scholarly journals Bi1−xEuxFeO3 Powders: Synthesis, Characterization, Magnetic and Photoluminescence Properties

Nanomaterials ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1465 ◽  
Author(s):  
Vasile-Adrian Surdu ◽  
Roxana Doina Trușcă ◽  
Bogdan Ștefan Vasile ◽  
Ovidiu Cristian Oprea ◽  
Eugenia Tanasă ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Bismuth Ferrite ◽  
Sol Gel ◽  
Magnetic Behavior ◽  
Weak Ferromagnetism ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Characteristic Emission ◽  
Gel Technique ◽  
Comparative Results

Europium substituted bismuth ferrite powders were synthesized by the sol-gel technique. The precursor xerogel was characterized by thermal analysis. Bi1−xEuxFeO3 (x = 0–0.20) powders obtained after thermal treatment of the xerogel at 600 °C for 30 min were investigated by X-ray diffraction (XRD), scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), Raman spectroscopy, and Mössbauer spectroscopy. Magnetic behavior at room temperature was tested using vibrating sample magnetometry. The comparative results showed that europium has a beneficial effect on the stabilization of the perovskite structure and induced a weak ferromagnetism. The particle size decreases after the introduction of Eu3+ from 167 nm for x = 0 to 51 nm for x = 0.20. Photoluminescence spectroscopy showed the enhancement of the characteristic emission peaks intensity with the increase of Eu3+ concentration.

Evaluation of Novel Nanophase Ce0.8Sr0.2Fe0.9Ir0.1O3-δ as Cathode Material for Low Temperature SOFC

2016 ◽  
Vol 44 ◽  
pp. 35-50 ◽  
Author(s):  
Chima Benjamin Njoku ◽  
Patrick Gathura Ndungu
Keyword(s):  
Electron Microscopy ◽  
Solid Oxide Fuel Cells ◽  
Cathode Material ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Low Temperature Sofc ◽  
Gel Technique ◽  
Perovskite Type ◽  
A Current

In this study, Ce0.8Sr0.2Fe0.9Ir0.1O3-δ (CSFI) perovskite type material was prepared by sol-gel technique, characterised, and then tested as a cathode material for solid oxide fuel cells operating between 300 – 500 °C. The materials were studied using X-ray diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The morphology was examined using scanning electron microscopy and high resolution transmission electron microscopy. Samples showed changes in the overall structure and defect chemistry with an increase in calcination temperature. When tested as cathode materials, the material calcined at 1000 °C had the greatest performance at a test temperature of 500 °C, with a current density of 774.47 mA/cm2, a power density of 483.07 mW/cm2 and an area specific resistance (ASR) of 0.342 Ω/cm2.

Nanostructured red-emitting MgGa2O4:Eu3+ phosphors

2004 ◽  
Vol 19 (5) ◽  
pp. 1504-1508 ◽  
Author(s):  
Bin-Siang Tsai ◽  
Yen-Hwei Chang ◽  
Yu-Chung Chen
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sol Gel ◽  
Photoluminescence Intensity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Gel Technique ◽  
Red Luminescence ◽  
20 Nm

Nano-grained phosphors of Eu3+-doped MgGa2O4 crystallites were prepared by sol-gel technique. The characterization and optical properties of luminescent MgGa2O4:Eu3+ powders have been investigated. The dried sol-gel powders were calcined in air at different temperature from 600 to 1000 °C for 5 h. The x-ray diffraction profiles showed that the MgGa2O4:Eu3+ powders began to crystallize around 600 °C and formed stable MgGa2O4 phase in the temperature range of 600–900 °C. The transmission electron microscopy morphology observations revealed that the fired powders exhibit small grain size less than 20 nm. In the PL studies, under ultraviolet (394 nm) excitation, the calcined powders emitted bright red luminescence (615 nm, 5D0→7F2), and the powders fired at 900 °C were found to have the maximum photoluminescence intensity. The quenching concentration of Eu3+ in MgGa2O4 crystallites was also indicated to be about 5∼6 mol%.

scholarly journals Bactericidal Activity of TiO2on Cells ofPseudomonas aeruginosaATCC 27853

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
J. L. Aguilar Salinas ◽  
J. R. Pacheco Aguilar ◽  
S. A. Mayén Hernández ◽  
J. Santos Cruz
Keyword(s):  
Electron Microscopy ◽  
Pseudomonas Aeruginosa ◽  
Uv Light ◽  
Light Exposure ◽  
Sol Gel ◽  
Titanium Isopropoxide ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Gel Technique ◽  
Short Time

The photocatalytic activity of semiconductors is increasingly being used to disinfect water, air, soils, and surfaces. Titanium dioxide (TiO2) is widely used as a photocatalyst in thin films, powder, and in mixtures with other semiconductors or metals. This work presents the antibacterial effects of TiO2and light exposure (at 365 nm) onPseudomonas aeruginosaATCC 27853. TiO2powder was prepared from a mixture of titanium isopropoxide, ethanol, and nitric acid using a green and short time sol-gel technique. The obtained gel annealed at 450°C was characterized by X-ray diffraction, Raman spectroscopy, ultraviolet-visible spectroscopy, diffuse reflectance, scanning electron microscopy, and transmission electron microscopy. The nanocomposite effectively catalyzed the inactivation ofPseudomonas aeruginosa. Following 90 minutes exposure to TiO2and UV light, logarithm of cell density was reduced from 6 to 3. These results were confirmed by a factorial design incorporating two experimental replicates and two independent factors.

scholarly journals Effect of Eu3+ Concentration on the BaAl2O4/CaAl4O7: x% Eu3+ (0 ≤ x ≤ 5.5) Mixed-Phase Nanophosphors Synthesized Using Citrate Sol-Gel Method

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Bamba Mahman ◽  
Mpho Enoch Sithole
Keyword(s):  
Electron Microscopy ◽  
Sol Gel ◽  
Mixed Phase ◽  
Nanometer Scale ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Structure Morphology ◽  
Crystallite Sizes ◽  
Gel Technique

A series of undoped mixed-phase BaAl2O4/CaAl4O7 (hereafter called BC) and doped BC: x% Eu3+ (0 < x ≤ 5.5) nanophosphors were successfully prepared by the citrate sol-gel technique. Their structure, morphology, and optical properties were studied in detail by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and photoluminescence (PL) spectroscopy. XRD and SEM showed that all the BC:x% Eu3+ samples consisted of the crystalline structure of the mixed phases of both the BaAl2O4 and CaAl4O7 materials. The structure resembles more that of the BaAl2O4 than the CaAl4O7 phase. The TEM results suggest that the crystallite sizes are in the nanometer scale with rod-like particles. PL results showed multiple emission peaks located at 436, 590, 616, 656, and 703 nm, which were assigned to the intrinsic defects within the BC matrix, 5D0 ⟶ 7F1, 5D0 ⟶ 7F2, 5D0 ⟶ 7F3, and 5D0 ⟶ 7F4 transitions of Eu3+, respectively. The decay curves evidently showed that the nanophosphors have persistent luminescence. The Commission Internationale de l’Eclairage (CIE) analysis revealed that doping has tuned the emission colour from blue to orange-red. The results indicate that the Eu3+-doped samples can potentially be used in the orange/red-emitting phosphors.

Synthesis, Characterization, and Microwave Absorption Properties of SrFe12O19 Ferrites and FeNi3 Nanoplatelets Composites

2010 ◽  
Vol 148-149 ◽  
pp. 893-896 ◽  
Author(s):  
Ze Yang Zhang ◽  
Xiang Xuan Liu ◽  
You Peng Wu
Keyword(s):  
Electron Microscopy ◽  
Microwave Absorption ◽  
Composite Coatings ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Absorption Properties ◽  
Filling Fraction ◽  
Microwave Absorption Properties ◽  
Phase Reduction ◽  
Transmission Electron

M-typical SrFe12O19 ferrites and FeNi3 nanoplatelets were successfully prepared by the sol-gel method and solution phase reduction method, respectively. The crystalline and morphology of particles were studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The composite coatings with SrFe12O19 ferrites and FeNi3 nanoplatelets in polyvinylchloride matrix were prepared. The microwave absorption properties of these coatings were investigated in 2-18GHz frequency range. The results showed that the M-typical SrFe12O19 ferrites and FeNi3 nanoplatelets were obtained and they presented irregular sheet shapes. With the increase of the coating thickness, the absorbing peak value moves to the lower frequency. The absorbing peak values of the wave increase along with the increasing of the content of FeNi3 nanoplatelets filling fraction. When 40% SrFe12O19 ferrites is doped with 20% mass fraction FeNi3 nanoplatelets to prepare composite with 1.5mm thickness, the maximum reflection loss is -24.8 dB at 7.9GHz and the -10 dB bandwidth reaches 3.2GHz.

scholarly journals Magnetic PbFe12O19-TiO2 nanocomposites and their photocatalytic performance in the removal of toxic pollutants

2018 ◽  
Vol 41 (3-4) ◽  
pp. 53-62 ◽  
Author(s):  
Behnaz Lahijani ◽  
Kambiz Hedayati ◽  
Mojtaba Goodarzi
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Performance ◽  
Sol Gel ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Gel Method ◽  
Sol Gel Method ◽  
Photocatalytic Effect ◽  
Transmission Electron ◽  
Ultraviolet Light Irradiation

Abstract In this work, the PbFe12O19 nanoparticles were prepared by the simple and optimized precipitation method with different organic surfactants and capping agents. In the next step, the TiO2 nanoparticles were synthesized using the sol-gel method. At the final step, the PbFe12O19-TiO2 nanocomposites were prepared via the sol-gel method. The effect of the precipitating agent on the morphology and particle size of the products was investigated. The prepared products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and Fourier transform infrared spectroscopy. The results obtained by the vibrating sample magnetometer show the magnetic properties of the ferrite nanostructures. The photocatalytic effect of the PbFe12O19-TiO2 nanocomposite on the elimination of the azo dyes (acid black, acid violet and acid blue) under ultraviolet light irradiation was evaluated. The results indicate that the prepared nanocomposites have acceptable magnetic and photocatalytic performance.

Photocatalytic Activity of Bismuth Ferrite Nanoparticles Synthesized via Sol-Gel Route

2019 ◽  
Vol 233 (5) ◽  
pp. 595-607 ◽  
Author(s):  
Mohsin Siddique ◽  
Noor Muhammad Khan ◽  
Muhammad Saeed
Keyword(s):  
Visible Light ◽  
Photocatalytic Degradation ◽  
Irradiation Time ◽  
Bismuth Ferrite ◽  
Sol Gel ◽  
Reaction System ◽  
Light Conditions ◽  
X Ray Diffraction ◽  
Light Region ◽  
Gel Technique

Abstract Nanosized, magnetically separable bismuth ferrite (BFO) nanoparticles, pertaining a crystallite size in the range of 14–15 nm were prepared via facile sol-gel technique. The product was characterized by scanning electron microscopy, X-ray diffraction, and Fourier-transform infrared spectroscopy. The product was explored for the photocatalytic mineralization of rhodamine B (RB) dye in aqueous medium. The effect of different investigational parameters such as amount of photocatalyst, initial dye concentration and irradiation time on the photocatalytic degradation of RB was studied. The results reveal that the catalyst shows good degrading ability under normal pH and visible light conditions. BFO nanoparticles demonstrated a strong absorption ability in the visible-light region, which lead to efficient photocatalytic degradation of RB dye The reaction system was heterogeneous in nature in which the catalyst can be separated by a normal magnet.

Sol-gel processing of nanocrystalline haematite thin films

1997 ◽  
Vol 12 (6) ◽  
pp. 1441-1444 ◽  
Author(s):  
L. Armelao ◽  
A. Armigliato ◽  
R. Bozio ◽  
P. Colombo
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Raman Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Single Particles ◽  
X Ray ◽  
Transmission Electron ◽  
Gel Processing

The microstructure of Fe2O3 sol-gel thin films, obtained from Fe(OCH2CH3)3, was investigated by x-ray diffraction (XRD), transmission electron microscopy (TEM), and Raman spectroscopy. Samples were nanocrystalline from 400 °C to 1000 °C, and the crystallized phase was haematite. In the coatings, the α–Fe2O3 clusters were dispersed as single particles in a network of amorphous ferric oxide.

scholarly journals Fabrication of TiO2Nanotanks Embedded in a Nanoporous Alumina Template

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
C. Massard ◽  
S. Pairis ◽  
V. Raspal ◽  
Y. Sibaud ◽  
K. O. Awitor
Keyword(s):  
Electron Microscopy ◽  
Sol Gel ◽  
Thermal Treatments ◽  
X Ray Diffraction ◽  
Alumina Template ◽  
Nanoporous Alumina ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Sol Gel Process

The feasibility of surface nanopatterning with TiO2nanotanks embedded in a nanoporous alumina template was investigated. Self-assembled anodized aluminium oxide (AAO) template, in conjunction with sol gel process, was used to fabricate this nanocomposite object. Through hydrolysis and condensation of the titanium alkoxide, an inorganic TiO2gel was moulded within the nanopore cavities of the alumina template. The nanocomposite object underwent two thermal treatments to stabilize and crystallize the TiO2. The morphology of the nanocomposite object was characterized by Field Emission Scanning Electron Microscopy (FESEM). The TiO2nanotanks obtained have cylindrical shapes and are approximately 69 nm in diameter with a tank-to-tank distance of 26 nm. X-ray diffraction analyses performed by Transmission Electron Microscopy (TEM) with selected area electron diffraction (SAED) were used to investigate the TiO2structure. The optical properties were studied using UV-Vis spectroscopy.

Sign in / Sign up

Export Citation Format

Share Document