scholarly journals Effect of Stall Cells on Pressure Fluctuations Characteristics in a Centrifugal Pump

Symmetry ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1116 ◽  
Author(s):  
Peijian Zhou ◽  
Jiacheng Dai ◽  
Chaoshou Yan ◽  
Shuihua Zheng ◽  
Changliang Ye ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuations ◽  
Low Frequency ◽  
Rotating Stall ◽  
Design Flow ◽  
Eddy Simulation ◽  
Leading Role ◽  
Stall Cells ◽  
Design Flow Rate

Rotating stall is an unsteady flow phenomenon, which always leads to instability and efficiency degradation. In order to reveal pressure fluctuations in the impeller of centrifugal pump induced by stall cells, the flow structures in a volute-type centrifugal pump were calculated using Large Eddy Simulation (LES) method. The predicted results of the numerical model were compared with experimental flow-head curve. The simulation results were in good agreement with the experimental results. The stall phenomenon occurred when the flow rate dropped to 70% of design flow rate. Three stall cells located at the entrance of passages could be observed, which remained stationary relative to the rotating impeller. With the decrease of flow rate, the area occupied by stall cells gradually increased. The peak value of pressure fluctuation at 25% of design flow rate is obviously larger than that at 50% of design flow rate. For the unstalled or stalled passage, the impeller-volute interaction played a leading role in the pressure fluctuations of the impeller. For the stalled passage, the amplitude of the low frequency induced by stall cell is relatively insignificant.

scholarly journals Comprehensive Numerical Investigations of Unsteady Internal Flows and Cavitation Characteristics in Double-Suction Centrifugal Pump

2017 ◽  
Vol 2017 ◽  
pp. 1-13 ◽  
Author(s):  
Xuelin Tang ◽  
Mingde Zou ◽  
Fujun Wang ◽  
Xiaoqin Li ◽  
Xiaoyan Shi
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuations ◽  
Dominant Frequency ◽  
Secondary Flows ◽  
Design Flow ◽  
Sharp Drop ◽  
Blade Loading ◽  
Blade Passing Frequency ◽  
Design Flow Rate

The RNG k-ε turbulence model combined with cavitation model was used to simulate unsteady cavitating flows inside a double-suction centrifugal pump under different flow rate conditions based on hexahedral structured grid. The numerical external characteristic performances agree well with the experimental performances. The predicted results show that the turbulence kinetic energy and the turbulence dissipation rate inside the impeller at design flow rate are lower than those at other off-design flow rates, which are caused by various vortexes. Based on frequency-domain analyses in the volute casing, the blade passing frequency is the dominant one of the pressure fluctuations except the vicinity of volute tongue for all operating cases, and the dominant frequency near the volute tongue ranges from 0 to 0.5 times the blade passing frequency for other off-design points, while the blade passing one near the volute tongue is the dominant one of the pressure fluctuations at design point. The increase of flow rate reduces the pressure fluctuations amplitude. For cavitation cases, the blade loading of the middle streamline increases a bit during the initial stage, but, for serious cavitation, the blade loading near the blade inlet reduces to 0 and even negative values, and the serious cavitation bubbles block the blade channels, which results in a sharp drop in pump head. Under noncavitation condition, the predicted power related to the pressure in the impeller channels increases from the inlet to the exit, while, under different cavitation conditions at the design flow rate, these power-transformation distributions in the impeller channels show that these power conversions are affected by the available NPSHa and the corresponding work in leading regions of the blades increases increases gradually a bit, and then it increases sharply in the middle regions, but it decreases in the blade trailing regions and is greatly influenced by secondary flows.

scholarly journals Large Eddy Simulation of Periodic Transient Pressure Fluctuation in a Centrifugal Pump Impeller at Low Flow Rate

Symmetry ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 311
Author(s):  
Renfei Kuang ◽  
Xiaoping Chen ◽  
Zhiming Zhang ◽  
Zuchao Zhu ◽  
Yu Li
Keyword(s):  
Large Eddy Simulation ◽  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Low Frequency ◽  
Pump Impeller ◽  
Eddy Simulation ◽  
Inlet Flow Rate ◽  
Large Eddy ◽  
Centrifugal Pump Impeller

This paper presents a large eddy simulation of a centrifugal pump impeller during a transient condition. The flow rate is sinusoidal and oscillates between 0.25Qd (Qd indicates design load) and 0.75Qd when the rotating speed is maintained. Research shows that in one period, the inlet flow rate will twice reach 0.5Qd, and among the impeller of one moment is a stall state, but the other is a non-stall state. In the process of flow development, the evolution of low-frequency pressure fluctuation shows an obviously sinusoidal form, whose frequency is insensitive to the monitoring position and equals to that of the flow rate. However, inside the impeller, the phase and amplitude in the stall passages lag behind more and are stronger than that in the non-stall passages. Meanwhile, the strongest region of the high-frequency pressure fluctuation appears in the stall passages at the transient rising stage. The second dominant frequency in stall passages is 2.5 times to that in non-stall passages. In addition, similar to the pressure fluctuation, the evolution of the low-frequency head shows a sinusoidal form, whose phase is lagging behind that by one-third of a period in the inlet flow rate.

scholarly journals Experimental Analysis on Pressure Fluctuation Characteristics of a Centrifugal Pump with Vaned-Diffuser

Water ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 126
Author(s):  
Houlin Liu ◽  
Ruichao Xia ◽  
Kai Wang ◽  
Yucheng Jing ◽  
Xianghui He
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Dominant Frequency ◽  
Design Flow ◽  
Signal Source ◽  
Vaned Diffuser ◽  
Impeller Outlet ◽  
Variation Tendency ◽  
Design Flow Rate

Experimental measurements to analyze the pressure fluctuation performance of a centrifugal pump with a vaned-diffuser, which its specific speed is 190. Results indicate that the main cause of pressure fluctuation is the rotor-stator interference at the impeller outlet. The head of the pump with vaned-diffuser at the design flow rate is 15.03 m, and the efficiency of the pump with a vaned-diffuser at the design flow rate reaches 71.47%. Pressure fluctuation decreases gradually with increasing distance from the impeller outlet. Along with the increase of the flow rate, amplitude of pressure fluctuation decreases. The amplitude of pressure fluctuation at the measuring points near the diffusion section of the pump body is larger than other measuring points. The variation tendency of pressure fluctuation at P1–P10 is the same, while there are wide frequency bands with different frequencies. The dominant frequency of pressure fluctuation is the blade passing frequency. The rotor-stator interference between the impeller and the vaned-diffuser gives rise to the main signal source of pressure fluctuation.

Influence of wall roughness on the static performance and pressure fluctuation characteristics of a double-suction centrifugal pump

2018 ◽  
Vol 232 (7) ◽  
pp. 826-840 ◽  
Author(s):  
Zhifeng Yao ◽  
Min Yang ◽  
Ruofu Xiao ◽  
Fujun Wang
Keyword(s):  
Centrifugal Pump ◽  
Pressure Fluctuation ◽  
Pressure Fluctuations ◽  
Design Flow ◽  
Experimental Investigations ◽  
Wall Roughness ◽  
Detached Eddy Simulation ◽  
Centrifugal Pumps ◽  
Eddy Simulation ◽  
Static Performance

The unsteady flow field and pressure fluctuations in double-suction centrifugal pumps are greatly affected by the wall roughness of internal surfaces. To determine the wall roughness effect, numerical and experimental investigations were carried out. Three impeller schemes for different wall roughness were solved using detached eddy simulation, and the performance and pressure fluctuations resolved by detached eddy simulation were compared with the experimental data. The results show that the effects of wall roughness on the static performance of a pump are remarkable. The head and efficiency of the tested double-suction centrifugal pump are raised by 2.53% and 6.60% respectively as the wall roughness is reduced by means of sand blasting and coating treatments. The detached eddy simulation method has been proven to be accurate for the prediction of the head and efficiency of the double-suction centrifugal pump with roughness effects. The influence of the roughness on pressure fluctuation is greatly dependent on the location relative to the volute tongue region. For locations close to the volute tongue, the peak-to-peak value of the pressure fluctuations of a wall roughness of Ra = 0.10 mm may be 23.27% larger than the case where Ra = 0.02 mm at design flow rate.

Turbulence Measurements in a Centrifugal Pump With a Synchronously Orbiting Impeller

1991 ◽  
Author(s):  
Ronald D. Flack ◽  
Steven M. Miner ◽  
Ronald J. Beaudoin
Keyword(s):  
Centrifugal Pump ◽  
Reynolds Stress ◽  
Flow Rate ◽  
Cross Product ◽  
Design Flow ◽  
Low Flow ◽  
Rate Variation ◽  
Flow Rates ◽  
The Individual ◽  
Design Flow Rate

Turbulence profiles were measured in a centrifugal pump with an impeller with backswept blades using a two directional laser velocimeter. Data presented includes radial, tangential, and cross product Reynolds stresses. Blade to blade profiles were measured at four circumferential positions and four radii within and one radius outside the four bladed impeller. The pump was tested in two configurations; with the impeller running centered within the volute, and with the impeller orbiting with a synchronous motion (ε/r2 = 0.016). Flow rates ranged from 40% to 106% of the design flow rate. Variation in profiles among the individual passages in the orbiting impeller were found. For several regions the turbulence was isotropic so that the cross product Reynolds stress was low. At low flow rates the highest cross product Reynolds stress was near the exit. At near design conditions the lowest cross product stress was near the exit, where uniform flow was also observed. Also, near the exit of the impeller the highest turbulence levels were seen near the tongue. For the design flow rate, inlet turbulence intensities were typically 9% and exit turbulence intensities were 6%. For 40% flow capacity the values increased to 18% and 19%, respectively. Large local turbulence intensities correlated with separated regions. The synchronous orbit did not increase the random turbulence, but did affect the turbulence in the individual channels in a systematic pattern.

scholarly journals Efficiency improvement and evaluation of a centrifugal pump with vaned diffuser

2019 ◽  
Vol 11 (3) ◽  
pp. 168781401982590 ◽  
Author(s):  
Kai Wang ◽  
Yu-cheng Jing ◽  
Xiang-hui He ◽  
Hou-lin Liu
Keyword(s):  
Centrifugal Pump ◽  
Axial Force ◽  
Flow Rate ◽  
Pressure Pulsation ◽  
Energy Performance ◽  
Radial Force ◽  
Design Flow ◽  
Vaned Diffuser ◽  
Original Scheme ◽  
Design Flow Rate

In order to enhance the efficiency of centrifugal pump, the structure of a centrifugal pump with vaned diffuser, whose specific speed is 190, was numerically improved by trimming back-blades of impeller and smoothing sharp corner in annular chamber. The energy performance, the internal flow field, the axial force, the radial force, and the pressure pulsation of the pump were analyzed. Results show that efficiency of the improving scheme 1 under the design flow rate is 77.47%, which can balance 69.82% of the axial force, while efficiency of the improving scheme 2 under the design flow rate is the maximum, which could still balance 62.74% of the axial force. The pressure pulsations of the improving scheme 2 at the typical monitoring points are less than that of the improving scheme 1 and the original scheme. The difference of the radial force peak between the improving scheme 1 and the improving scheme 2 is very small. The vector distributions of the radial force of the improving scheme 1 and the improving scheme 2 are more uniform than that of the original scheme. Considering the efficiency, pressure pulsation, and axial force, experiment measurements on the improving scheme 2 were carried out to verify the effectiveness of the improvement result. Results of energy performance experiment show that efficiency of the improving scheme 2 under the design flow rate is 76.48%, which is 5.26 percentage points higher than that of the original scheme.

Three-Dimensional Computational Fluid Dynamics Prediction of Turbocharger Centrifugal Compression System Instabilities

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Rick Dehner ◽  
Ahmet Selamet
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Rate ◽  
Pressure Fluctuations ◽  
Three Dimensional ◽  
Rotating Stall ◽  
Flow Reversal ◽  
Constant Speed ◽  
Local Flow ◽  
Stall Cells

The present work combines experimental measurements and unsteady, three-dimensional computational fluid dynamics predictions to gain further insight into the complex flow-field within an automotive turbocharger centrifugal compressor. Flow separation from the suction surface of the main impeller blades first occurs in the mid-flow range, resulting in local flow reversal near the periphery, with the severity increasing with decreasing flow rate. This flow reversal improves leading-edge incidence over the remainder of the annulus, due to (a) reduction of cross-sectional area of forward flow, which increases the axial velocity, and (b) prewhirl in the direction of impeller rotation, as a portion of the tangential velocity of the reversed flow is maintained when it mixes with the core flow and transitions to the forward direction. As the compressor operating point enters the region where the slope of the constant speed compressor characteristic (pressure ratio versus mass flow rate) becomes positive, rotating stall cells appear near the shroud side diffuser wall. The angular propagation speed of the diffuser rotating stall cells is approximately 20% of the shaft speed, generating pressure fluctuations near 20% and 50% of the shaft frequency, which were also experimentally observed. For the present compressor and rotational speed, flow losses associated with diffuser rotating stall are likely the key contributor to increasing the slope of the constant speed compressor performance curve to a positive value, promoting the conditions required for surge instabilities. The present mild surge predictions agree well with the measurements, reproducing the amplitude and period of compressor outlet pressure fluctuations.

Turbulence Measurements in a Centrifugal Pump With a Synchronously Orbiting Impeller

1992 ◽  
Vol 114 (2) ◽  
pp. 350-358 ◽  
Author(s):  
R. D. Flack ◽  
S. M. Miner ◽  
R. J. Beaudoin
Keyword(s):  
Centrifugal Pump ◽  
Reynolds Stress ◽  
Flow Rate ◽  
Cross Product ◽  
Design Flow ◽  
Low Flow ◽  
Rate Variation ◽  
Flow Rates ◽  
The Individual ◽  
Design Flow Rate

Turbulence profiles were measured in a centrifugal pump with an impeller with backswept blades using a two-directional laser velocimeter. Data presented include radial, tangential, and cross product Reynolds stresses. Blade-to-blade profiles were measured at four circumferential positions and four radii within and one radius outside the four-bladed impeller. The pump was tested in two configurations: with the impeller running centered within the volute, and with the impeller orbiting with a synchronous motion (ε/r2 = 0.016). Flow rates ranged from 40 to 106 percent of the design flow rate. Variation in profiles among the individual passages in the oribiting impeller were found. For several regions the turbulence was isotropic so that the cross product Reynolds stress was low. At low flow rates the highest cross product Reynolds stress was near the exit. At near-design conditions the lowest cross product stress was near the exit, where uniform flow was also observed. Also, near the exit of the impeller the highest turbulence levels were seen near the tongue. For the design flow rate, inlet turbulence intensities were typically 9 percent and exit turbulence intensities were 6 percent. For 40 percent flow capacity the values increased to 18 and 19 percent, respectively. Large local turbulence intensities correlated with separated regions. The synchronous orbit did not increase the random turbulence, but did affect the turbulence in the individual channels in a systematic pattern.

Pressure Fluctuation of the Low Specific Speed Centrifugal Pump

2012 ◽  
Vol 152-154 ◽  
pp. 935-939 ◽  
Author(s):  
Qiang Fu ◽  
Shou Qi Yuan ◽  
Rong Sheng Zhu
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
High Frequency ◽  
Pressure Fluctuations ◽  
Radial Force ◽  
Design Flow ◽  
Rate Condition ◽  
Low Specific Speed ◽  
Specific Speed

In order to study the rules of pressure fluctuation and the radial force under different positions in a centrifugal pump with low specific speed, and to find the relationship between each other, the three-dimensional ,unsteady Reynolds-averaged Navier-stokes equations with shear stress transport turbulent models were solved. The pressure fluctuation was obtained. The results showed that the pressure fluctuations were visible. The pressure fluctuations in the volute were relatively low at the design flow rate condition. The blade passing frequency dominates the pressure fluctuations, high frequency contents were found on the outlet of impeller but no high frequency information occured in casing. The radial force on the impeller was unsteady especially at the small flow rate.

Experimental Investigation of Time-Frequency Characteristics of Pressure Fluctuations in a Double-Suction Centrifugal Pump

2011 ◽  
Vol 133 (10) ◽  
Author(s):  
Zhifeng Yao ◽  
Fujun Wang ◽  
Lixia Qu ◽  
Ruofu Xiao ◽  
Chenglian He ◽  
...  
Keyword(s):  
Frequency Domain ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Pressure Fluctuations ◽  
Operating Conditions ◽  
Design Flow ◽  
Flow Rates ◽  
Time Frequency ◽  
Blade Passing Frequency ◽  
Design Flow Rate

Pressure fluctuation is the primary reason for unstable operations of double-suction centrifugal pumps. By using flush mounted pressure transducers in the semispiral suction chamber and the volute casing of a double-suction pump, the pressure fluctuation signals were obtained and recorded at various operating conditions. Spectral analyses were performed on the pressure fluctuation signals in both frequency domain and time-frequency domain based on fast Fourier transform (FFT) and an adaptive optimal-kernel time-frequency representation (AOK TFR). The results show that pressure fluctuations at the impeller rotating frequency and some lower frequencies dominated in the semispiral suction chamber. Pressure fluctuations at the blade passing frequency, the impeller rotating frequency, and their harmonic frequencies were identified in the volute casing. The amplitude of pressure fluctuation at the blade passing frequency significantly increased when the flow rate deviated from the design flow rate. At 107% of the design flow rate, the amplitude increased more than 254% than that at the design flow rate. The time-frequency characteristics of these pressure fluctuations were affected greatly by both operating conditions and measurement locations. At partial flow rates the pulsation had a great irregularity and the amplitudes at the investigated frequencies were much larger than ones at the design flow rate. An asymmetrical pressure fluctuation structure in the volute casing was observed at all flow rates. The pulsation behavior at the blade passing frequency was the most prominent near the volute tongue zone, and the pressure waves propagated in both the radial and circumferential directions.

Sign in / Sign up

Export Citation Format

Share Document