scholarly journals Radiative Transfer Model Simulations for Ground-Based Microwave Radiometers in North China

2021 ◽  
Vol 13 (24) ◽  
pp. 5161
Author(s):  
Wenying He ◽  
Yunchu Cheng ◽  
Rongshi Zou ◽  
Pucai Wang ◽  
Hongbin Chen ◽  
...  
Keyword(s):  
Water Vapor ◽  
Radiative Transfer ◽  
North China ◽  
Radiative Transfer Model ◽  
Oxygen Absorption ◽  
Transfer Model ◽  
Profile Data ◽  
Radiosonde Station ◽  
Atmospheric Profiles

Ground-based microwave radiometer profilers (MWRPs) are widely used to provide high-temporal resolution atmospheric temperature and humidity profiles. The quality of the observed brightness temperature (TB) from MWRPs is key for retrieving accurate atmospheric profiles. In this study, TB simulations derived from a radiative transfer model (RTM) were used to assess the quality of TB observations. Two types of atmospheric profile data (conventional radiosonde and ERA5 reanalysis) were combined with the RTM to obtain TB simulations, then compared with corresponding observations from three MWRPs located in different places in North China to investigate the influence of input atmospheric profiles on TB simulations and evaluate the quality of TB observations from the three MWRPs. The comparisons of the matching samples under clear-sky conditions showed that TB simulations derived from both radiosonde and ERA5 profiles were very close to the TB observations from most of the MWRP channels; however, the correlation was lower and the bias was obvious at 51.26 GHz and 52.28 GHz, which indicates that the oxygen absorption component in the RTM needs to be improved for lower-frequency temperature channels. The difference in location of the radiosonde and MWRP sites affected the TB simulations for the water vapor channels, but had little impact on temperature channels that are insensitive to humidity. Comparisons of both simulations (ERA5 and Radiosonde) and the corresponding TB observations from the three sites indicated that the water vapor channels observation quality for the MWRP located in southern Beijing needs improvement. For the two types of profile data, ERA5 profiles have a more positive effect on TB simulations in the water vapor channels, such as enhanced consistence, reduced bias and standard deviation between simulations and observations for those MWRPs located away from the radiosonde station. Therefore, hourly ERA5 data are an optimal option in terms of compensating for limited radiosonde measurements and enhancing the monitoring quality of MWRP observations within 24 h.

scholarly journals Performance of the line-by-line radiative transfer model (LBLRTM) for temperature and species retrievals: IASI case studies from JAIVEx

2009 ◽  
Vol 9 (19) ◽  
pp. 7397-7417 ◽  
Author(s):  
M. W. Shephard ◽  
S. A. Clough ◽  
V. H. Payne ◽  
W. L. Smith ◽  
S. Kireev ◽  
...  
Keyword(s):  
Water Vapor ◽  
Radiative Transfer ◽  
Trace Gas ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Line Intensities ◽  
Remote Sounding ◽  
Instrument Noise ◽  
Large Peak ◽  
Line Coupling

Abstract. Presented here are comparisons between the Infrared Atmospheric Sounding instrument (IASI) and the "Line-By-Line Radiative Transfer Model" (LBLRTM). Spectral residuals from radiance closure studies during the IASI JAIVEx validation campaign provide insight into a number of spectroscopy issues relevant to remote sounding of temperature, water vapor and trace gases from IASI. In order to perform quality IASI trace gas retrievals, the temperature and water vapor fields must be retrieved as accurately as possible. In general, the residuals in the CO2 ν2 region are of the order of the IASI instrument noise. However, outstanding issues with the CO2 spectral regions remain. There is a large residual ~−1.7 K in the 667 cm−1 Q-branch, and residuals in the CO2 ν2 and N2O/CO2 ν3 spectral regions that sample the troposphere are inconsistent, with the N2O/CO2 ν3 region being too negative (warmer) by ~0.7 K. Residuals on this lower wavenumber side of the CO2 ν3 band will be improved by line parameter updates, while future efforts to reduce the residuals reaching ~−0.5 K on the higher wavenumber side of the CO2 ν3 band will focus on addressing limitations in the modeling of the CO2 line shape (line coupling and duration of collision) effects. Brightness temperature residuals from the radiance closure studies in the ν2 water vapor band have standard deviations of ~0.2–0.3 K with some large peak residuals reaching ±0.5–1.0 K. These are larger than the instrument noise indicating that systematic errors still remain. New H2O line intensities and positions have a significant impact on the retrieved water vapor, particularly in the upper troposphere where the water vapor retrievals are 10% drier when using line intensities compared with HITRAN 2004. In addition to O3, CH4, and CO, of the IASI instrument combined with an accurate forward model allows for the detection of minor species with weak atmospheric signatures in the nadir radiances, such as HNO3 and OCS.

Greenhouse effects of aircraft emissions as calculated by a radiative transfer model

1995 ◽  
Vol 13 (4) ◽  
pp. 413-418 ◽  
Author(s):  
J. P. F. Fortuin ◽  
R. van Dorland ◽  
W. M. F. Wauben ◽  
H. Kelder
Keyword(s):  
Water Vapor ◽  
Radiative Transfer ◽  
Indirect Effect ◽  
Radiative Forcing ◽  
Combustion Products ◽  
Ozone Production ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Aircraft Emissions ◽  
The North

Abstract. With a radiative transfer model, assessments are made of the radiative forcing in northern mid-latitudes due to aircraft emissions up to 1990. Considered are the direct climate effects from the major combustion products carbon dioxide, nitrogen dioxide, water vapor and sulphur dioxide, as well as the indirect effect of ozone production from NOx emissions. Our study indicates a local radiative forcing at the tropopause which should be negative in summer (–0.5 to 0.0 W/m2) and either negative or positive in winter (–0.3 to 0.2 W/m2). To these values the indirect effect of contrails has to be added, which for the North Atlantic Flight Corridor covers the range –0.2 to 0.3 W/m2 in summer and 0.0 to 0.3 W/m2 in winter. Apart from optically dense non-aged contrails during summer, negative forcings are due to solar screening by sulphate aerosols. The major positive contributions come from contrails, stratospheric water vapor in winter and ozone in summer. The direct effect of NO2 is negligible and the contribution of CO2 is relatively small.

scholarly journals Performance of the Line-By-Line Radiative Transfer Model (LBLRTM) for temperature, water vapor, and trace gas retrievals: recent updates evaluated with IASI case studies

2013 ◽  
Vol 13 (14) ◽  
pp. 6687-6711 ◽  
Author(s):  
M. J. Alvarado ◽  
V. H. Payne ◽  
E. J. Mlawer ◽  
G. Uymin ◽  
M. W. Shephard ◽  
...  
Keyword(s):  
Water Vapor ◽  
Radiative Transfer ◽  
Fixed Ratio ◽  
Satellite Observations ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Temperature Profiles ◽  
A Posteriori ◽  
The Impact ◽  
Temperature Water

Abstract. Modern data assimilation algorithms depend on accurate infrared spectroscopy in order to make use of the information related to temperature, water vapor (H2O), and other trace gases provided by satellite observations. Reducing the uncertainties in our knowledge of spectroscopic line parameters and continuum absorption is thus important to improve the application of satellite data to weather forecasting. Here we present the results of a rigorous validation of spectroscopic updates to an advanced radiative transfer model, the Line-By-Line Radiative Transfer Model (LBLRTM), against a global dataset of 120 near-nadir, over-ocean, nighttime spectra from the Infrared Atmospheric Sounding Interferometer (IASI). We compare calculations from the latest version of LBLRTM (v12.1) to those from a previous version (v9.4+) to determine the impact of spectroscopic updates to the model on spectral residuals as well as retrieved temperature and H2O profiles. We show that the spectroscopy in the CO2 ν2 and ν3 bands is significantly improved in LBLRTM v12.1 relative to v9.4+, and that these spectroscopic updates lead to mean changes of ~0.5 K in the retrieved vertical temperature profiles between the surface and 10 hPa, with the sign of the change and the variability among cases depending on altitude. We also find that temperature retrievals using each of these two CO2 bands are remarkably consistent in LBLRTM v12.1, potentially allowing these bands to be used to retrieve atmospheric temperature simultaneously. The updated H2O spectroscopy in LBLRTM v12.1 substantially improves the a posteriori residuals in the P-branch of the H2O ν2 band, while the improvements in the R-branch are more modest. The H2O amounts retrieved with LBLRTM v12.1 are on average 14% lower between 100 and 200 hPa, 42% higher near 562 hPa, and 31% higher near the surface compared to the amounts retrieved with v9.4+ due to a combination of the different retrieved temperature profiles and the updated H2O spectroscopy. We also find that the use of a fixed ratio of HDO to H2O in LBLRTM may be responsible for a significant fraction of the remaining bias in the P-branch relative to the R-branch of the H2O ν2 band. There were no changes to O3 spectroscopy between the two model versions, and so both versions give positive a posteriori residuals of ~ 0.3 K in the R-branch of the O3 ν3 band. While the updates to the H2O self-continuum employed by LBLRTM v12.1 have clearly improved the match with observations near the CO2 ν3 band head, we find that these updates have significantly degraded the match with observations in the fundamental band of CO. Finally, significant systematic a posteriori residuals remain in the ν4 band of CH4, but the magnitude of the positive bias in the retrieved mixing ratios is reduced in LBLRTM v12.1, suggesting that the updated spectroscopy could improve retrievals of CH4 from satellite observations.

scholarly journals An assessment of the accuracy of the RTTOV fast radiative transfer model using IASI data

2009 ◽  
Vol 9 (2) ◽  
pp. 9491-9535 ◽  
Author(s):  
M. Matricardi
Keyword(s):  
Radiative Transfer ◽  
Regression Coefficients ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Weather Forecasts ◽  
Medium Range ◽  
Forecasting System ◽  
Relative Differences ◽  
Temperature Water

Abstract. IASI measurements of spectral radiances made between the 1 April 2008 and the 15 April 2008 are compared with simulations performed using the RTTOV fast radiative transfer model utilizing regression coefficients based on different line-by-line models. The comparisons are performed within the framework of the European Centre for Medium-Range Weather Forecasts Integrated Forecasting System using fields of temperature, water vapour and ozone obtained from short-range forecasts. Simulations are performed to assess the accuracy of the RTTOV computations and investigate relative differences between the line-by-line models and the quality of the spectroscopic databases on which the RTTOV coefficients are based.

scholarly journals Improving Satellite-Derived Sea Surface Temperature Accuracies Using Water Vapor Profile Data

2011 ◽  
Vol 28 (1) ◽  
pp. 85-93 ◽  
Author(s):  
Ian J. Barton
Keyword(s):  
Water Vapor ◽  
Radiative Transfer ◽  
Surface Temperature ◽  
Sea Surface Temperature ◽  
Satellite Data ◽  
Sea Surface ◽  
Radiative Transfer Model ◽  
Clear Correlation ◽  
Transfer Model ◽  
The Difference

Abstract Analyses based on atmospheric infrared radiative transfer simulations and collocated ship and satellite data are used to investigate whether knowledge of vertical atmospheric water vapor distributions can improve the accuracy of sea surface temperature (SST) estimates from satellite data. Initially, a simulated set of satellite brightness temperatures generated by a radiative transfer model with a large maritime radiosonde database was obtained. Simple linear SST algorithms are derived from this dataset, and these are then reapplied to the data to give simulated SST estimates and errors. The concept of water vapor weights is introduced in which a weight is a measure of the layer contribution to the difference between the surface temperature and that measured by the satellite. The weight of each atmospheric layer is defined as the layer water vapor amount multiplied by the difference between the SST and the midlayer temperature. Satellite-derived SST errors are then plotted against the difference in the sum of weights above an altitude of 2.5 km and that below. For the simple two-channel (with typical wavelengths of 11 and 12 μm) analysis, a clear correlation between the weights differences and the SST errors is found. A second group of analyses using ship-released radiosondes and satellite data also show a correlation between the SST errors and the weights differences. The analyses suggest that, for an SST derived using a simple two-channel algorithm, the accuracy may be improved if account is taken of the vertical distribution of water vapor above the ocean surface. For SST estimates derived using algorithms that include data from a 3.7-μm channel, there is no such correlation found.

scholarly journals On water vapor Jacobian in fast radiative transfer model

2010 ◽  
Vol 115 (D12) ◽  
Author(s):  
Yong Chen ◽  
Yong Han ◽  
Paul Van Delst ◽  
Fuzhong Weng
Keyword(s):  
Water Vapor ◽  
Radiative Transfer ◽  
Radiative Transfer Model ◽  
Transfer Model

Characterization of Bias of Advanced Himawari Imager Infrared Observations from NWP Background Simulations Using CRTM and RTTOV

2016 ◽  
Vol 33 (12) ◽  
pp. 2553-2567 ◽  
Author(s):  
X. Zou ◽  
X. Zhuge ◽  
F. Weng
Keyword(s):  
Water Vapor ◽  
Radiative Transfer ◽  
Land Surface ◽  
Near Infrared ◽  
Weather Prediction ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Brightness Temperatures ◽  
Emissivity Model ◽  
New Generation

AbstractStarting in 2014, the new generation of Japanese geostationary meteorological satellites carries an Advanced Himawari Imager (AHI) to provide the observations of visible, near infrared, and infrared with much improved spatial and temporal resolutions. For applications of the AHI measurements in numerical weather prediction (NWP) data assimilation systems, the biases of the AHI brightness temperatures at channels 7–16 from the model simulations are first characterized and evaluated using both the Community Radiative Transfer Model (CRTM) and the Radiative Transfer for the TIROS Operational Vertical Sounder (RTTOV). It is found that AHI biases under a clear-sky atmosphere are independent of satellite zenith angle except for channel 7. The biases of three water vapor channels increase with scene brightness temperatures and are nearly constant except at high brightness temperatures for the remaining infrared channels. The AHI biases at all the infrared channels are less than 0.6 and 1.2 K over ocean and land, respectively. The differences in biases between RTTOV and CRTM with the land surface emissivity model used in RTTOV are small except for the upper-tropospheric water vapor channels 8 and 9 and the low-tropospheric carbon dioxide channel 16. Since the inputs used for simulations are the same for CRTM and RTTOV, the differential biases at the water vapor channels may be associated with subtle differences in forward models.

Sign in / Sign up

Export Citation Format

Share Document