Assessment of Multi-Scale SMOS and SMAP Soil Moisture Products across the Iberian Peninsula

In the last decade, technological advances led to the launch of two satellite missions dedicated to measure the Earth’s surface soil moisture (SSM): the ESA’s Soil Moisture and Ocean Salinity (SMOS) launched in 2009, and the NASA’s Soil Moisture Active Passive (SMAP) launched in 2015. The two satellites have an L-band microwave radiometer on-board to measure the Earth’s surface emission. These measurements (brightness temperatures TB) are then used to generate global maps of SSM every three days with a spatial resolution of about 30–40 km and a target accuracy of 0.04 m3/m3. To meet local applications needs, different approaches have been proposed to spatially disaggregate SMOS and SMAP TB or their SSM products. They rely on synergies between multi-sensor observations and are built upon different physical assumptions. In this study, temporal and spatial characteristics of six operational SSM products derived from SMOS and SMAP are assessed in order to diagnose their distinct features, and the rationale behind them. The study is focused on the Iberian Peninsula and covers the period from April 2015 to December 2017. A temporal inter-comparison analysis is carried out using in situ SSM data from the Soil Moisture Measurements Station Network of the University of Salamanca (REMEDHUS) to evaluate the impact of the spatial scale of the different products (1, 3, 9, 25, and 36 km), and their correspondence in terms of temporal dynamics. A spatial analysis is conducted for the whole Iberian Peninsula with emphasis on the added-value that the enhanced resolution products provide based on the microwave-optical (SMOS/ERA5/MODIS) or the active–passive microwave (SMAP/Sentinel-1) sensor fusion. Our results show overall agreement among time series of the products regardless their spatial scale when compared to in situ measurements. Still, higher spatial resolutions would be needed to capture local features such as small irrigated areas that are not dominant at the 1-km pixel scale. The degree to which spatial features are resolved by the enhanced resolution products depend on the multi-sensor synergies employed (at TB or soil moisture level), and on the nature of the fine-scale information used. The largest disparities between these products occur in forested areas, which may be related to the reduced sensitivity of high-resolution active microwave and optical data to soil properties under dense vegetation.

Download Full-text

Soil Moisture Retrievals by Combining Passive Microwave and Optical Data

Remote Sensing ◽

10.3390/rs12193173 ◽

2020 ◽

Vol 12 (19) ◽

pp. 3173

Author(s):

Cheng Tong ◽

Hongquan Wang ◽

Ramata Magagi ◽

Kalifa Goïta ◽

Luyao Zhu ◽

...

Keyword(s):

Soil Moisture ◽

Local Time ◽

Temporal Dynamics ◽

Ordinary Least Squares ◽

Optical Data ◽

Support Vector ◽

Learning Approaches ◽

Station Data ◽

Level 2

This paper aims to retrieve the temporal dynamics of soil moisture from 2015 to 2019 over an agricultural site in Southeast Australia using the Soil Moisture Active Passive (SMAP) brightness temperature. To meet this objective, two machine learning approaches, Random Forest (RF), Support Vector Machine (SVM), as well as a statistical Ordinary Least Squares (OLS) model were established, with the auxiliary data including the 16-day composite MODIS NDVI (MOD13Q1) and Surface Temperature (ST). The entire data were divided into two parts corresponding to ascending (6:00 p.m. local time) and descending (6:00 a.m. local time) orbits of SMAP overpasses. Thus, the three models were trained using the descending data acquired during the five years (2015 to 2019), and validated using the ascending product of the same period. Consequently, three different temporal variations of the soil moisture were obtained based on the three models. To evaluate their accuracies, the retrieved soil moisture was compared against the SMAP level-2 soil moisture product, as well as to in-situ ground station data. The comparative results show that the soil moisture obtained using the OLS, RF and SVM algorithms are highly correlated to the SMAP level-2 product, with high coefficients of determination (R2OLS = 0.981, R2SVM = 0.943, R2RF = 0.983) and low RMSE (RMSEOLS = 0.016 cm3/cm3, RMSESVM = 0.047 cm3/cm3, RMSERF = 0.016 cm3/cm3). Meanwhile, the estimated soil moistures agree with in-situ station data across different years (R2OLS = 0.376~0.85, R2SVM = 0.376~0.814, R2RF = 0.39~0.854; RMSEOLS = 0.049~0.105 cm3/cm3, RMSESVM = 0.073~0.1 cm3/cm3, RMSERF = 0.047~0.102 cm3/cm3), but an overestimation issue is observed for high vegetation conditions. The RF algorithm outperformed the SVM and OLS, in terms of the agreement with the ground measurements. This study suggests an alternative soil moisture retrieval scheme, in complementary to the SMAP baseline algorithm, for a fast soil moisture retrieval.

Download Full-text

Evaluating and Optimizing Surface Soil Moisture Drydowns in the ORCHIDEE Land Surface Model at In Situ Locations

Journal of Hydrometeorology ◽

10.1175/jhm-d-20-0115.1 ◽

2021 ◽

Vol 22 (4) ◽

pp. 1025-1043

Author(s):

Nina Raoult ◽

Catherine Ottlé ◽

Philippe Peylin ◽

Vladislav Bastrikov ◽

Pascal Maugis

Keyword(s):

Soil Moisture ◽

Land Surface ◽

Surface Soil ◽

Temporal Dynamics ◽

Gross Primary Production ◽

Bayesian Optimization ◽

Surface Model ◽

Surface Soil Moisture ◽

The Impact

AbstractThe rate at which land surface soils dry following rain events is an important feature of terrestrial models. It determines, for example, the water availability for vegetation, the occurrences of droughts, and the surface heat exchanges. As such, surface soil moisture (SSM) “drydowns,” i.e., the SSM temporal dynamics following a significant rainfall event, are of particular interest when evaluating and calibrating land surface models (LSMs). By investigating drydowns, characterized by an exponential decay time scale τ, we aim to improve the representation of SSM in the ORCHIDEE global LSM. We consider τ calculated over 18 International Soil Moisture Network sites found within the footprint of FLUXNET towers, covering different vegetation types and climates. Using the ORCHIDEE LSM, we compare τ from the modeled SSM time series to values computed from in situ SSM measurements. We then assess the potential of using τ observations to constrain some water, carbon, and energy parameters of ORCHIDEE, selected using a sensitivity analysis, through a standard Bayesian optimization procedure. The impact of the SSM optimization is evaluated using FLUXNET evapotranspiration and gross primary production (GPP) data. We find that the relative drydowns of SSM can be well calibrated using observation-based τ estimates, when there is no need to match the absolute observed and modeled SSM values. When evaluated using independent data, τ-calibration parameters were able to improve drydowns for 73% of the sites. Furthermore, the fit of the model to independent fluxes was only minutely changed. We conclude by considering the potential of global satellite products to scale up the experiment to a global-scale optimization.

Download Full-text

Global soil moisture data derived through machine learning trained with in-situ measurements

Scientific Data ◽

10.1038/s41597-021-00964-1 ◽

2021 ◽

Vol 8 (1) ◽

Author(s):

Sungmin O. ◽

Rene Orth

Keyword(s):

Machine Learning ◽

Soil Moisture ◽

Large Scale ◽

Short Term Memory ◽

Temporal Dynamics ◽

Soil Moisture Data ◽

Wide Range ◽

Global Soil

AbstractWhile soil moisture information is essential for a wide range of hydrologic and climate applications, spatially-continuous soil moisture data is only available from satellite observations or model simulations. Here we present a global, long-term dataset of soil moisture derived through machine learning trained with in-situ measurements, SoMo.ml. We train a Long Short-Term Memory (LSTM) model to extrapolate daily soil moisture dynamics in space and in time, based on in-situ data collected from more than 1,000 stations across the globe. SoMo.ml provides multi-layer soil moisture data (0–10 cm, 10–30 cm, and 30–50 cm) at 0.25° spatial and daily temporal resolution over the period 2000–2019. The performance of the resulting dataset is evaluated through cross validation and inter-comparison with existing soil moisture datasets. SoMo.ml performs especially well in terms of temporal dynamics, making it particularly useful for applications requiring time-varying soil moisture, such as anomaly detection and memory analyses. SoMo.ml complements the existing suite of modelled and satellite-based datasets given its distinct derivation, to support large-scale hydrological, meteorological, and ecological analyses.

Download Full-text

SMOS Neural Network Soil Moisture Data Assimilation in a Land Surface Model and Atmospheric Impact

10.20944/preprints201904.0216.v1 ◽

2019 ◽

Author(s):

Nemesio Rodriguez-Fernandez ◽

Patricia de Rosnay ◽

Clement Albergel ◽

Philippe Richaume ◽

Filipe Aires ◽

...

Keyword(s):

Neural Network ◽

Soil Moisture ◽

Data Assimilation ◽

Land Surface ◽

Positive Impact ◽

Land Surface Model ◽

Surface Model ◽

Northern Asia ◽

The Impact

The assimilation of Soil Moisture and Ocean Salinity (SMOS) data into the ECMWF (European Centre for Medium Range Weather Forecasts) H-TESSEL (Hydrology revised - Tiled ECMWF Scheme for Surface Exchanges over Land) model is presented. SMOS soil moisture (SM) estimates have been produced specifically by training a neural network with SMOS brightness temperatures as input and H-TESSEL model SM simulations as reference. This can help the assimilation of SMOS information in several ways: (1) the neural network soil moisture (NNSM) data have a similar climatology to the model, (2) no global bias is present with respect to the model even if regional differences can exist. Experiments performing joint data assimilation (DA) of NNSM, 2 metre air temperature and relative humidity or NNSM-only DA are discussed. The resulting SM was evaluated against a large number of in situ measurements of SM obtaining similar results to those of the model with no assimilation, even if significant differences were found from site to site. In addition, atmospheric forecasts initialized with H-TESSEL runs (without DA) or with the analysed SM were compared to measure of the impact of the satellite information. Although, NNSM DA has an overall neutral impact in the forecast in the Tropics, a significant positive impact was found in other areas and periods, especially in regions with limited in situ information. The joint NNSM, T2m and RH2m DA improves the forecast for all the seasons in the Southern Hemisphere. The impact is mostly due to T2m and RH2m, but SMOS NN DA alone also improves the forecast in July- September. In the Northern Hemisphere, the joint NNSM, T2m and RH2m DA improves the forecast in April-September, while NNSM alone has a significant positive effect in July-September. Furthermore, forecasting skill maps show that SMOS NNSM improves the forecast in North America and in Northern Asia for up to 72 hours lead time.

Download Full-text

Physical factors of influence in the interactions between rainfall, evapotranspiration and soil moisture driving the spatio-temporal evolution of drought patterns in the Ebro Basin (NE Spain).

10.5194/egusphere-egu21-2377 ◽

2021 ◽

Author(s):

Jaime Gaona ◽

Pere Quintana-Seguí ◽

Maria José Escorihuela

Keyword(s):

Soil Moisture ◽

Land Cover ◽

Iberian Peninsula ◽

Land Surface ◽

Temporal Analysis ◽

Drought Indices ◽

Surface Model ◽

Physical Factors ◽

Spatio Temporal ◽

The Impact

Droughts in the Iberian Peninsula are a natural hazard of great relevance due to their recurrence, severity and impact on multiple environmental and socioeconomic aspects. The Ebro Basin, located in the NE of the Iberian Peninsula, is particularly vulnerable to drought with consequences on agriculture, urban water supply and hydropower. This study, performed within the Project HUMID (CGL2017-85687-R), aims at evaluating the influence of the climatic, land cover and soil characteristics on the interactions between rainfall, evapotranspiration and soil moisture anomalies which define the spatio-temporal drought patterns in the basin.The onset, propagation and mitigation of droughts in the Iberian Peninsula is driven by anomalies of rainfall, evapotranspiration and soil moisture, which are related by feedback processes. To test the relative importance of such anomalies, we evaluate the contribution of climatic, land-cover and geologic heterogeneity on the definition of the spatio-temporal patterns of drought. We use the K&#246;ppen-Geiger climatic classification to assess how the contrasting climatic types within the basin determine differences on drought behavior. Land-cover types that govern the partition between evaporation and transpiration are also of great interest to discern the influence of vegetation and crop types on the anomalies of evapotranspiration across the distinct regions of the basin (e.g. forested mountains vs. crop-dominated areas). The third physical characteristic whose effect on drought we investigate is the impact of soil properties on soil moisture anomalies.The maps and time series used for the spatio-temporal analysis are based on drought indices calculated with high-resolution datasets from remote sensing (MOD16A2ET and SMOS1km) and the land-surface model SURFEX-ISBA. The Standardized Precipitation Index (SPI), the EvapoTranspiration Deficit Index (ETDI) and the Soil Moisture Deficit Index (SMDI) are the three indices chosen to characterize the anomalies of the corresponding rainfall (atmospheric), evapotranspiration (atmosphere-land interface) and soil moisture (land) anomalies (components of the water balance). The comparison of the correlations of the indices (with different time lags) between contrasting regions offers insights about the impact of climate, land-cover and soil properties in the dominance, the timing of the response and memory aspects of the interactions. The high spatial and temporal resolution of remote sensing and land-surface model data allows adopting time and spatial scales suitable to investigate the influence of these physical factors with detail beyond comparison with ground-based datasets.The spatial and temporal analysis prove useful to investigate the physical factors of influence on the anomalies between rainfall, evapotranspiration and soil moisture. This approach facilitates the physical interpretation of the anomalies of drought indices aiming to improve the characterization of drought in heterogeneous semi-arid areas like the Ebro River Basin.

Download Full-text

Copernicus Imaging Microwave Radiometer (CIMR) Benefits for the Copernicus Level 4 Sea-Surface Salinity Processing Chain

Remote Sensing ◽

10.3390/rs11151818 ◽

2019 ◽

Vol 11 (15) ◽

pp. 1818 ◽

Cited By ~ 2

Author(s):

Daniele Ciani ◽

Rosalia Santoleri ◽

Gian Luigi Liberti ◽

Catherine Prigent ◽

Craig Donlon ◽

...

Keyword(s):

Soil Moisture ◽

High Resolution ◽

Microwave Radiometer ◽

Ocean Surface ◽

Sea Surface ◽

Sea Surface Salinity ◽

Optimal Interpolation ◽

Surface Salinity ◽

Processing Chain

We present a study on the potential of the Copernicus Imaging Microwave Radiometer (CIMR) mission for the global monitoring of Sea-Surface Salinity (SSS) using Level-4 (gap-free) analysis processing. Space-based SSS are currently provided by the Soil Moisture and Ocean Salinity (SMOS) and Soil Moisture Active Passive (SMAP) satellites. However, there are no planned missions to guarantee continuity in the remote SSS measurements for the near future. The CIMR mission is in a preparatory phase with an expected launch in 2026. CIMR is focused on the provision of global coverage, high resolution sea-surface temperature (SST), SSS and sea-ice concentration observations. In this paper, we evaluate the mission impact within the Copernicus Marine Environment Monitoring Service (CMEMS) SSS processing chain. The CMEMS SSS operational products are based on a combination of in situ and satellite (SMOS) SSS and high-resolution SST information through a multivariate optimal interpolation. We demonstrate the potential of CIMR within the CMEMS SSS operational production after the SMOS era. For this purpose, we implemented an Observing System Simulation Experiment (OSSE) based on the CMEMS MERCATOR global operational model. The MERCATOR SSSs were used to generate synthetic in situ and CIMR SSS and, at the same time, they provided a reference gap-free SSS field. Using the optimal interpolation algorithm, we demonstrated that the combined use of in situ and CIMR observations improves the global SSS retrieval compared to a processing where only in situ observations are ingested. The improvements are observed in the 60% and 70% of the global ocean surface for the reconstruction of the SSS and of the SSS spatial gradients, respectively. Moreover, the study highlights the CIMR-based salinity patterns are more accurate both in the open ocean and in coastal areas. We conclude that CIMR can guarantee continuity for accurate monitoring of the ocean surface salinity from space.

Download Full-text

The impact of near-surface soil moisture assimilation at subseasonal, seasonal, and inter-annual timescales

Hydrology and Earth System Sciences ◽

10.5194/hess-19-4831-2015 ◽

2015 ◽

Vol 19 (12) ◽

pp. 4831-4844 ◽

Cited By ~ 19

Author(s):

C. Draper ◽

R. Reichle

Keyword(s):

Soil Moisture ◽

Data Assimilation ◽

Surface Soil ◽

Root Zone ◽

Surface Model ◽

Surface Soil Moisture ◽

Near Surface ◽

In Situ Observations ◽

The Impact

Abstract. A 9 year record of Advanced Microwave Scanning Radiometer – Earth Observing System (AMSR-E) soil moisture retrievals are assimilated into the Catchment land surface model at four locations in the US. The assimilation is evaluated using the unbiased mean square error (ubMSE) relative to watershed-scale in situ observations, with the ubMSE separated into contributions from the subseasonal (SMshort), mean seasonal (SMseas), and inter-annual (SMlong) soil moisture dynamics. For near-surface soil moisture, the average ubMSE for Catchment without assimilation was (1.8 × 10−3 m3 m−3)2, of which 19 % was in SMlong, 26 % in SMseas, and 55 % in SMshort. The AMSR-E assimilation significantly reduced the total ubMSE at every site, with an average reduction of 33 %. Of this ubMSE reduction, 37 % occurred in SMlong, 24 % in SMseas, and 38 % in SMshort. For root-zone soil moisture, in situ observations were available at one site only, and the near-surface and root-zone results were very similar at this site. These results suggest that, in addition to the well-reported improvements in SMshort, assimilating a sufficiently long soil moisture data record can also improve the model representation of important long-term events, such as droughts. The improved agreement between the modeled and in situ SMseas is harder to interpret, given that mean seasonal cycle errors are systematic, and systematic errors are not typically targeted by (bias-blind) data assimilation. Finally, the use of 1-year subsets of the AMSR-E and Catchment soil moisture for estimating the observation-bias correction (rescaling) parameters is investigated. It is concluded that when only 1 year of data are available, the associated uncertainty in the rescaling parameters should not greatly reduce the average benefit gained from data assimilation, although locally and in extreme years there is a risk of increased errors.

Download Full-text

A bare ground evaporation revision in the ECMWF land-surface scheme: evaluation of its impact using ground soil moisture and satellite microwave data

Hydrology and Earth System Sciences ◽

10.5194/hess-16-3607-2012 ◽

2012 ◽

Vol 16 (10) ◽

pp. 3607-3620 ◽

Cited By ~ 30

Author(s):

C. Albergel ◽

G. Balsamo ◽

P. de Rosnay ◽

J. Muñoz-Sabater ◽

S. Boussetta

Keyword(s):

Soil Moisture ◽

Brightness Temperature ◽

Land Surface ◽

The United States ◽

Microwave Emission ◽

Bare Ground ◽

New Formulation ◽

The Impact ◽

Surface Fields

Abstract. In situ soil moisture data from 122 stations across the United States are used to evaluate the impact of a new bare ground evaporation formulation at ECMWF. In November 2010, the bare ground evaporation used in ECMWF's operational Integrated Forecasting System (IFS) was enhanced by adopting a lower stress threshold than for the vegetation, allowing a higher evaporation. It results in more realistic soil moisture values when compared to in situ data, particularly over dry areas. Use was made of the operational IFS and offline experiments for the evaluation. The latter are based on a fixed version of the IFS and make it possible to assess the impact of a single modification, while the operational analysis is based on a continuous effort to improve the analysis and modelling systems, resulting in frequent updates (a few times a year). Considering the field sites with a fraction of bare ground greater than 0.2, the root mean square difference (RMSD) of soil moisture is shown to decrease from 0.118 m3 m−3 to 0.087 m3 m−3 when using the new formulation in offline experiments, and from 0.110 m3 m−3 to 0.088 m3 m−3 in operations. It also improves correlations. Additionally, the impact of the new formulation on the terrestrial microwave emission at a global scale is investigated. Realistic and dynamically consistent fields of brightness temperature as a function of the land surface conditions are required for the assimilation of the SMOS data. Brightness temperature simulated from surface fields from two offline experiments with the Community Microwave Emission Modelling (CMEM) platform present monthly mean differences up to 7 K. Offline experiments with the new formulation present drier soil moisture, hence simulated brightness temperature with its surface fields are larger. They are also closer to SMOS remotely sensed brightness temperature.

Download Full-text

Defining a Trade-off Between Spatial and Temporal Resolution of a Geosynchronous SAR Mission for Soil Moisture Monitoring

Remote Sensing ◽

10.3390/rs10121950 ◽

2018 ◽

Vol 10 (12) ◽

pp. 1950 ◽

Cited By ~ 3

Author(s):

Luca Cenci ◽

Luca Pulvirenti ◽

Giorgio Boni ◽

Nazzareno Pierdicca

Keyword(s):

Soil Moisture ◽

Spatial Resolution ◽

Temporal Resolution ◽

Added Value ◽

Sar Images ◽

Radar Images ◽

Spatio Temporal ◽

Set Up ◽

The Impact ◽

Hydrological Applications

The next generation of synthetic aperture radar (SAR) systems could foresee satellite missions based on a geosynchronous orbit (GEO SAR). These systems are able to provide radar images with an unprecedented combination of spatial (≤1 km) and temporal (≤12 h) resolutions. This paper investigates the GEO SAR potentialities for soil moisture (SM) mapping finalized to hydrological applications, and defines the best compromise, in terms of image spatio-temporal resolution, for SM monitoring. A synthetic soil moisture–data assimilation (SM-DA) experiment was thus set up to evaluate the impact of the hydrological assimilation of different GEO SAR-like SM products, characterized by diverse spatio-temporal resolutions. The experiment was also designed to understand if GEO SAR-like SM maps could provide an added value with respect to SM products retrieved from SAR images acquired from satellites flying on a quasi-polar orbit, like Sentinel-1 (POLAR SAR). Findings showed that GEO SAR systems provide a valuable contribution for hydrological applications, especially if the possibility to generate many sub-daily observations is sacrificed in favor of higher spatial resolution. In the experiment, it was found that the assimilation of two GEO SAR-like observations a day, with a spatial resolution of 100 m, maximized the performances of the hydrological predictions, for both streamflow and SM state forecasts. Such improvements of the model performances were found to be 45% higher than the ones obtained by assimilating POLAR SAR-like SM maps.

Download Full-text

Comparing Assimilation of Soil Moisture and C-band Backscatter in High Resolution Land Surface Model

10.5194/egusphere-egu2020-10277 ◽

2020 ◽

Author(s):

Leqiang Sun ◽

Stéphane Belair ◽

Marco Carrera ◽

Bernard Bilodeau

Keyword(s):

Soil Moisture ◽

Land Surface ◽

Land Surface Model ◽

Open Loop ◽

In Situ Measurements ◽

Lookup Table ◽

Surface Model ◽

Loop Model ◽

The Impact

Canadian Space Agency (CSA) has recently started receiving and processing the images from the recently launched C-band RADARSAT Constellation Mission (RCM). The backscatter and soil moisture retrievals products from the previously launched RADARSAT-2 agree well with both in-situ measurements and surface soil moisture modeled with land surface model Soil, Vegetation, and Snow (SVS). RCM will provide those products at an even better spatial coverage and temporal resolution. In preparation of the potential operational application of RCM products in Canadian Meteorological Center (CMC), this paper presents the scenarios of assimilating either soil moisture retrieval or outright backscatter signal in a 100-meter resolution version of the Canadian Land Data Assimilation System (CaLDAS) on field scale with time interval of three hours. The soil moisture retrieval map was synthesized by extrapolating the regression relationship between in-situ measurements and open loop model output based on soil texture lookup table. Based on this, the backscatter map was then generated with the surface roughness retrieved from RADARSAT-2 images using a modified Integral Equation Model (IEM) model. Bias correction was applied to the Ensemble Kalman filter (EnKF) to mitigate the impact of nonlinear errors introduced by multi-sourced perturbations. Initial results show that the assimilation of backscatter is as effective as assimilating soil moisture retrievals. Compared to open loop, both can improve the analysis of surface moisture, particularly in terms of reducing bias. &#160;

Download Full-text