scholarly journals Microstructure and Texture Evolution with Relation to Mechanical Properties of Compared Symmetrically and Asymmetrically Cold Rolled Aluminum Alloy

Metals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 156 ◽  
Author(s):  
Jakob Kraner ◽  
Peter Fajfar ◽  
Heinz Palkowski ◽  
Goran Kugler ◽  
Matjaž Godec ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Electron Backscatter Diffraction ◽  
Texture Evolution ◽  
Strain Ratio ◽  
Tensile Tests ◽  
Asymmetric Rolling ◽  
Plastic Strain Ratio ◽  
Rolled Aluminum ◽  
The Impact

The impact of asymmetric cold rolling was quantitatively assessed for an industrial aluminum alloy AA 5454. The asymmetric rolling resulted in lower rolling forces and higher strains compared to conventional symmetric rolling. In order to demonstrate the positive effect on the mechanical properties with asymmetric rolling, tensile tests, plastic-strain-ratio tests and hardness measurements were conducted. The improvements to the microstructure and the texture were observed with a light and scanning electron microscope; the latter making use of electron-backscatter diffraction. The result of the asymmetric rolling was a much lower planar anisotropy and a more homogeneous metal sheet with finer grains after annealing to the soft condition. The increased isotropy of the deformed and annealed aluminum sheet is a product of the texture heterogeneity and reduced volume fractions of separate texture components.

Effect of Nb and V in the Development of Texture and Plastic Strain Ratio in Low Carbon Microalloyed Steels Produced by A.S.T. Technology

2005 ◽  
Vol 500-501 ◽  
pp. 279-286
Author(s):  
Carlo Mapelli ◽  
Roberto Venturini ◽  
Antonio Guindani
Keyword(s):  
Mechanical Properties ◽  
Strain Ratio ◽  
Tensile Tests ◽  
Microalloyed Steels ◽  
Low Carbon ◽  
Plastic Strain Ratio ◽  
Steel Technology ◽  
Back Scattering ◽  
Carbon Microalloyed ◽  
Hot Rolled

The effects of Nb and V on the anisotropy and textures featuring the hot rolled low carbon microalloyed steels produced by A.S.T. (Arvedi Steel Technology) have been studied as a function of the final coiling temperatute Tcoiling. Mechanical properties and r-values for twelve steels have been determined through tensile tests performed on three main different directions: 0°, 45°, 90° to the rolling one. The samples have been analysed by EBSD (Electron Back Scattering Diffraction) to identify the textures developed during the process. The relations among the chemical composition of the steels (i.e. C, N, Nb, V contents), the mechanical properties, the temperature during the coiling operations, the textures and the formability properties have been pointed out.

scholarly journals Effects of Initial Precipitate on Shear Deformation during Asymmetric Rolling of Al-Mg-Si Alloy: Texture and Formability

2020 ◽  
Vol 58 (10) ◽  
pp. 703-714
Author(s):  
Wonkee Chae ◽  
Bong-Kyu Kim ◽  
Jongbeom Lee ◽  
Jun Hyun Han
Keyword(s):  
Shear Deformation ◽  
Room Temperature ◽  
Tensile Deformation ◽  
Texture Evolution ◽  
Plastic Anisotropy ◽  
Rolling Direction ◽  
Strain Ratio ◽  
Equivalent Strain ◽  
Asymmetric Rolling ◽  
Plastic Strain Ratio

Al-Mg-Si alloy was rolled asymmetrically at several temperatures to apply shear deformation, and the effects of the initial precipitate on shear deformation, texture evolution, formability, and plastic anisotropy were studied. Texture was analyzed using a EBSD, and the formability and plastic anisotropy of the specimen were evaluated using the value and value calculated from the plastic strain ratio (r-value) which was determined from the change in the length of the specimen during tensile deformation. Asymmetric rolling induces a larger equivalent strain than symmetric rolling, and the equivalent strain increases as the asymmetric rolling temperature increases. When a specimen with peak-aged initial precipitates was asymmetrically rolled, less shear deformation occurred at room temperature than in a solution-treated specimen without initial precipitates. In contrast, a larger shear deformation occurred at high temperatures (500°C). With asymmetric rolling at room temperature, the specimens without initial precipitates had higher formability and lower plasticity, while for asymmetric rolling at high temperature, the specimens with initial precipitates had higher formability and lower plastic anisotropy. This is due to the <111>//ND texture, such as {111}<110> and {111}<112> orientation that has similar and high r-values at 0°, 45°, and 90° to the rolling direction, developed by the shear deformation that occurred during asymmetric rolling.

Development of Asymmetric Rolling for the Better Control over Structure and Mechanical Properties in IF Steel

2012 ◽  
Vol 706-709 ◽  
pp. 2788-2793 ◽  
Author(s):  
Dmitry Orlov ◽  
Rimma Lapovok ◽  
László S. Tóth ◽  
Ilana B. Timokhina ◽  
Peter D. Hodgson ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Electron Backscatter Diffraction ◽  
Tensile Tests ◽  
Experimental Investigations ◽  
If Steel ◽  
Asymmetric Rolling ◽  
Electron Backscatter ◽  
Strain Components ◽  
Backscatter Diffraction ◽  
Crystallographic Orientations

In the present study, the effects of kinematic and geometric asymmetries in rolling during multi-pass processing of IF steel are examined. The theoretical investigation by final element simulations and experimental investigations by means of electron-backscatter diffraction analysis and tensile tests suggest that asymmetric rolling increases the total imposed strain compared to symmetric rolling, and largely re-distributes the strain components due to additional shear. This enhances the intensity of grain refinement, strengthens and tilts crystallographic orientations, and increases mechanical strength. The effect is highest in the asymmetric rolling with differential roll diameters.

Corrosion damage evolution of the aircraft aluminum alloy 2024 T3

2016 ◽  
Vol 7 (1) ◽  
pp. 25-46 ◽  
Author(s):  
Spiros Pantelakis ◽  
Dorothea Setsika ◽  
Apostolos Chamos ◽  
Anna Zervaki
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Damage Evolution ◽  
Structural Integrity ◽  
Corrosion Damage ◽  
Tensile Tests ◽  
Content Type ◽  
Experimental Database ◽  
Aluminum Alloy 2024 ◽  
The Impact

Purpose – The purpose of this paper is to quantify the corrosion damage evolution that has occurred on the aircraft aluminum alloy 2024 after the exposure to Exfoliation Corrosion Test (EXCO) solution. Moreover, the effect of the evolving corrosion damage on the materials mechanical properties has been assessed. The relevance of the corrosion damage induced by the exposure to the laboratory EXCO for linking it to the damage developed after the exposure of the material on several outdoor corrosive environments or in service is discussed. Design/methodology/approach – To induce corrosion damage the EXCO has been used. For the quantification of corrosion damage the metallographic features considered have been pit depth, diameter, pitting density and pit shape. The effect of the evolving corrosion damage on the materials mechanical properties has been assessed by means of tensile tests on pre corroded specimens. Findings – The results have shown that corrosion damage starts from pitting and evolves to exfoliation, after the development of intergranular corrosion. This evolution is expressed by the increase of the depth of attack, as well as through the significant growth of the diameter of the damaged areas. The results of the tensile tests performed on pre corroded material made an appreciable decrease of the materials tensile properties evident. The decrease of the tensile ductility may become dramatic and increases on severity with increasing corrosion exposure time. SEM fractography revealed a quasi-cleavage zone beneath the depth of corrosion attack. Originality/value – The results underline the impact of corrosion damage on the mechanical behavior of the aluminum alloy 2024 T3 and demonstrate the need for further investigation of the corrosion effect on the structural integrity of the material. This work provides an experimental database concerning the quantification of corrosion damage evolution and the loss of material properties due to corrosion.

scholarly journals Effect of a Continuous Annealing Temperature on the Microstructure, Mechanical Properties and Texture of Annealed Drawn and Ironed Plate

Crystals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1569
Author(s):  
Zhiying Mo ◽  
Xiaohong Chu ◽  
Pengfei Gao ◽  
Dengcui Yang ◽  
Heng Cui ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Annealing Temperature ◽  
Electron Backscatter Diffraction ◽  
Weighted Average ◽  
Strain Ratio ◽  
Continuous Annealing ◽  
Plastic Strain Ratio ◽  
Average Grain Size ◽  
Lower Temperature ◽  
Backscatter Diffraction

To improve the production process and produce high-quality annealed drawn and ironed (DI) plate, continuous annealing experiments were carried out at 620 °C, 640 °C, 680 °C, and 720 °C, and the effect of a continuous annealing temperature on the microstructure, mechanical characteristics, and texture of annealed DI plate were clarified. The microstructure was tested with a scanning electron microscope (SEM); the mechanical properties and weighted average of the plastic strain ratio (r¯) were measured using a tension test; and the texture characterizations were tested by X-ray powder diffractometer (XRD) and electron backscatter diffraction (EBSD). The results reveal that, with the increase of the annealing temperature, the average grain size grew from 5.14 μm to 6.56 μm, the yield strength and tensile strength decreased, and the elongation increased. The rolling textures drastically reduced after annealing. When annealed at a lower temperature of 620 °C, the texture content of {111} <110> was the highest. When the annealing temperature increased to 640 °C, 680 °C and 720 °C, the texture content of {111} <112> was higher than that of {111} <110>. The mechanical properties of the DI plate that was annealed at 640 °C are the best, with a higher r¯ value and a lower planar anisotropy value.

scholarly journals Investigation on Fracture of a 6014-T4 Aluminum Alloy Sheet in the Flanging and Hemming Process Based on Numerical and Experimental Methods

Metals ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 81
Author(s):  
Zhengwei Gu ◽  
Gang Wang ◽  
Ge Yu
Keyword(s):  
Aluminum Alloy ◽  
Uniform Elongation ◽  
Natural Aging ◽  
Strain Ratio ◽  
Tensile Tests ◽  
Alloy Sheet ◽  
Uniaxial Tensile ◽  
Strain Hardening Exponent ◽  
Plastic Strain Ratio ◽  
Aging Period

The fracture of a flat-surface straight-edge hemmed component of aluminum alloy sheets was investigated in this study. The specimen was made of 1 mm thick 6014-T4. Natural aging characteristics of 6014-T4 were studied via uniaxial tensile tests. The results show that the yield stress and ultimate tensile strength increased while the uniform elongation, strain hardening exponent, and plastic strain ratio decreased during the natural aging period, which worsened the formability. The sheet was biaxially stretched to obtain a pre-strain before the flanging and hemming operation. The influence of the flanging radius on the fracture was evaluated using experimental and numerical methods, and the optimum values were obtained. The comparison between the roller hemming and die hemming process proved that the former tends to produce better formability.

scholarly journals Strength Enhancement of Superduplex Stainless Steel Using Thermomechanical Processing

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1094
Author(s):  
M. A. Lakhdari ◽  
F. Krajcarz ◽  
J. D. Mithieux ◽  
H. P. Van Landeghem ◽  
M. Veron
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Thermomechanical Processing ◽  
Tensile Tests ◽  
Image Correlation ◽  
Strength Enhancement ◽  
Industrial Material ◽  
Superduplex Stainless Steel ◽  
The Impact ◽  
Strength Improvement

The impact of microstructure evolution on mechanical properties in superduplex stainless steel UNS S32750 (EN 1.4410) was investigated. To this end, different thermomechanical treatments were carried out in order to obtain clearly distinct duplex microstructures. Optical microscopy and scanning electron microscopy, together with texture measurements, were used to characterize the morphology and the preferred orientations of ferrite and austenite in all microstructures. Additionally, the mechanical properties were assessed by tensile tests with digital image correlation. Phase morphology was not found to significantly affect the mechanical properties and neither were phase volume fractions within 13% of the 50/50 ratio. Austenite texture was the same combined Goss/Brass texture regardless of thermomechanical processing, while ferrite texture was mainly described by α-fiber orientations. Ferrite texture and average phase spacing were found to have a notable effect on mechanical properties. One of the original microstructures of superduplex stainless steel obtained here shows a strength improvement by the order of 120 MPa over the industrial material.

scholarly journals Mechanical Properties of Spruce Wood Extracted from GLT Beams Loaded by Fire

2021 ◽  
Vol 13 (10) ◽  
pp. 5494
Author(s):  
Lucie Kucíková ◽  
Michal Šejnoha ◽  
Tomáš Janda ◽  
Jan Sýkora ◽  
Pavel Padevět ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Cross Section ◽  
Negative Impact ◽  
Tensile Tests ◽  
Thermal Recovery ◽  
Bending Test ◽  
Small Scale ◽  
Spruce Wood ◽  
The Impact

Heating wood to high temperature changes either temporarily or permanently its physical properties. This issue is addressed in the present contribution by examining the effect of high temperature on residual mechanical properties of spruce wood, grounding on the results of full-scale fire tests performed on GLT beams. Given these tests, a computational model was developed to provide through-thickness temperature profiles allowing for the estimation of a charring depth on the one hand and on the other hand assigning a particular temperature to each specimen used subsequently in small-scale tensile tests. The measured Young’s moduli and tensile strengths were accompanied by the results from three-point bending test carried out on two groups of beams exposed to fire of a variable duration and differing in the width of the cross-section, b=100 mm (Group 1) and b=160 mm (Group 2). As expected, increasing the fire duration and reducing the initial beam cross-section reduces the residual bending strength. A negative impact of high temperature on residual strength has also been observed from simple tensile tests, although limited to a very narrow layer adjacent to the charring front not even exceeding a typically adopted value of the zero-strength layer d0=7 mm. On the contrary, the impact on stiffness is relatively mild supporting the thermal recovery property of wood.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

Sign in / Sign up

Export Citation Format

Share Document