scholarly journals A Novel Non-Intrusive Vibration Energy Harvesting Method for Air Conditioning Compressor Unit

2021 ◽  
Vol 13 (18) ◽  
pp. 10300
Author(s):  
Chuan Choong Yang ◽  
Noor Fiqri Razqi Bin Noor Hanafi ◽  
Noor Hazrin Hany Bt Mohamad Hanif ◽  
Ahmad Faris Ismail ◽  
Hsueh-Hsien Chang
Keyword(s):  
Flow Rate ◽  
Air Conditioning ◽  
Volume Flow Rate ◽  
Piezoelectric Sensor ◽  
Volume Flow ◽  
Vibration Energy ◽  
Compressor Unit ◽  
Flow Rates ◽  
Air Volume ◽  
Custom Made

The purpose of harvesting vibration energy is to obtain clean and sustainable energy by converting vibration energy from ambient sources into a voltage output. In this work, a piezoelectric sensor, PZT-5H is attached to a 3D printed and custom-made mounting to be placed at an air conditioning condenser unit, to harvest vibration energy. The configuration of the harvester is non-intrusive, in which the harvester did not intrude into compressor unit operation. Temperature (20 °C, 22 °C, and 24 °C) and air volume flow rates (3 levels of air volume flow rate at 245 L/second, 274 L/second, and 297 L/second) were taken into consideration in this investigation. An accelerometer was first used to investigate the optimum vibration frequency in Hertz, and six locations were identified. Next, the piezoelectric sensor was mounted at these six locations, and the output root-mean-square (RMS) voltage from the piezoelectric sensor was obtained. The analysis of variance (ANOVA) indicated that temperature and air volume flow rates factors were significant. It was found that the location identified with the highest amount of vibration at 830.2 Hz from accelerometer measurement, was also the highest amount of RMS voltage, at 510.82 mV, harvested by the piezoelectric, from the temperature of 20 °C and air volume flow rates at high level (air flow volume flow rate at 297 L/second). From this work, it is feasible to utilize this novel method of harvesting waste vibration energy from the air conditioning compressor unit.

scholarly journals Coupling Effect of Air Flow Rate and Operating Conditions on the Performance of Electric Vehicle R744 Air Conditioning System

2021 ◽  
Vol 11 (11) ◽  
pp. 4855
Author(s):  
Anci Wang ◽  
Jianmin Fang ◽  
Xiang Yin ◽  
Yulong Song ◽  
Feng Cao ◽  
...  
Keyword(s):  
Electric Vehicle ◽  
Flow Rate ◽  
Air Conditioning ◽  
Volume Flow Rate ◽  
Air Flow ◽  
Volume Flow ◽  
Air Flow Rate ◽  
Air Volume ◽  
Discharge Pressure ◽  
Air Conditioning Systems

The air flow rate on the gas cooler side is one of the key parameters affecting the performance and running safety of transcritical CO2 electric vehicle air conditioning systems. After experimentally analyzing the effects of the air volume flow rate in the gas cooler on the cycle parameters and system performance, a novel method to evaluate the optimal air flow rate was proposed. In addition, the effect of the gas cooler air volume flow rate on the key performance parameters of the system (e.g., optimal discharge pressure) was explored. Finally, the coupling effects of the compressor speed, ambient temperature and optimal air flow rate on the system performance was also exhaustively assessed. It was found that as the discharge temperature, the CO2 temperature at the gas cooler outlet and the discharge pressure did not vary more than ±2%, the corresponding gas cooler air volume flow rate was optimal. For the single-row and dual-process microchannel evaporator used in this work, the recommended value of the optimal gas cooler air volume flow rate was 2500 m3·h−1. The results could provide reference for the fan speed design of electric vehicle CO2 air conditioning systems, especially for the performance under idling model.

Numerical Simulation on Air Volume Flow Rate Distribution of Stator Ducts for Salient Pole Synchronous Motor

2014 ◽  
Vol 644-650 ◽  
pp. 373-376
Author(s):  
Li Liu ◽  
Yi Ping Lu ◽  
Jia De Han ◽  
Xue Mei Sun
Keyword(s):  
Flow Rate ◽  
Volume Flow Rate ◽  
Domain Boundary ◽  
Air Flow ◽  
Flow Characteristics ◽  
Synchronous Motor ◽  
Volume Flow ◽  
Rate Distribution ◽  
Salient Pole ◽  
Air Volume

Air volume flow rate distribution of stator ducts along axial and circumferential for salient pole synchronous motor is strongly influenced by the air flow field in the air gap and rotor poles, which is completely different from the flow characteristics of non-salient pole motor and it directly relates to the peak temperature of stator bars and core and axial temperature difference which can affect the safety of the operation. A three-dimensional physical model of 1/8 motor was established and corresponding solution domain boundary conditions were given in this article. The air volume flow rate distribution of stator ducts along axial and circumferential was analyzed based on CFD. The study show that at the same position of the axial stator, the cooling air flow into stator ducts along the circumferential direction is uneven, the air volume flow rate distribution is largely influenced by rotor pole pieces, geometry and position of pole support block and rotor rotation direction.

scholarly journals Effects of Arterial Pco2 and Cerebrospinal Fluid Volume Flow Rate Changes on Choroid Plexus and Cerebral Blood Flow in Normal and Experimental Hydrocephalic Cats

1983 ◽  
Vol 3 (3) ◽  
pp. 369-375 ◽  
Author(s):  
S. Nakamura ◽  
G. M. Hochwald
Keyword(s):  
Blood Flow ◽  
Cerebrospinal Fluid ◽  
Cerebral Cortex ◽  
Choroid Plexus ◽  
Flow Rate ◽  
Volume Flow Rate ◽  
Volume Flow ◽  
Brain Blood Flow ◽  
Choroidal Blood Flow ◽  
Flow Rates

The effect of changes in brain blood flow on cerebrospinal fluid (CSF) volume flow rates, and that of changes in CSF volume flow rates on brain blood flow were determined in both normal and kaolin-induced hydrocephalic cats. In both groups of cats, blood flow in grey and white matter, cerebral cortex, and choroid plexus was measured with 105Ru microspheres during normocapnia, and again with 141Ce microspheres after arterial Pco2 was either increased by 300% or decreased by 50%. Blood flow measurements were also made during perfusion of the ventricular system with mock CSF and repeated during perfusion with anisosmotic mannitol solutions to alter CSF volume flow rate. In 30 normal and 26 hydrocephalic cats, blood flow to the cerebral cortex, white matter, and choroid plexus was similar; only blood flow to the caudate nucleus was greater in normal cats. The weight of the choroid plexus from hydrocephalic cats decreased by 17%. Blood flow in the choroid plexus of all cats decreased by almost 50% following hypercapnia or hypocapnia, without a change in the CSF volume flow rate. There was no change in cerebral or choroidal blood flow when CSF volume flow rate was either increased by 170% or decreased by 80%. These results suggest that choroid plexus blood flow does not limit or affect the volume flow rate of CSF from the choroid plexus. CSF volume flow rate can be altered without corresponding blood flow changes of the brain or choroid plexus. Choroid plexus blood flow and the reactivity of both brain and choroidal blood flow to changes in arterial Pco2 were not affected by the hydrocephalus. The lower CSF formation rate of hydrocephalic cats can be attributed in part to the decrease in the mass of choroid plexus tissue.

Influence of two-phase suction injection on performances of the scroll refrigeration compressor with a high-temperature shell

2021 ◽  
pp. 095440892110302
Author(s):  
Shuaihui Sun ◽  
Wang Zhe ◽  
Li Liansheng ◽  
Bu Gaoxuan
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Flow Rate ◽  
Volume Flow Rate ◽  
Volume Flow ◽  
Coefficient Of Performance ◽  
Two Phase ◽  
Flow Rates ◽  
Injection Volume ◽  
Discharge Temperature

The two-phase suction injection can reduce the discharge temperature of scroll refrigeration compressors, which work under a high-pressure ratio. The heat transfer along the pipe axis from the shell affects the two-phase suction injection significantly for the compressor with a high-temperature shell. In this paper, the suction mixing and heat transfer model was developed to calculate the heat transfer along the pipe axis from the high-temperature compressor shell. Then the model was coupled with the two-phase compressor model to obtain the compressor performance under different suction injection volume flow rates. The compressor with two-phase suction injection was tested under different injection volume flow rates to validate the model. The results indicated that the discharge temperature decreased by 2 °C when the mass injection ratio increased by 1%. As the injection volume flow rates increased, the total mass flow rate increased due to the reduction of the specific volume of the suction fluid; the input work decreased because of the reduction of specific work and the improvement of the motor's electric efficiency. The cooling capacity decreased since the cooling capacity of the injection refrigerant was wasted for cooling the suction process and the compressor shell, especially at high injection volume flow rates. The coefficient of performance reached the maximum value at the injection volume flow rate of 0.015 m3·h−1 and became lower than the coefficient of performance without injection when the injection volume flow rate raised to 0.035 m3·h−1. Hence, the two-phase suction injection can reduce the discharge temperature efficiently at low injection volume flow rates with a slight improvement of coefficient of performance.

scholarly journals Numerical Analysis of the Energy Consumption of Ventilation Processes in the School Swimming Pool

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1023
Author(s):  
Piotr Ciuman ◽  
Jan Kaczmarczyk
Keyword(s):  
Energy Consumption ◽  
Flow Rate ◽  
Energy Demand ◽  
Volume Flow Rate ◽  
Volume Flow ◽  
Swimming Pool ◽  
Specific Humidity ◽  
Total Energy Consumption ◽  
Air Volume ◽  
Indoor Swimming Pool

Ventilation of an indoor swimming pool is a very energy consuming process. This is a result of, among other things the required high value of the ventilation air volume flow rate, calculated on the basis of the moisture gains in the facility. The total energy consumption consists of the heat required to heat this air and the electricity needed to transport it. It is possible to reduce the ventilation air volume flow rate by assuming the correct value of specific humidity of the supply and indoor air, but then a deterioration of thermal-moisture conditions in the building can be expected. The aim of this paper was to examine how the reduction of the supply air volume flow rate affects the energy consumption for indoor swimming pool ventilation. It was also checked how this consumption can be reduced by using two-stage heat recovery in the air handling unit. Multi-variant simulations of energy consumption for indoor swimming pool ventilation were carried out using the IDA ICE software for day and night operation of the swimming pool throughout the year. The results of the research proved that reduction of the supply air volume flow rate resulted in the lower energy expenditure on ventilation. The variant with additional local air supply to the lifeguard zone was also analysed, which caused only a slight increase in energy demand for ventilation.

scholarly journals C INVESTIGATION OF HEAT TRANSFER COEFFICIENT AUGMENTATION IN DIVERGENT RECTANGULAR DUCT FOR TWO PHASES FLOW (AIR-WATER)

2020 ◽  
Vol 20 (2) ◽  
pp. 111-121
Author(s):  
Hadi O . Basher ◽  
Riyadh S Al-Turaihi ◽  
Ahmed A. Shubba
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Flow Rate ◽  
Volume Flow Rate ◽  
Volume Flow ◽  
Water Volume ◽  
Maximum Heat ◽  
Air Volume ◽  
The Heat Transfer Coefficient

In this project, the flow distribution for air and water, and the enhancement of the heattransfer coefficient are experimentally studied. Experimental studies have been performed totest the influence of discharge, pitch, the height of ribs at a constant heat flux on thetemperature and pressure distributions. Along the channel of the test and the heat transfercoefficient, the water volume flow rate was about (5-12 L/min), the air volume flow rate wasabout (5.83-16.66 L/min), and heat were (80, 100,120, watt). An experimental rig wasconstructed within the test whole system. On the other hands, the channel has a divergentsection with an angle =15o with vertical axis. The study included changing in the ribs heightby using three values (12, 15, 18 mm) and changing the ribs pitch into three values (5, 8, 10mm).The results indicated an increasing in the local heat transfer coefficient as a result ofincreasing the discharge. While there was an inverse influence for the temperature distributionalong the test channel which drops when the discharge rise. The results also confirm that theincreasing in the pitch distance leads to reduce the heat transfer coefficient. Increasing theribs height increases the coefficient of heat transfer. However, the experiment heat transfercoefficient improves about (15.6 %) when the water volume flow rate increased from (5 to 12L/min), and about (18.7%) when the air volume flow rate increased from (5.83 to 16.66L/min). The best heat transfer coefficient was about (35.6 %) which can be achieved whenthe pitch decreased from (10 to 5mm). The increasing of the height from (12 to 18) mmimproves the heat transfer coefficient about (11.2 %). The best rib dimension was 18 mmheight, and 5 mm pitch, which give a maximum heat transfer coefficient (1212.02 W/m2. oC).

Three-dimensional multiphase flow modeling of membrane humidifier for PEM fuel cell application

2019 ◽  
Vol 30 (1) ◽  
pp. 54-74
Author(s):  
Seyed Ali Atyabi ◽  
Ebrahim Afshari ◽  
Mohammad Yaghoub Abdollahzadeh Jamalabadi
Keyword(s):  
Flow Rate ◽  
Volume Flow Rate ◽  
Three Dimensional ◽  
Cross Flow ◽  
High Volume ◽  
Volume Flow ◽  
Dew Point ◽  
Multiphase Model ◽  
Flow Rates ◽  
Content Type

Purpose In this paper, a single module of cross-flow membrane humidifier is evaluated as a three-dimensional multiphase model. The purpose of this paper is to analyze the effect of volume flow rate, dry temperature, dew point wet temperature and porosity of gas diffusion layer on the humidifier performance. Design/methodology/approach In this study, one set of coupled equations are continuity, momentum, species and energy conservation is considered. The numerical code is benchmarked by the comparison of numerical results with experimental data of Hwang et al. Findings The results reveal that the transfer rate of water vapor and dew point approach temperature (DPAT) increase by increasing the volume flow rate. Also, it is found that the water recovery ratio (WRR) and relative humidity (RH) decrease with increasing volume flow rate. In addition, all mixed results decrease with increasing dry side temperature especially at high volume flow rates and this trend in high volume flow rates is more sensible. Although the transfer rate of water vapor and DPAT increases with increasing the wet inlet temperature, WRR and RH reduce. Increasing dew point temperature effect is more sensible at the wet side is compared with the dry side. The humidification performance will be enhanced with increasing diffusion layer porosity by increasing the wet inlet dew point temperature, but has no meaningful effect on other operating parameters. The pressure drop along humidifier gas channels increases with rising flow rate, consequently, the required power of membrane humidifier will enhance. Originality/value According to previous studies, the three-dimensional numerical multiphase model of cross-flow membrane humidifier has not been developed.

scholarly journals Experimental Studies of Ethyl Acetate Saponification Using Different Reactor Systems: The Effect of Volume Flow Rate on Reactor Performance and Pressure Drop

2019 ◽  
Vol 9 (3) ◽  
pp. 532
Author(s):  
Ekaterina Borovinskaya ◽  
Valentin Khaydarov ◽  
Nicole Strehle ◽  
Alexander Musaev ◽  
Wladimir Reschetilowski
Keyword(s):  
Pressure Drop ◽  
Flow Rate ◽  
Volume Flow Rate ◽  
Experimental Studies ◽  
Chemical Processes ◽  
Volume Flow ◽  
Reactor Performance ◽  
Flow Rates ◽  
Flow Energy ◽  
Mass And Heat Transfer

Microreactors intensify chemical processes due to improved flow regimes, mass and heat transfer. In the present study, the effect of the volume flow rate on reactor performance in different reactors (the T-shaped reactor, the interdigital microreactor and the chicane microreactor) was investigated. For this purpose, the saponification reaction in these reactor systems was considered. Experimental results were verified using the obtained kinetic model. The reactor system with a T-shaped reactor shows good performance only at high flow rates, while the experimental setups with the interdigital and the chicane microreactors yield good performance throughout the whole range of volume flow rates. However, microreactors exhibit a higher pressure drop, indicating higher mechanical flow energy consumption than seen using a T-shaped reactor.

Sign in / Sign up

Export Citation Format

Share Document