scholarly journals Experimental Investigation of Thermal and Pressure Performance in Computer Cooling Systems Using Different Types of Nanofluids

Nanomaterials ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 1231 ◽  
Author(s):  
Alfaryjat ◽  
Miron ◽  
Pop ◽  
Apostol ◽  
Stefanescu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Base Fluid ◽  
Pumping Power ◽  
Cooling Systems

A modern computer generates a great amount of heat while working. In order to secure appropriate working conditions by extracting the heat, a specific mechanism should be used. This research paper presents the effect of nanofluids on the microchannel heat sink performance of computer cooling systems experimentally. CeO2, Al2O3 and ZrO2 nanoparticles suspended in 20% ethylene glycol and 80% distilled water are used as working fluids in the experiment. The concentration of the nanoparticles ranges from 0.5% to 2%, mass flow rate ranges from 0.028 kg/s to 0.084 kg/s, and the ambient temperature ranges from 25 °C to 40 °C. Regarding the thermal component, parameters such as thermophysical properties of the nanofluids and base fluids, central processing unit (CPU) temperature, heat transfer coefficient, pressure drop, and pumping power have been experimentally investigated. The results show that CeO2-EG/DW, at a concentration of 2% and a mass flow rate of 0.084 kg/s, has with 8% a lower temperature than the other nanofluids and with 29% a higher heat transfer coefficient compared with the base fluid. The Al2O3-EG/DW shows the lowest pressure drop and pumping power, while the CeO2-EG/DW and ZrO2-EG/DW show the highest. However, a slight increase of pumping power and pressure drop can be accepted, considering the high improvement that the nanofluid brings in computer cooling performance compared to the base fluid.

scholarly journals Effect of nanofluid properties and mass-flow rate on heat transfer of parabolic-trough concentrating solar system

2019 ◽  
Vol 16 (1) ◽  
pp. 33-44 ◽  
Author(s):  
M.K. Islam ◽  
Md. Hasanuzzaman ◽  
N.A. Rahim ◽  
A. Nahar
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Laminar Flow ◽  
Turbulent Flow ◽  
Transfer Coefficient ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Parabolic Trough ◽  
Concentrated Solar Energy

Sustainable power generation, energy security, and global warming are the big challenges to the world today. These issues may be addressed through the increased usage of renewable energy resources and concentrated solar energy can play a vital role in this regard. The performance of a parabolic-trough collector’s receiver is here investigated analytically and experimentally using water based and therminol-VP1based CuO, ZnO, Al2O3, TiO2, Cu, Al, and SiC nanofluids. The receiver size has been optimized by a simulation program written in MATLAB. Thus, numerical results have been validated by experimental outcomes under same conditions using the same nanofluids. Increased volumetric concentrations of nanoparticle is found to enhance heat transfer, with heat transfer coefficient the maximum in W-Cu and VP1-SiC, the minimum in W-TiO2 and VP1-ZnO at 0.8 kg/s flow rate. Changing the mass flow rate also affects heat transfer coefficient. It has been observed that heat transfer coefficient reaches its maximum of 23.30% with SiC-water and 23.51% with VP1-SiC when mass-flow rate is increased in laminar flow. Heat transfer enhancement drops during transitions of flow from laminar to turbulent. The maximum heat transfer enhancements of 9.49% and 10.14% were achieved with Cu-water and VP1-SiC nanofluids during turbulent flow. The heat transfer enhancements of nanofluids seem to remain constant when compared with base fluids during either laminar flow or turbulent flow.

Fluid Flow and Heat Transfer Characteristics of Slug Bubbly Flow in Micro Condensers

2007 ◽  
Author(s):  
J. S. Hu ◽  
Christopher Y. H. Chao
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Flow Pattern ◽  
Mass Flow ◽  
Flow Rate ◽  
Bubbly Flow ◽  
Mixed Flow

Experiments were carried out to study the condensation flow pattern in silicon micro condenser using water as medium. Five flow patterns were identified under our experimental conditions. Slug-bubbly flow and droplet/liquid slug flow were found to be the two dominant flows in the micro condenser. These two flow patterns subsequently determined the heat transfer and pressure drop properties of the fluid. It was observed that only slug-bubbly flow existed in low steam mass flow and high heat flux conditions. When the steam mass flow rate increased or the heat flux dropped, mixed flow pattern occurred. An empirical correlation was obtained to predict when the transition of the flow pattern from slug-bubbly flow to mixed flow could appear. In the slug-bubbly flow regime, heat transfer coefficient and pressure drop in the micro condensers were studied. It was found that micro condensers with smaller channels could exhibit higher heat transfer coefficient and pressure drop. At constant heat flux, increasing the steam mass flow rate resulted in a higher heat transfer coefficient and also the pressure drop.

scholarly journals Experimental Investigation Of Heat Transfer Characteristics Of Nanofluid Using Parallel Flow, Counter Flow And Shell And Tube Heat Exchanger

2015 ◽  
Vol 62 (4) ◽  
pp. 509-522 ◽  
Author(s):  
R. Dharmalingam ◽  
K.K. Sivagnanaprabhu ◽  
J. Yogaraja ◽  
S. Gunasekaran ◽  
R. Mohan
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Tube Heat Exchanger ◽  
Overall Heat Transfer Coefficient ◽  
Shell And Tube

Abstract Cooling is indispensable for maintaining the desired performance and reliability over a very huge variety of products like electronic devices, computer, automobiles, high power laser system etc. Apart from the heat load amplification and heat fluxes caused by many industrial products, cooling is one of the major technical challenges encountered by the industries like manufacturing sectors, transportation, microelectronics, etc. Normally water, ethylene glycol and oil are being used as the fluid to carry away the heat in these devices. The development of nanofluid generally shows a better heat transfer characteristics than the water. This research work summarizes the experimental study of the forced convective heat transfer and flow characteristics of a nanofluid consisting of water and 1% Al2O3 (volume concentration) nanoparticle flowing in a parallel flow, counter flow and shell and tube heat exchanger under laminar flow conditions. The Al2O3 nanoparticles of about 50 nm diameter are used in this work. Three different mass flow rates have been selected and the experiments have been conducted and their results are reported. This result portrays that the overall heat transfer coefficient and dimensionless Nusselt number of nanofluid is slightly higher than that of the base liquid at same mass flow rate at same inlet temperature. From the experimental result it is clear that the overall heat transfer coefficient of the nanofluid increases with an increase in the mass flow rate. It shows that whenever mass flow rate increases, the overall heat transfer coefficient along with Nusselt number eventually increases irrespective of flow direction. It was also found that during the increase in mass flow rate LMTD value ultimately decreases irrespective of flow direction. However, shell and tube heat exchanger provides better heat transfer characteristics than parallel and counter flow heat exchanger due to multi pass flow of nanofluid. The overall heat transfer coefficient, Nusselt number and logarithmic mean temperature difference of the water and Al2O3 /water nanofluid are also studied and the results are plotted graphically.

scholarly journals Numerical Study on Regenerative Cooling Characteristics of Kerosene Scramjets

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Xuan Jin ◽  
Chibing Shen ◽  
Xianyu Wu
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Fluid Velocity ◽  
Regenerative Cooling ◽  
Outlet Pressure

The use of kerosene-based regenerative cooling for scramjet has been found widespread attention due to its inherent nature of high energy utilization efficiency and good thermal protection performance. In order to provide a reference for the later design and experiments, three-dimensional turbulence simulations and sensitivity analysis were performed to determine the effects of three operating mode parameters, heat flux, mass flow rate, and outlet pressure, on the regenerative cooling characteristics of kerosene scramjets. A single rectangular-shaped channel for regenerative cooling was assumed. The RNG k-ε turbulence model and kerosene cracking mechanism with single-step global reaction were applied for the supercritical-pressure heat transfer of kerosene flows in the channel. Conclusions can be drawn that as the kerosene temperature rises along the channel, the decrease of fluid density and viscosity contributes to increasing the fluid velocity and heat transfer. When the kerosene temperature is close to the pseudocritical temperature, the pyrolysis reaction results into the rapid increase of fluid velocity. However, the heat transfer deterioration occurs as the specific heat and thermal conductivity experience their turning points. The higher heat flux leads to lower heat transfer coefficient, and the latter stops rising when the wall temperature reaches the pseudocritical temperature. The same rising trend of the heat transfer coefficient is observed under different outlet pressures, but the heat transfer deterioration occurs earlier at smaller outlet pressure for the reason that the corresponding pseudocritical temperature decreases. The heat transfer coefficient increases significantly along with the rise of the mass flow rate, which is mainly attributable to the increase of Reynolds number. Quantitative results indicate that as the main influence factors, the heat flux and mass flow rate are respectively negatively and positively relative to the intensification of heat transfer, but outlet pressure always has little effects on cooling performance.

The Simulation of Boiling Heat Transfer in Metal Foam Tube

2013 ◽  
Vol 448-453 ◽  
pp. 3312-3315
Author(s):  
Bin Sun ◽  
Bin Bin Cui ◽  
Chao Liang
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Boiling Heat Transfer ◽  
Metal Foam ◽  
Vapor Quality ◽  
The Heat Transfer Coefficient

A three-dimensional physical mode of metal foam tube was built by CFD software. The Brinkman-Forchheimer extended Darcy equation and user-defined function (UFD) of the mass transfer and energy transfer between vapor phase and liquid phase compiled by C language were used in the simulation of boiling heat transfer in metal foam tube. The results show that, at a given mass flow rate, the pressure drop nonlinearly increases as the vapor quality rises; At the low mass flow rate, with the increasing of vapor quality, the flow pattern is transferred to wavy flow from stratified flow and then transfer to stratified wavy flow, while the heat transfer coefficient decreases with the increasing of vapor quality. At the high mass flow rate, with the increasing of vapor quality, the flow pattern is transferred to annular flow from slug flow, while the heat transfer coefficient increases with the increasing of vapor quality. The simulation results agree well with the experimental data.

Detailed Flow Analyses Through Crossover Holes Between Two Adjacent Rib-Roughened Cooling Channels and the Resulting Impingement Heat Transfer

2018 ◽  
Author(s):  
Fei Xue ◽  
Mohammad E. Taslim
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Mass Flow ◽  
Flow Rate ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Impingement Heat Transfer

Impingement cooling in airfoils cooling cavities, solely or combined with film and convective cooling, is a common practice in gas turbines. Depending on the cooling cavity design, the mass flow rate through individual crossover holes could vary significantly in the flow direction thus creating jets of different strengths in the target cavity. This jet flow variation, in turn, creates an impingement heat transfer coefficient variation along the channel. A test section, simulating two adjacent cooling cavities on the trailing side of an airfoil, is made up of two channels with trapezoidal cross-sectional areas. On the partition wall between the two channels, eleven crossover holes create the jets. Two distinct exit flow arrangements are investigated — a) jets, after interaction with the target surface, are turned towards the target channel exit axially and b) jets are exited from a row of racetrack-shaped slots along the target channel. Flow measurements are reported for individual holes and heat transfer coefficients on the eleven target walls downstream the jets are measured using the steady-state liquid crystal thermography technique. Smooth as well as rib-roughened target surfaces with four rib geometries (0°,45°, 90° and 135° rib angles) are tested. Correlations are developed for mass flow rate through each crossover hole for cases with different number of crossover holes, based on the pressure drop across the holes. Heat transfer coefficient variations along the target channel for all rib geometries and flow conditions are reported for a range of 5000 to 50000 local jet Reynolds numbers. Major conclusions of this study are: 1) A correlation is developed to successfully predict the mass flow rates through individual crossover holes for geometries with six to eleven crossover holes, based on the pressure drop across the holes, 2) impingement heat transfer coefficient correlates well with the local jet Reynolds number for both exit flow arrangements, and 3) the case of axial flow in the target channel exiting from the channel end, at higher jet Reynolds numbers, produced higher heat transfer coefficients than those in the case of flow exiting through a row of slots along the target channel opposite to the crossover holes.

Investigations on the Effect of Blade Angle on Ventilated Brake Disc Using CFD

2005 ◽  
Author(s):  
Kannan M. Munisamy ◽  
Hanan Mokhtar ◽  
Hasril Hasini ◽  
Mohd Zamri Yusof ◽  
Mohd Azree Idris
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Linear Trend ◽  
Brake Disc ◽  
Blade Angle ◽  
Flow And Heat Transfer

This paper presents the investigation on the effect of blade angle to the mass flow and heat transfer coefficient of a ventilated brake disc. Six different blade angle configurations are simulated using commercial computational fluid dynamics code, FLUENT. Important parameters such as mass flow rate of air through the ventilated blade and surface heat transfer coefficient are predicted and analyzed. Prediction shows reasonable estimation of mass flow rate and heat transfer coefficient on the disc brake. Linear trend is achieved on the mass flow and heat transfer coefficient as the vehicle speed increases. It is also concluded that the optimum mass flow and heat transfer coefficient are predicted at blade angle of 15°. The prediction provides an insight into the behavior of the air flow through the restricted passage of the brake disc design.

scholarly journals Optimization of Shell and Tube Condenser for Low Temperature Thermal Desalination Plant

2021 ◽  
Vol 309 ◽  
pp. 01011
Author(s):  
R Elakkiyadasan ◽  
Kumar P Manoj ◽  
M Subramanian ◽  
N Balaji ◽  
M Karthick ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Mass Flow Rate ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Pumping Power ◽  
Overall Heat Transfer Coefficient ◽  
Shell And Tube

In the current work, attempt for enhancing the heat exchanger of the shell and tube by analyzing the various parameters. The heat exchanger is a device used to transfer heat between at least two fluids. In the different kinds of heat exchangers utilized in various industries, shell and tube heat exchangers are presumably the most adaptable and widely heat exchangers utilized in most industrial areas. Based on the relationship between different parameters such as tube velocity, overall heat transfer coefficient, mass flow rate, and pumping power, analysis is carried out. Results show that the tube velocity increases the overall heat transfer coefficient, total pressure drop and mass flow rate of water, Pumping Power, up to the certain limit and starts to decrease. So that the parameters can be optimized by conducting the experiments based on different input parameters. The parameters which influence the optimal result are researched and recommended.

Sign in / Sign up

Export Citation Format

Share Document