scholarly journals Effect of Printing Process Parameters on the Shape Transformation Capability of 3D Printed Structures

Polymers ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 117
Author(s):  
Matej Pivar ◽  
Diana Gregor-Svetec ◽  
Deja Muck
Keyword(s):  
3D Printing ◽  
Process Parameters ◽  
Active Material ◽  
Hot Water ◽  
Shape Transformation ◽  
Printing Process ◽  
Speed Flow ◽  
Layer Structures ◽  
3D Printed ◽  
Active Segment

The aim of our research was to investigate and optimise the main 3D printing process parameters that directly or indirectly affect the shape transformation capability and to determine the optimal transformation conditions to achieve predicted extent, and accurate and reproducible transformations of 3D printed, shape-changing two-material structures based on PLA and TPU. The shape-changing structures were printed using the FDM technology. The influence of each printing parameter that affects the final printability of shape-changing structures is presented and studied. After optimising the 3D printing process parameters, the extent, accuracy and reproducibility of the shape transformation performance for four-layer structures were analysed. The shape transformation was performed in hot water at different activation temperatures. Through a careful selection of 3D printing process parameters and transformation conditions, the predicted extent, accuracy and good reproducibility of shape transformation for 3D printed structures were achieved. The accurate deposition of filaments in the layers was achieved by adjusting the printing speed, flow rate and cooling conditions of extruded filaments. The shape transformation capability of 3D printed structures with a defined shape and defined active segment dimensions was influenced by the relaxation of compressive and tensile residual stresses in deposited filaments in the printed layers of the active material and different activation temperatures of the transformation.

scholarly journals Comparison between Tests and Simulations Regarding Bending Resistance of 3D Printed PLA Structures

Polymers ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 4371
Author(s):  
Dorin-Ioan Catana ◽  
Mihai-Alin Pop ◽  
Denisa-Iulia Brus
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Process Parameters ◽  
Bending Stress ◽  
Test Results ◽  
Printing Process ◽  
Simulation Process ◽  
Bending Resistance ◽  
3D Printed

Additive manufacturing is one of the technologies that is beginning to be used in new fields of parts production, but it is also a technology that is constantly evolving, due to the advances made by researchers and printing equipment. The paper presents how, by using the simulation process, the geometry of the 3D printed structures from PLA and PLA-Glass was optimized at the bending stress. The optimization aimed to reduce the consumption of filament (material) simultaneously with an increase in the bending resistance. In addition, this paper demonstrates that the simulation process can only be applied with good results to 3D printed structures when their mechanical properties are known. The inconsistency of printing process parameters makes the 3D printed structures not homogeneous and, consequently, the occurrence of errors between the test results and those of simulations become natural and acceptable. The mechanical properties depend on the values of the printing process parameters and the printing equipment because, in the case of 3D printing, it is necessary for each combination of parameters to determine their mechanical properties through specific tests.

Effects of Extrusion Temperature and Printing Direction in Bioprinting on Profile Accuracy of 3D Printed Constructs

2019 ◽  
Author(s):  
Ketan Thakare ◽  
Xingjian Wei ◽  
Hongmin Qin ◽  
Zhijian Pei
Keyword(s):  
Statistical Analysis ◽  
3D Printing ◽  
Process Parameters ◽  
Dimensional Accuracy ◽  
Extrusion Temperature ◽  
Printing Process ◽  
3D Printed ◽  
Printing Direction ◽  
Profile Accuracy

Abstract In extrusion-based bioprinting, 3D printing process parameters affect dimensional accuracy of printed constructs. However, little information is currently available on effects of extrusion temperature and printing direction on dimensional accuracy of 3D printed constructs using Alginate:Methylcelluolose hydrogel. In this study, strand thickness of 3D printed constructs printed at temperature of 35°C, 40°C, 45°C and at vertical and horizontal printing direction were measured. The statistical analysis revealed that extrusion temperature and printing direction have significant effect on the strand thickness of 3D printed constructs.

A hybrid multi-objective optimization of 3D printing process parameters using genetic algorithm

2021 ◽  
Author(s):  
Zahoor Ahmed Shariff ◽  
Lokesh M. ◽  
K. Mayandi ◽  
A. K. Saravanan ◽  
P. Sethu Ramalingam ◽  
...  
Keyword(s):  
Genetic Algorithm ◽  
3D Printing ◽  
Process Parameters ◽  
Multi Objective Optimization ◽  
Printing Process ◽  
Multi Objective

On effect of chemical-assisted mechanical blending of barium titanate and graphene in PVDF for 3D printing applications

2020 ◽  
pp. 089270572094537
Author(s):  
Ravinder Sharma ◽  
Rupinder Singh ◽  
Ajay Batish
Keyword(s):  
Mechanical Properties ◽  
Barium Titanate ◽  
3D Printing ◽  
Comparative Study ◽  
Process Parameters ◽  
Processing Temperature ◽  
Melt Mixing ◽  
Twin Screw ◽  
3D Printed ◽  
The Comparative Study

The polyvinylidene difluoride + barium titanate (BaTiO3) +graphene composite (PBGC) is one of the widely explored thermoplastic matrix due to its 4D capabilities. The number of studies has been reported on the process parameters of twin-screw extruder (TSE) setup (as mechanical blending technique) for the development of PBGC in 3D printing applications. But, hitherto, little has been reported on chemical-assisted mechanical blending (CAMB) as solution mixing and melt mixing technique combination for preparation of PBGC. In this work, for preparation of PBGC feedstock filaments, CAMB has been used. Also, the effect of process parameters of TSE on the mechanical, dimensional, morphological, and thermal properties of prepared filament of PBGC have been explored followed by 3D printing. Further, a comparative study has been reported for the properties of prepared filaments with mechanically blended composites. Similarly, the mechanical properties of 3D printed parts of chemically and mechanically blended composites have been compared. The results of tensile testing for CAMB of PBGC show that the filament prepared with 15% BaTiO3 is having maximum peak strength 43.00 MPa and break strength 38.73 MPa. The optical microphotographs of the extruded filaments revealed that the samples prepared at 180°C extruder temperature and 60 r/min screw speed have minimum porosity, as compared to filaments prepared at high extruder temperature. Further, the results of the comparative study revealed that the filaments of CAMB composites show better mechanical properties as compared to the filaments of mechanically mixed composites. However, the dimensional properties were almost similar in both cases. It was also found that the CAMB composites have better properties at low processing temperature, whereas mechanically blended composites show better results at a higher temperature. While comparing 3D printed parts, tensile strength of specimens fabricated from CAMB was more than the mechanically blended PBGC.

scholarly journals A Systematic Review of the Clinical Value and Applications of Three-Dimensional Printing in Renal Surgery

2019 ◽  
Vol 8 (7) ◽  
pp. 990 ◽  
Author(s):  
Catalina Lupulescu ◽  
Zhonghua Sun
Keyword(s):  
Systematic Review ◽  
3D Printing ◽  
Renal Disease ◽  
User Satisfaction ◽  
Surgical Simulation ◽  
Case Reports ◽  
Time Duration ◽  
Printing Process ◽  
Estimated Blood Loss ◽  
3D Printed

The purpose of this systematic review is to collate and analyse the current literature which examines clinical applications of 3D printing for renal disease, alongside cost and time duration factors associated with the printing process. A comprehensive search of the literature was performed across five different databases to identify studies that qualitatively and quantitatively assessed the value of 3D-printed kidney models for renal disease. Twenty-seven studies met the selection criteria for inclusion in the review. Twenty-five were original studies, and two were case reports. Of the 22 studies reporting a qualitative evaluation, the analysis of findings demonstrated the value of the 3D-printed models in areas of clinician and patient education, and pre-surgical simulation for complex cases of renal disease. Of five studies performing a quantitative analysis, the analysis of results displayed a high level of spatial and anatomical accuracy amongst models, with benefits including reducing estimated blood loss and risk of intra-operative complications. Fourteen studies evaluated manufacturing costs and time duration, with costs ranging from USD 1 to 1000 per model, and time duration ranging from 15 min to 9 days. This review shows that the use of customised 3D-printed models is valuable in the education of junior surgeons as well as the enhancement of operative skills for senior surgeons due to a superior visualisation of anatomical networks and pathologic morphology compared to volumetric imaging alone. Furthermore, 3D-printed kidney models may facilitate interdisciplinary communication and decision-making regarding the management of patients undergoing operative treatment for renal disease. It cannot be suggested that a more expensive material constitutes a higher level of user-satisfaction and model accuracy. However, higher costs in the manufacturing of the 3D-printed models reported, on average, a slightly shorter time duration for the 3D-printing process and total manufacturing time.

scholarly journals Stress, strain and deformation of poly-lactic acid filament deposited onto polyethylene terephthalate woven fabric through 3D printing process

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Prisca Aude Eutionnat-Diffo ◽  
Yan Chen ◽  
Jinping Guan ◽  
Aurelie Cayla ◽  
Christine Campagne ◽  
...  
Keyword(s):  
Lactic Acid ◽  
3D Printing ◽  
Tensile Properties ◽  
Polyethylene Terephthalate ◽  
Polymeric Materials ◽  
Deposition Process ◽  
Woven Fabric ◽  
Poly Lactic Acid ◽  
Printing Process ◽  
3D Printed

Abstract Although direct deposition of polymeric materials onto textiles through 3D printing is a great technique used more and more to develop smart textiles, one of the main challenges is to demonstrate equal or better mechanical resistance, durability and comfort than those of the textile substrates before deposition process. This article focuses on studying the impact of the textile properties and printing platform temperature on the tensile and deformations of non-conductive and conductive poly lactic acid (PLA) filaments deposited onto polyethylene terephthalate (PET) textiles through 3D printing process and optimizing them using theoretical and statistical models. The results demonstrate that the deposition process affects the tensile properties of the printed textile in comparison with the ones of the textiles. The stress and strain at rupture of the first 3D printed PLA layer deposited onto PET textile material reveal to be a combination of those of the printed layer and the PET fabric due to the lower flexibility and diffusion of the polymeric printed track through the textile fabric leading to a weak adhesion at the polymer/textile interface. Besides, printing platform temperature and textile properties influence the tensile and deformation properties of the 3D printed PLA on PET textile significantly. Both, the washing process and the incorporation of conductive fillers into the PLA do not affect the tensile properties of the extruded polymeric materials. The elastic, total and permanent deformations of the 3D-printed PLA on PET fabrics are lower than the ones of the fabric before polymer deposition which demonstrates a better dimensional stability, higher stiffness and lower flexibility of these materials.

Sign in / Sign up

Export Citation Format

Share Document