scholarly journals A Novel Approach by Spark Plasma Sintering to the Improvement of Mechanical Properties of Titanium Carbonitride-Reinforced Alumina Ceramics

Molecules ◽  
2021 ◽  
Vol 26 (5) ◽  
pp. 1344
Author(s):  
Magdalena Szutkowska ◽  
Marcin Podsiadło ◽  
Tomasz Sadowski ◽  
Paweł Figiel ◽  
Marek Boniecki ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Spark Plasma Sintering ◽  
Vickers Hardness ◽  
Titanium Carbonitride ◽  
Plasma Sintering ◽  
Novel Approach ◽  
Zirconia Composites ◽  
Spark Plasma ◽  
Higher Temperature

Ti(C,N)-reinforced alumina-zirconia composites with different ratios of C to N in titanium carbonitride solid solutions, such as Ti(C0.3,N0.7) (C:N = 30:70) and Ti(C0.5,N0.5) (C:N = 50:50), were tested to improve their mechanical properties. Spark plasma sintering (SPS) with temperatures ranging from 1600 °C to 1675 °C and pressureless sintering (PS) with a higher temperature of 1720 °C were used to compare results. The following mechanical and physical properties were determined: Vickers hardness, Young’s modulus, apparent density, wear resistance, and fracture toughness. A composite with the addition of Ti(C0.5,N0.5)n nanopowder exhibited the highest Vickers hardness of over 19.0 GPa, and its fracture toughness was at 5.0 Mpa·m1/2. A composite with the Ti(C0.3,N0.7) phase was found to have lower values of Vickers hardness (by about 10%), friction coefficient, and specific wear rate of disc (Wsd) compared to the composite with the addition of Ti(C0.5,N0.5). The Vickers hardness values slightly decreased (from 5% to 10%) with increasing sintering temperature. The mechanical properties of the samples sintered using PS were lower than those of the samples that were spark plasma sintered. This research on alumina–zirconia composites with different ratios of C to N in titanium carbonitride solid solution Ti(C,N), sintered using an unconventional SPS method, reveals the effect of C/N ratios on improving mechanical properties of tested composites. X-ray analysis of the phase composition and an observation of the microstructure was carried out.

Effects of Milling Time on Microstructure and Mechanical Properties of Composite WC-(Fe3Al-B) Consolidated by Spark Plasma Sintering

2017 ◽  
Vol 899 ◽  
pp. 487-492
Author(s):  
Luis Antonio C. Ybarra ◽  
Afonso Chimanski ◽  
Gilberto J. Pereira ◽  
Izabel Fernanda Machado ◽  
Humberto Naoyuki Yoshimura
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Spark Plasma Sintering ◽  
Vickers Hardness ◽  
Milling Time ◽  
Iron Aluminide ◽  
Plasma Sintering ◽  
Hard Metals ◽  
Spark Plasma ◽  
Vibration Milling

Cobalt is widely used to produce WC-Co hard metals, but this binder has problems of shortage and unstable price. In this work, cobalt was replaced by an iron aluminide intermetallic binder. WC-10%(Fe3Al-3%B) composite was prepared by vibration milling of WC, Fe, Fe-B, and Al powders and sintered by spark plasma sintering (SPS) at 1150 °C for 8 min under 30 MPa. The milling time was 0.17, 12, 25 and 50 h. The SPS was efficient to consolidate the composite resulting in relative density of ~98% or higher. With increasing milling time, Vickers hardness (HV30) of composite increased from 12 to 14 GPa due to the enhanced homogeneity of microstructure, while the fracture toughness, KIc, determined by an indention fracture method using Shetty equation, remained constant at around 9.1 MPa.m1/2.

Synthesis, Microstructure and Mechanical Properties of ZrB2 Ceramic Prepared by Mechanical Alloying and Spark Plasma Sintering

2010 ◽  
Vol 434-435 ◽  
pp. 165-168 ◽  
Author(s):  
Chun Feng Hu ◽  
Yoshio Sakka ◽  
Tetsuo Uchikoshi ◽  
Tohru Suzuki ◽  
Byung Koog Jang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Mechanical Alloying ◽  
Relative Density ◽  
Heating Rate ◽  
Spark Plasma Sintering ◽  
Vickers Hardness ◽  
Heating Rates ◽  
Plasma Sintering ◽  
Spark Plasma

Dense bulk ZrB2 ceramic was synthesized by mechanical alloying (MA) and followed spark plasma sintering (SPS) using zirconium and boron as initial materials. It was found that MA process was effective to fragment the coarse metal zirconium particles from 45 m to less than 1 m within 20 hours. In comparison with the commercial ZrB2 powder, the as-obtained zirconium and boron mixture powders showed higher sinterability. When the sintering was carried out at 1800oC, the relative density of synthesized ZrB2 samples using mixture powder was above 95%, higher than that of ZrB2 sample prepared using commercial powder (73%). Vickers hardness of those ZrB2 samples was at the same level of 15 GPa. However, the fracture toughness of ZrB2 samples seemed to depend on the heating rate of the SPS process. Corresponding to the heating rates of 10, 50, and 100oC/min, the fracture toughness of as-prepared ZrB2 samples were 3.83, 3.19, and 2.74 MPa•m1/2, respectively.

Mechanical Properties of ZrO2 (Y2O3)-Al2O3 Nanocomposites with Addition of Hydroxyapatite Prepared by Spark Plasma Sintering

2009 ◽  
Vol 631-632 ◽  
pp. 413-423 ◽  
Author(s):  
Shu Feng Li ◽  
Hiroshi Izui ◽  
Michiharu Okano ◽  
Wei Hua Zhang ◽  
Taku Watanabe
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Spark Plasma Sintering ◽  
Vickers Hardness ◽  
Volume Fraction ◽  
Sintering Temperature ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Hardness Values

TZP-3Y20A/HA composites with addition of different volume fraction of hydroxyapatite (HA) were fabricated successfully using spark plasma sintering (SPS). The densification behavior and mechanical properties of composites are investigated as a function of sintering temperature and HA content respectively. The density of TZP-3Y20A composite increases steadily with temperature and a maximum value of 97.8% is obtained after sintering at 1400°C. Sintering the TZP-3Y20A/HA composites at 1400°C led to the decomposition of HA in the samples. Flexural strength, fracture toughness and Vickers hardness values increase with increasing sintering temperature, show decrease trend with increasing of HA content at the same temperature. They compared well with densities obtained at different sintering temperature. The maximum flexural strength, fracture toughness and Vickers hardness of 967.1 MPa, 5.27 MPam1/2 and 13.26 GPa were achieved for TZP-3Y20A composite respectively. Flexural strength, fracture toughness and Vickers hardness values of TZP-3Y20A/HA composite fell within the value range of dense HA and of TZP-3Y20A composite.

Microstructure and Mechanical Properties of Spark-Plasma-Sintered SiC-TiC Composites

2005 ◽  
Vol 287 ◽  
pp. 335-339 ◽  
Author(s):  
Kyeong Sik Cho ◽  
Kwang Soon Lee
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Heating Rate ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Applied Pressure ◽  
Argon Atmosphere ◽  
Full Density ◽  
Plasma Sintering ◽  
Spark Plasma

Rapid densification of the SiC-10, 20, 30, 40wt% TiC powder with Al, B and C additives was carried out by spark plasma sintering (SPS). In the present SPS process, the heating rate and applied pressure were kept at 100°C/min and at 40 MPa, while the sintering temperature varied from 1600-1800°C in an argon atmosphere. The full density of SiC-TiC composites was achieved at a temperature above 1800°C by spark plasma sintering. The 3C phase of SiC in the composites was transformed to 6H and 4H by increasing the process temperature and the TiC content. By tailoring the microstructure of the spark-plasma-sintered SiC-TiC composites, their toughness could be maintained without a notable reduction in strength. The strength of 720 MPa and the fracture toughness of 6.3 MPa·m1/2 were obtained in the SiC-40wt% TiC composite prepared at 1800°C for 20 min.

scholarly journals Co-Ni-Zn Ferrites Fabricated by Spark Plasma Sintering

2019 ◽  
Vol 64 (2) ◽  
pp. 265-270
Author(s):  
Andrea Balla ◽  
János Moczó ◽  
Zoltán Károly
Keyword(s):  
Mechanical Properties ◽  
Aqueous Solution ◽  
Fracture Toughness ◽  
Spark Plasma Sintering ◽  
Precipitation Method ◽  
Ferrite Powder ◽  
Alumina Film ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Reference Samples

Ni0,4Co0,2Zn0,4Fe2O4 spinel ferrites have been synthesized by precipitation method from an aqueous solution and bulk samples were fabricated by Spark Plasma Sintering (SPS) to investigate the microstructure and the mechanical properties. Although SPS is considered as a rapid compaction technique, its application is uncommon for ferrites due to reactions occurring between the graphite die and the ferrite powder at elevated temperature. In our tests this problem was circumvented by an alumina film applied on the die. We found that both chemical and phase composition could be retained in the sintered specimens after sintering. In addition, they exhibited improved mechanical properties in terms of hardness (10 GPa) and fracture toughness (2.7 MPa · m−1/2) as compared to conventionally sintered reference samples.

Mechanical properties of stainless steel composites with titanium carbonitride consolidated by spark plasma sintering

2015 ◽  
Vol 50 (12) ◽  
pp. 1567-1572
Author(s):  
Bunyod Allabergenov ◽  
Oybek Tursunkulov ◽  
Amir Abidov ◽  
Soon-Wook Jeong ◽  
Sungjin Kim
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Spark Plasma Sintering ◽  
Titanium Carbonitride ◽  
Plasma Sintering ◽  
Spark Plasma

Preparation and Properties of β-SiAlON-cBN Composites Using Y2O3, B2O3 and Al as Additives

2014 ◽  
Vol 602-603 ◽  
pp. 380-383
Author(s):  
Chao He ◽  
Xiao Fei Shi ◽  
Xin Yan Yue ◽  
Jiang Jun Wang ◽  
Hong Qiang Ru
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Relative Density ◽  
Spark Plasma Sintering ◽  
Crack Deflection ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Microstructures And Mechanical Properties

SiAlON-cBN composites with different contents of cBN were consolidated by spark plasma sintering (SPS) at 1450°C using Y2O3, B2O3 and Al as additives. The effect of cBN content on the density, phase compositions, microstructures and mechanical properties of β-SiAlON-cBN composites was investigated. With increasing the cBN content, the density and hardness of β-SiAlON-cBN composites decreased. Fracture toughness could increase thanks to the crack deflection resulted from the cBN particles. For β-SiAlON-10 wt% cBN composites, the optimum hardness and highest relative density were 13 GPa and 96.4 %, respectively. For β-SiAlON-40 wt% cBN composites, the highest fracture toughness was KIC = 5.3 MPa∙m1/2.

scholarly journals Spark plasma sintering of Si3N4/multilayer graphene composites

2014 ◽  
Vol 13 (1) ◽  
Author(s):  
Eszter Bódis ◽  
Orsolya Tapasztó ◽  
Zoltán Károly ◽  
Péter Fazekas ◽  
Szilvia Klébert ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Silicon Nitride ◽  
Spark Plasma Sintering ◽  
Multilayer Graphene ◽  
Plasma Sintering ◽  
Spark Plasma

AbstractMulitlayer graphene reinforced silicon nitride composites were prepared by spark plasma sintering to investigate the effect of the graphene addition on mechanical properties. The composites contained multilayer graphene (MLG) in various (0, 1, 3 and 5 wt%) content. Significantly higher fracture toughness of 8.0 MPa m

scholarly journals Effect of Additive Ti3SiC2 Content on Mechanical Properties of B4C–TiB2 Composites Ceramics Sintered by Spark Plasma Sintering

2020 ◽  
Author(s):  
Xingheng Yan ◽  
Xingui Zhou ◽  
Honglei Wang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Spark Plasma Sintering ◽  
Bending Strength ◽  
High Fracture Toughness ◽  
Transgranular Fracture ◽  
Composite Ceramics ◽  
High Fracture ◽  
Plasma Sintering ◽  
Spark Plasma

Abstract B4C-TiB2 composite ceramics with ultra-high fracture toughness were successfully prepared via spark plasma sintering at 1900℃ using B4C and Ti3SiC2 as raw materials. The results show that compared with pure B4C ceramics sintered by SPS, the hardness of B4C-TiB2 composite ceramics is decreased, but the flexural strength and fracture toughness are significantly improved, especially the fracture toughness has been improved by leaps and bounds. When the content of Ti3SiC2 is 30vol.%, the B4C-TiB2 composite ceramic has the best comprehensive mechanical properties: hardness, bending strength and fracture toughness are 27.28 GPa, 405.11 MPa and 18.94 MPa·m1/2, respectively. The fracture mode of the B4C-TiB2 composite ceramics is a mixture of transgranular fracture and intergranular fracture. Two main two reasons for the ultra-high fracture toughness are the existence of lamellar graphite at the grain boundary, and the formation of a three-dimensional interpenetrating network covering the whole composite.

Sign in / Sign up

Export Citation Format

Share Document