scholarly journals Comparison of CO2 Separation Efficiency from Flue Gases Based on Commonly Used Methods and Materials

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 460
Author(s):  
Zenon Ziobrowski ◽  
Adam Rotkegel
Keyword(s):  
Membrane Separation ◽  
Separation Efficiency ◽  
Activated Carbons ◽  
Packed Column ◽  
Ceramic Membranes ◽  
Flue Gases ◽  
Co2 Removal ◽  
Experimental Conditions ◽  
Column Adsorption ◽  
Supported Ionic Liquid Membranes

The comparison study of CO2 removal efficiency from flue gases at low pressures and temperatures is presented, based on commonly used methods and materials. Our own experimental results were compared and analyzed for different methods of CO2 removal from flue gases: absorption in a packed column, adsorption in a packed column and membrane separation on polymeric and ceramic membranes, as well as on the developed supported ionic liquid membranes (SILMs). The efficiency and competitiveness comparison of the investigated methods showed that SILMs obtained by coating of the polydimethylsiloxane (PDMS) membrane with 1-ethyl-3-methylimidazolium acetate ([Emim][Ac]) exhibit a high ideal CO2/N2 selectivity of 152, permeability of 2400 barrer and long term stability. Inexpensive and selective SILMs were prepared applying commercial membranes. Under similar experimental conditions, the absorption in aqueous Monoethanolamine (MEA) solutions is much faster than in ionic liquids (ILs), but gas and liquid flow rates in packed column sprayed with IL are limited due to the much higher viscosity and lower diffusion coefficient of IL. For CO2 adsorption on activated carbons impregnated with amine or IL, only a small improvement in the adsorption properties was achieved. The experimental research was compared with the literature data to find a feasible solution based on commercially available methods and materials.

scholarly journals Feasibility Study of the Application of Membrane Separation in CO2 Removal from Flue Gases.

1993 ◽  
Vol 19 (5) ◽  
pp. 714-721 ◽  
Author(s):  
Kenji Haraya ◽  
Masaru Nakaiwa ◽  
Naotsugu Itoh ◽  
Chiyoshi Kamisawa
Keyword(s):  
Feasibility Study ◽  
Membrane Separation ◽  
Flue Gases ◽  
Co2 Removal

Experimental Studies Concerning the Semipermeable Membrane Separation Efficiency for 134Cs, 137Cs, 57Co, 58Co, 60Co, 54Mn in Liquid Radioactive Waste I. Treatment of secondary waste from POD decontamination procedure

2008 ◽  
Vol 59 (5) ◽  
Author(s):  
Mirela Dulama ◽  
Nicoleta Deneanu ◽  
Cristian Dulama ◽  
Margarit Pavelescu
Keyword(s):  
Membrane Separation ◽  
Separation Efficiency ◽  
Liquid Radioactive Waste ◽  
Experimental Studies ◽  
Experimental Tests ◽  
Suspended Solid ◽  
Process Efficiency ◽  
Active Charcoal ◽  
Precipitation Process ◽  
Pre Treatment

The paper presents the experimental tests concerning the treatment by membrane techniques of radioactive aqueous waste. Solutions, which have been treated by using the bench-scale installation, were radioactive simulated secondary wastes from the decontamination process with modified POD. Generally, an increasing of the retention is observed for most of the contaminants in the reverse osmosis experiments with pre-treatment steps. The main reason for taking a chemical treatment approach was to selectively remove soluble contaminants from the waste. In the optimization part of the precipitation step, several precipitation processes were compared. Based on this comparison, mixed [Fe(CN)6]4-/Al3+/Fe2+ was selected as a precipitation process applicable for precipitation of radionuclides and flocculation of suspended solid. Increased efficiencies for cesium radionuclides removal were obtained in natural zeolite adsorption pre-treatment stages and this was due to the fact that volcanic tuff used has a special affinity for this element. Usually, the addition of powdered active charcoal serves as an advanced purifying method used to remove organic compounds and residual radionuclides; thus by analyzing the experimental data (for POD wastes) one can observe a decreasing of about 50% for cobalt isotopes subsequently to the active charcoal adsorption.. The semipermeable membranes were used, which were prepared by the researchers from the Research Center for Macromolecular Materials and Membranes, Bucharest. The process efficiency was monitored by gamma spectrometry.

Separation of Biologically Active Compounds by Membrane Operations

2017 ◽  
Vol 23 (2) ◽  
pp. 218-230 ◽  
Author(s):  
Xiaoying Zhu ◽  
Renbi Bai
Keyword(s):  
Energy Consumption ◽  
Bioactive Compounds ◽  
Membrane Fouling ◽  
Membrane Separation ◽  
Separation Efficiency ◽  
High Energy ◽  
Separation Processes ◽  
Membrane Processes ◽  
Separation Technology ◽  
Pressure Driven

Background: Bioactive compounds from various natural sources have been attracting more and more attention, owing to their broad diversity of functionalities and availabilities. However, many of the bioactive compounds often exist at an extremely low concentration in a mixture so that massive harvesting is needed to obtain sufficient amounts for their practical usage. Thus, effective fractionation or separation technologies are essential for the screening and production of the bioactive compound products. The applicatons of conventional processes such as extraction, distillation and lyophilisation, etc. may be tedious, have high energy consumption or cause denature or degradation of the bioactive compounds. Membrane separation processes operate at ambient temperature, without the need for heating and therefore with less energy consumption. The “cold” separation technology also prevents the possible degradation of the bioactive compounds. The separation process is mainly physical and both fractions (permeate and retentate) of the membrane processes may be recovered. Thus, using membrane separation technology is a promising approach to concentrate and separate bioactive compounds. Methods: A comprehensive survey of membrane operations used for the separation of bioactive compounds is conducted. The available and established membrane separation processes are introduced and reviewed. Results: The most frequently used membrane processes are the pressure driven ones, including microfiltration (MF), ultrafiltration (UF) and nanofiltration (NF). They are applied either individually as a single sieve or in combination as an integrated membrane array to meet the different requirements in the separation of bioactive compounds. Other new membrane processes with multiple functions have also been developed and employed for the separation or fractionation of bioactive compounds. The hybrid electrodialysis (ED)-UF membrane process, for example has been used to provide a solution for the separation of biomolecules with similar molecular weights but different surface electrical properties. In contrast, the affinity membrane technology is shown to have the advantages of increasing the separation efficiency at low operational pressures through selectively adsorbing bioactive compounds during the filtration process. Conclusion: Individual membranes or membrane arrays are effectively used to separate bioactive compounds or achieve multiple fractionation of them with different molecule weights or sizes. Pressure driven membrane processes are highly efficient and widely used. Membrane fouling, especially irreversible organic and biological fouling, is the inevitable problem. Multifunctional membranes and affinity membranes provide the possibility of effectively separating bioactive compounds that are similar in sizes but different in other physical and chemical properties. Surface modification methods are of great potential to increase membrane separation efficiency as well as reduce the problem of membrane fouling. Developing membranes and optimizing the operational parameters specifically for the applications of separation of various bioactive compounds should be taken as an important part of ongoing or future membrane research in this field.

scholarly journals Application of Bar Adsorptive Microextraction for the Determination of Levels of Tricyclic Antidepressants in Urine Samples

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3101
Author(s):  
Mariana N. Oliveira ◽  
Oriana C. Gonçalves ◽  
Samir M. Ahmad ◽  
Jaderson K. Schneider ◽  
Laiza C. Krause ◽  
...  
Keyword(s):  
Tricyclic Antidepressants ◽  
Matrix Effects ◽  
Activated Carbons ◽  
Process Efficiency ◽  
Gas Chromatography Mass Spectrometry ◽  
Selected Ion Monitoring ◽  
Experimental Conditions ◽  
Analytical Methodology ◽  
Low Efficiency

This work entailed the development, optimization, validation, and application of a novel analytical approach, using the bar adsorptive microextraction technique (BAμE), for the determination of the six most common tricyclic antidepressants (TCAs; amitriptyline, mianserin, trimipramine, imipramine, mirtazapine and dosulepin) in urine matrices. To achieve this goal, we employed, for the first time, new generation microextraction devices coated with convenient sorbent phases, polymers and novel activated carbons prepared from biomaterial waste, in combination with large-volume-injection gas chromatography-mass spectrometry operating in selected-ion monitoring mode (LVI-GC-MS(SIM)). Preliminary assays on sorbent coatings, showed that the polymeric phases present a much more effective performance, as the tested biosorbents exhibited low efficiency for application in microextraction techniques. By using BAμE coated with C18 polymer, under optimized experimental conditions, the detection limits achieved for the six TCAs ranged from 0.2 to 1.6 μg L−1 and, weighted linear regressions resulted in remarkable linearity (r2 > 0.9960) between 10.0 and 1000.0 μg L−1. The developed analytical methodology (BAμE(C18)/LVI-GC-MS(SIM)) provided suitable matrix effects (90.2–112.9%, RSD ≤ 13.9%), high recovery yields (92.3–111.5%, RSD ≤ 12.3%) and a remarkable overall process efficiency (ranging from 84.9% to 124.3%, RSD ≤ 13.9%). The developed and validated methodology was successfully applied for screening the six TCAs in real urine matrices. The proposed analytical methodology proved to be an eco-user-friendly approach to monitor trace levels of TCAs in complex urine matrices and an outstanding analytical alternative in comparison with other microextraction-based techniques.

Dynamic separation and recovery of osmium using γ-nano-Al2O3 in a packed column adsorption system

2015 ◽  
Vol 42 (3) ◽  
pp. 2691-2705
Author(s):  
Lijun Yang ◽  
Lian He ◽  
Xiaojun Chu ◽  
Fang Wang ◽  
Lei Zhang
Keyword(s):  
Packed Column ◽  
Adsorption System ◽  
Column Adsorption

Biosorption of uranium(VI) from aqueous solution by biomass of brown algae Laminaria japonica

2014 ◽  
Vol 70 (1) ◽  
pp. 136-143 ◽  
Author(s):  
K. Y. Lee ◽  
K. W. Kim ◽  
Y. J. Baek ◽  
D. Y. Chung ◽  
E. H. Lee ◽  
...  
Keyword(s):  
Particle Size ◽  
Brown Algae ◽  
Activated Carbons ◽  
Laminaria Japonica ◽  
Limiting Factor ◽  
Stable Operation ◽  
Experimental Conditions ◽  
Wastewater Treatment Process ◽  
Radioactive Wastewater ◽  
Ionic Diffusivity

The uranium(VI) adsorption efficiency of non-living biomass of brown algae was evaluated in various adsorption experimental conditions. Several different sizes of biomass were prepared using pretreatment and surface-modification steps. The kinetics of uranium uptake were mainly dependent on the particle size of the prepared Laminaria japonica biosorbent. The optimal particle size, contact time, and injection amount for the stable operation of the wastewater treatment process were determined. Spectroscopic analyses showed that uranium was adsorbed in the porous inside structure of the biosorbent. The ionic diffusivity in the biomass was the dominant rate-limiting factor; therefore, the adsorption rate was significantly increased with decrease of particle size. From the results of comparative experiments using the biosorbents and other chemical adsorbents/precipitants, such as activated carbons, zeolites, and limes, it was demonstrated that the brown algae biosorbent could replace the conventional chemicals for uranium removal. As a post-treatment for the final solid waste reduction, the ignition treatment could significantly reduce the weight of waste biosorbents. In conclusion, the brown algae biosorbent is shown to be a favorable adsorbent for uranium(VI) removal from radioactive wastewater.

scholarly journals Tunning CO2 Separation Performance of Ionic Liquids through Asymmetric Anions

Molecules ◽  
2022 ◽  
Vol 27 (2) ◽  
pp. 413
Author(s):  
Bruna F. Soares ◽  
Daniil R. Nosov ◽  
José M. Pires ◽  
Andrey A. Tyutyunov ◽  
Elena I. Lozinskaya ◽  
...  
Keyword(s):  
Ionic Liquids ◽  
Atmospheric Pressure ◽  
Time Lag ◽  
Gas Permeation ◽  
Separation Performance ◽  
Experimental Conditions ◽  
Feed Pressure ◽  
Similar Chemical ◽  
Supported Ionic Liquid Membranes ◽  
Gas Separation Performance

This work aims to explore the gas permeation performance of two newly-designed ionic liquids, [C2mim][CF3BF3] and [C2mim][CF3SO2C(CN)2], in supported ionic liquid membranes (SILM) configuration, as another effort to provide an overall insight on the gas permeation performance of functionalized-ionic liquids with the [C2mim]+ cation. [C2mim][CF3BF3] and [C2mim][CF3SO2C(CN)2] single gas separation performance towards CO2, N2, and CH4 at T = 293 K and T = 308 K were measured using the time-lag method. Assessing the CO2 permeation results, [C2mim][CF3BF3] showed an undermined value of 710 Barrer at 293.15 K and 1 bar of feed pressure when compared to [C2mim][BF4], whereas for the [C2mim][CF3SO2C(CN)2] IL an unexpected CO2 permeability of 1095 Barrer was attained at the same experimental conditions, overcoming the results for the remaining ILs used for comparison. The prepared membranes exhibited diverse permselectivities, varying from 16.9 to 22.2 for CO2/CH4 and 37.0 to 44.4 for CO2/N2 gas pairs. The thermophysical properties of the [C2mim][CF3BF3] and [C2mim][CF3SO2C(CN)2] ILs were also determined in the range of T = 293.15 K up to T = 353.15 K at atmospheric pressure and compared with those for other ILs with the same cation and anion’s with similar chemical moieties.

scholarly journals New extraction techniques on bioseparations: 2. Pertraction, direct extraction

2004 ◽  
Vol 58 (12) ◽  
pp. 535-547
Author(s):  
Anca-Irina Galaction ◽  
Dan Cascaval
Keyword(s):  
Mathematical Models ◽  
Carboxylic Acids ◽  
Separation Efficiency ◽  
Extraction Techniques ◽  
Direct Extraction ◽  
Experimental Conditions ◽  
Maximum Separation

The second part of this review presents our original results on the separation of some biosynthetic products (antibiotics, carboxylic acids, alcohols) by pertraction and direct extraction from broths without biomass filtration. For the analyzed systems, the experimental conditions required for reaching maximum separation efficiency and the mathematical models describing the process have been established. For all the studied cases, these extraction techniques simplify the technologies and reduce the overall cost of the product.

scholarly journals Fabrication, Properties, Performances, and Separation Application of Polymeric Pervaporation Membranes: A Review

Polymers ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 1466 ◽  
Author(s):  
Luchen Wang ◽  
Yan Wang ◽  
Lianying Wu ◽  
Gang Wei
Keyword(s):  
Chemical Engineering ◽  
Environmental Science ◽  
Membrane Separation ◽  
Separation Efficiency ◽  
Low Cost ◽  
Composite Membranes ◽  
High Energy ◽  
Polymeric Membranes ◽  
Food Science ◽  
Preparation Methods

Membrane separation technologies have attracted great attentions in chemical engineering, food science, analytical science, and environmental science. Compared to traditional membrane separation techniques like reverse osmosis (RO), ultrafiltration (UF), electrodialysis (ED) and others, pervaporation (PV)-based membrane separation shows not only mutual advantages such as small floor area, simplicity, and flexibility, but also unique characteristics including low cost as well as high energy and separation efficiency. Recently, different polymer, ceramic and composite membranes have shown promising separation applications through the PV-based techniques. To show the importance of PV for membrane separation applications, we present recent advances in the fabrication, properties and performances of polymeric membranes for PV separation of various chemicals in petrochemical, desalination, medicine, food, environmental protection, and other industrial fields. To promote the easy understanding of readers, the preparation methods and the PV separation mechanisms of various polymer membranes are introduced and discussed in detail. This work will be helpful for developing novel functional polymer-based membranes and facile techniques to promote the applications of PV techniques in different fields.

Sign in / Sign up

Export Citation Format

Share Document