferential expansion performance of the system was tested, and the curves of circumferential bearing capacity and radial displacement of the components were obtained. Failure modes of each group of components were compared and analyzed. The results show that most of the components are vertically fractured at the lap transition. The increase of the number of prepreg layers contributed the most to the circumferential bearing capacity of components, with a growth rate of 65.31%~109.01%. The increase of rubber belt layers had the most significant effect on the radial displacement of the components, with a growth rate of 7.06%~23.5%. In the initial stage of the test, the strain of each part of the component was smaller due to the compaction by the loading device, and the strain value of the component was generally linearly increased during the loading process, during which the strain of the overlap was the smallest. The calculated cross-sectional temperature deformation of the main cable is in good agreement with the experimental data. The application of the rubber belt increases the deformation of the main cable; therefore, the protection system for the main cable could have more deformation redundancy and delay the arrival of the ultimate strain of the outer prepreg wrap.

scholarly journals Experimental Study and Theoretical Analysis on Flexural Mechanical Propertiesof Reinforced Timber Beams

2018 ◽  
Vol 27 (1) ◽  
pp. 096369351802700
Author(s):  
Xiong Xueyu ◽  
Wang Yiqingzi ◽  
Xue Rongjun ◽  
Lu Xuanxing
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Failure Modes ◽  
Theoretical Calculations ◽  
Development Trend ◽  
Ultimate Bearing Capacity ◽  
Bending Test ◽  
Element Analysis ◽  
Finite Element Software ◽  
Reinforced Beams

As Chinese architecture masterpiece, ancient Hui-style architecture is the admiration for Chinese and foreign master builders. According to the bending test, the theoretical calculations and Abaqus finite element analysis on 5 Hui-style architecture beams, this paper points out the differences between un-reinforced beams and reinforced beams on ultimate bearing capacity, deflection and other performance indicators. The reinforcement methods of embedding steel bars, embedding CFRP bars and pasting CFRP plate can respectively improve the ultimate bearing capacity by 20.2%, 32.6% and 37.0%. Based on the plane section assumption and considering thereduction of tensile strength causedby wood knots and defects in tension zone, this paper predicts failure modes of the test beams may occur, and gives the ultimate bearing capacity of different failure modes. In addition, this paper uses the Abaqus finite element software for simulating test beams, and the development trend of load-deflectioncurve between the test and numerical simulation are in good agreement, providing reference for further research of Hui-style architecture.

Ultimate Bearing Capacity of Composition Columns Reinforced with the Prefabricated SHSCUS Filled with Steel Tubes Subjected to Axial Load

2011 ◽  
Vol 368-373 ◽  
pp. 225-229
Author(s):  
Guo Can Chen ◽  
Zhi Sheng Xu ◽  
Zhi Shuo Yang
Keyword(s):  
Bearing Capacity ◽  
Load Capacity ◽  
High Strength ◽  
Ultimate Bearing Capacity ◽  
Concrete Cover ◽  
Design Rule ◽  
Superposition Method ◽  
Steel Tubes ◽  
Ultimate Load Capacity ◽  
Concrete Type

This paper presents an experimental investigation on the short composition columns reinforced with the prefabricated super high strength concrete used stone-chop(abbreviated to SHSCUS) filled with steel tubes with 1RC as reference. The experimental parameters were the concrete type inner steel tubes, and L/D ratio, steel ratio and so on. The performance of the composition columns was investigated using different diameter-to-thickness ratio of steel tubes ranging from 15 to 26.6, and different cubic strength of 126.7, 120.3, 122.4, 134.4, 125.4, 111.4, 108.6MPa of infill concrete. The experimental results showed that concrete cover falling off was prior to specimens failure, and that the design rule, as specified in current code suitable for HSC overestimate the ultimate bearing capacity, were not suitable for the case with SHSCUS. Then the hypothesis was put forward based on experimental phenomena observed, and the formula of its ultimate load capacity was suggested based on superposition method, by which the predicted values have a good coincidence with those from the experiments.

scholarly journals BUCKLING OF SLENDER COMPOSITE CONCRETE‐FILLED STEEL COLUMNS

2010 ◽  
Vol 16 (2) ◽  
pp. 230-236 ◽  
Author(s):  
C. Douglas Goode ◽  
Artiomas Kuranovas ◽  
Audronis Kazimieras Kvedaras
Keyword(s):  
Bearing Capacity ◽  
Steel Tubes ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Hollow Section ◽  
Steel Columns ◽  
Tubular Columns ◽  
Cylinder Strength ◽  
Experimental Values ◽  
Concrete Filled Steel Tubes

The paper presents the analysis of the experimental data of 1817 on concrete‐filled steel tubes ‐ CFSTs. These results are compared with the predicted results of the load‐bearing capacity of calculations of slender elements according to the methods suggested by Eurocode 4. The following types of tested CFSTs were analysed: circular and rectangular hollow section stub and long columns fully filled with concrete, which were with or without applied moments at the ends of specimen. During the results obtained in the result of the tests on the load bearing capacity for circular concrete‐filled steel tubular columns correspond with the calculated values based on methods presented by Eurocode 4. The experimental values of load bearing capacity for members of concrete‐filled rectangular hollow sections agree very well with the theoretical values where the concrete cylinder strength is below 75 N/mm2. The analysis demonstrated that preloading of concrete‐filled hollow section members does not influence the load bearing capacity. This paper also presents the examination of stress state distribution for concrete‐filled hollow section members, influence of concrete preloading and of longitudinal stress strain curves. Santrauka Straipsnyje aptariami 1817 betonšerdžiu plieniniu vamzdiniu strypu eksperimentiniai duomenys. Šie duomenys lyginami su rezultatais, gautais remiantis Eurocode 4 pateiktais kompozitiniu elementu laikomosios galios nustatymo metodais. Analizuojami tokie betonšerdžiu plieniniu strypu bandiniu tipai: pilnavidures trumpos arba liaunos apskritojo ir stačiakampio skerspjūvio vamzdines betonšerdes plienines kolonos su ju galuose veikiančiu lenkiamuoju momentu arba be jo. Apskritojo skerspjūvio betonšerdžiu kolonu bandymu metu gautieji laikomosios galios rezultatai atitinka remiantis Eurocode 4 pateiktais metodais apskaičiuotasias ju reikšmes. Stačiakampio skerspjūvio betonšerdžiu elementu laikomosios galios bandymais rastosios reikšmes labai gerai atitinka teorines reikšmes, kai šerdies betono ritininis stipris nesiekia 75 N/mm2. Analizuojant nustatyta, kad išankstinis betonšerdžiu elementu apkrovimas neturi beveik jokio poveikio elementu laikomajai galiai. Šiame straipsnyje taip pat nagrinejamas betonšerdžiu elementu itempiu būviu pasiskirstymas, betono apspaudimo poveikis bei išilginiu deformaciju ir itempiu kreives.

Experimental Study of Performance of Self-Stress Lightweight Aggregate Concrete Filled Steel Tubes after Exposure to Fire

2013 ◽  
Vol 790 ◽  
pp. 173-176
Author(s):  
Jin Can Xu ◽  
Peng Fei Ren ◽  
Hai Lun Tong ◽  
Xin Tang Wang
Keyword(s):  
Bearing Capacity ◽  
Fire Behavior ◽  
Lightweight Aggregate ◽  
Lightweight Aggregate Concrete ◽  
Fire Load ◽  
Steel Tubes ◽  
Aggregate Concrete ◽  
Expansive Agent ◽  
Short Columns ◽  
Concrete Filled Steel Tubes

The post-fire behavior of a set of self-stress lightweight aggregate concrete filled steel tubular short columns (noted as SSLC-SSC) after exposure to fire was experimentally studied. Effect of the maximum value of fire response temperatures of the tubes and their geometric parameters on the strength and the other mechanical property of the specimens were especially discussed. The experimental results show that the specimens of SSLC-SSC have higher post-fire bearing capacity and better plastic deformation, there was no obvious descent segment in post-fire load-displacement curves of the most specimens subjected to fire load. It was concluded that the maximum response temperature of specimens has great effect on the post-fire bearing capacity of self-stress concrete-filled steel tubes subjected to fire load, and the value of self-stress corresponding to 10% of dosage of expansive agent has the greatest effect on post-fire bearing capacity of specimens of SSLC-SSC.

Sign in / Sign up

Export Citation Format

Share Document