scholarly journals Determination of Force Coefficients for a Submerged Rigid Breakwater under the Action of Solitary Waves

Water ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 315
Author(s):  
Francesco Aristodemo ◽  
Giuseppe Tripepi ◽  
Luana Gurnari ◽  
Pasquale Filianoti
Keyword(s):  
Solitary Waves ◽  
Pressure Sensors ◽  
Wave Forces ◽  
Wave Loads ◽  
Force Coefficients ◽  
Wave Flume ◽  
Physical Tests ◽  
The Difference ◽  
The University ◽  
Semi Empirical

We present an analysis related to the evaluation of Morison and transverse force coefficients in the case of a submerged square barrier subject to the action of solitary waves. To this purpose, two-dimensional experimental research was undertaken in the wave flume of the University of Calabria, in which a rigid square barrier was provided by a discrete battery of pressure sensors to determine the horizontal and vertical hydrodynamic forces. A total set of 18 laboratory tests was carried out by varying the motion law of a piston-type paddle. Owing to the low Keulegan–Carpenter numbers of the tests, the force regime of the physical tests was defined by the dominance of the inertia loads in the horizontal direction and of the lift loads in the vertical one. Through the use of the time series of wave forces and the undisturbed kinematics, drag, horizontal inertia, lift, and vertical inertia coefficients in the Morison and transverse semi-empirical schemes were calculated using time-domain approaches, adopting the WLS1 method for the minimization of the difference between the maximum forces and the linked phase shifts by comparing laboratory and calculated wave loads. Practical equations to calculate these coefficients as a function of the wave non-linearity were introduced. The obtained results highlighted the prevalence of the horizontal forces in comparison with the vertical ones which, however, prove to be fundamental for stability purposes of the barrier. An overall good agreement between the experimental forces and those calculated by the calibrated semi-empirical schemes was found, particularly for the positive horizontal and vertical loads. The analysis of the hydrodynamic coefficients showed a decreasing trend for the drag, horizontal inertia, and lift coefficients as a function of the wave non-linearity, while the vertical inertia coefficient underlined an initial increasing trend and a successive slight decreasing trend.

Experimental Study of Wave Loading by Internal Solitary Waves on a Semi-Submersible Platform

2019 ◽  
Author(s):  
Jingjing Zhang ◽  
Ke Chen ◽  
Yunxiang You ◽  
Xinshu Zhang
Keyword(s):  
Solitary Waves ◽  
Lower Layer ◽  
Internal Solitary Waves ◽  
Wave Forces ◽  
Wave Loads ◽  
Wave Loading ◽  
Layer Depth ◽  
Fluid System ◽  
Layer Thickness Ratio ◽  
Three Degree Of Freedom

Abstract The experimental measurements presented here describe the major features of the loads exerted by internal solitary waves (ISWs) on columns and caissons of a semi-submersible platform in a two-layer fluid system. Particular attention is paid on the forces acted on the platform under different layer thickness ratio. By use of the dynamometer for forces of three degree of freedom (DOF), the wave forces exerted by the ISWs on the columns and caissons of the model are measured quantificationally, so the variations of forces with ISW’s amplitude and upper layer depth are derived. Comparisons are made between the experimental results and calculations based on the modified Morison equation and pressure integral method. The calculated results are well consistent with the measurements, so the method is capable of providing satisfactory predictions on the forces. Besides, the results show that the wave height has a considerable influence on the wave loads produced by the ISWs, and the forces varies with the different locations of the interface between the upper and lower layer.

Experimental and Numerical Investigation of Tsunami-Like Waves on Horizontal Circular Cylinders

2017 ◽  
Author(s):  
Giuseppe Tripepi ◽  
Francesco Aristodemo ◽  
Paolo Veltri ◽  
Calogero Pace ◽  
Andrea Solano ◽  
...  
Keyword(s):  
Numerical Study ◽  
Circular Cylinders ◽  
Pressure Transducers ◽  
Wave Flume ◽  
Weakly Compressible ◽  
Calibration Methods ◽  
Sph Model ◽  
Horizontal Cylinders ◽  
The University ◽  
Semi Empirical

This work deals with an experimental and numerical study on the horizontal and vertical hydrodynamic forces induced by tsunami-like waves on horizontal cylinders. The laboratory investigation has been performed in the wave flume of the University of Calabria. Twelve pressure transducers have been mounted along the external contour of a cylinder, while four wave gauges have been located close to the cylinder and an ultrasonic sensor behind the paddle to measure its displacement. Tests have been carried out for Keulegan-Carpenter numbers, KC, ranging from about 4 to 7. By the numerical viewpoint, a diffusive weakly-compressible SPH model has been adopted. To prevent spurious flows near the cylindrical contour, a packing algorithm has been applied before SPH simulations. The acoustic components occurring in the numerical pressure field have been filtered through the application of Wavelet Transform. By using different calibration methods, experimental and SPH forces and kinematics at the cylinder have been used to calculate the hydrodynamic coefficients in the Morison and transverse semi-empirical equations for engineering purposes.

scholarly journals Enamel interproximal reduction during treatment with clear aligners: digital planning versus OrthoCAD analysis

2021 ◽  
Vol 21 (1) ◽  
Author(s):  
Giuseppina Laganà ◽  
Arianna Malara ◽  
Roberta Lione ◽  
Carlotta Danesi ◽  
Simonetta Meuli ◽  
...  
Keyword(s):  
Treatment Plan ◽  
End Of Treatment ◽  
The Mean ◽  
The Difference ◽  
Dependent Sample ◽  
University Of Rome ◽  
The University ◽  
Enamel Reduction ◽  
Lower Arch

Abstract Background The aim of the study was to compare the amount of interproximal enamel reduction (IPR) provided on ClinCheck software with the amount of IPR carried out by the orthodontist during treatment with clear aligners. Methods 30 subjects (14 males, 16 females; mean age of 24.53 ± 13.41 years) randomly recruited from the Invisalign account of the Department of Orthodontics at the University of Rome “Tor Vergata” from November 2018 to October 2019, were collected according to the following inclusion criteria: mild to moderate dento-alveolar discrepancy (1.5–6.5 mm); Class I canine and molar relationship; full permanent dentition (excluding third molars); both arches treated only using Comprehensive Package by Invisalign system; treatment plan including IPR. Pre- (T0) and post-treatment (T1) digital models (.stl files), created from an iTero scan, were collected from all selected patients. The OrthoCAD digital software was used to measure tooth mesiodistal width in upper and lower arches before (T0) and at the end of treatment (T1) before any refinement. The widest mesio-distal diameter was measured for each tooth excluding molars by “Diagnostic” OrthoCAD tool. The total amount of IPR performed during treatment was obtained comparing the sum of mesio-distal widths of all measured teeth at T0 and T1. Significant T1–T0 differences were tested with dependent sample t-test (P < 0.05). Results In the upper arch, IPR was digitally planned on average for 0.62 mm while in the lower arch was on average for 1.92 mm. As for the amount of enamel actually removed after IPR performing, it was on average 0.62 mm in the maxillary arch. In the mandibular arch, the mean of IPR carried out was 1.93 mm. The difference between planned IPR and performed IPR is described: this difference was on average 0.00 mm in the upper arch and 0.01 in the lower arch. Conclusions The amount of enamel removed in vivo corresponded with the amount of IPR planned by the Orthodontist using ClinCheck software.

Relation between Magnetic, Spectroscopic and Structural Properties of Binuclear Copper(II) Complexes of Pentadentate Schiff-base Ligand, Semi-empirical and ab-initio Calculations

2003 ◽  
Vol 58 (5-6) ◽  
pp. 363-372 ◽  
Author(s):  
Y. Elerman ◽  
H. Kara ◽  
A. Elmali
Keyword(s):  
Ab Initio ◽  
Coupling Constants ◽  
Antiferromagnetic Coupling ◽  
X Ray Diffraction ◽  
Hartree Fock ◽  
Ligand Orbital ◽  
Rhf Calculations ◽  
The Difference ◽  
Semi Empirical

The synthesis and characterization of [Cu2(L1)(3,5 prz)] (L1=1,3-Bis(2-hydroxy-3,5-chlorosalicylideneamino) propan-2-ol) 1 and of [Cu2(L2)(3,5 prz)] (L2=1,3-Bis(2-hydroxy-bromosalicylideneamino) propan-2-ol) 2 are reported. The compounds were studied by elemental analysis, infrared and electronic spectra. The structure of the Cu2(L1)(3,5 prz)] complex was determined by x-ray diffraction. The magnetochemical characteristics of these compounds were determined by temperaturedependent magnetic susceptibility measurements, revealing their antiferromagnetic coupling. The superexchange coupling constants are 210 cm−1 for 1 and 440 cm−1 for 2. The difference in the magnitude of the coupling constants was explained by the metal-ligand orbital overlaps and confirmed by ab-initio restricted Hartree-Fock (RHF) calculations. In order to determine the nature of the frontier orbitals, Extended Hückel Molecular Orbital (EHMO) calculations are also reported.

scholarly journals XXIII.—On the Disruptive Discharge of Electricity: An Experimental Thesis for the Degree of Doctor of Science, Department A

1878 ◽  
Vol 28 (2) ◽  
pp. 633-671 ◽  
Author(s):  
Alexander Macfarlane
Keyword(s):  
Copper Wire ◽  
Late Summer ◽  
The Other ◽  
Straight Line ◽  
Summer Session ◽  
The Difference ◽  
A Chain ◽  
The One ◽  
Metallic Parts ◽  
The University

The experiments to which I shall refer were carried out in the physical laboratory of the University during the late summer session. I was ably assisted in conducting the experiments by three students of the laboratory,—Messrs H. A. Salvesen, G. M. Connor, and D. E. Stewart. The method which was used of measuring the difference of potential required to produce a disruptive discharge of electricity under given conditions, is that described in a paper communicated to the Royal Society of Edinburgh in 1876 in the names of Mr J. A. Paton, M. A., and myself, and was suggested to me by Professor Tait as a means of attacking the experimental problems mentioned below.The above sketch which I took of the apparatus in situ may facilitate tha description of the method. The receiver of an air-pump, having a rod capable of being moved air-tight up and down through the neck, was attached to one of the conductors of a Holtz machine in such a manner that the conductor of the machine and the rod formed one conducting system. Projecting from the bottom of the receiver was a short metallic rod, forming one conductor with the metallic parts of the air-pump, and by means of a chain with the uninsulated conductor of the Holtz machine. Brass balls and discs of various sizes were made to order, capable of being screwed on to the ends of the rods. On the table, and at a distance of about six feet from the receiver, was a stand supporting two insulated brass balls, the one fixed, the other having one degree of freedom, viz., of moving in a straight line in the plane of the table. The fixed insulated ball A was made one conductor with the insulated conductor of the Holtz and the rod of the receiver, by means of a copper wire insulated with gutta percha, having one end stuck firmly into a hole in the collar of the receiver, and having the other fitted in between the glass stem and the hollow in the ball, by which it fitted on to the stem tightly. A thin wire similarly fitted in between the ball B and its insulating stem connected the ball with the insulated half ring of a divided ring reflecting electrometer.

Effect of Air Fraction on Force Coefficients in Oscillatory Flow

2021 ◽  
Author(s):  
Malene Hovgaard Vested ◽  
Erik Damgaard Christensen
Keyword(s):  
High Speed ◽  
Offshore Structures ◽  
Air Injection ◽  
Wave Loads ◽  
Morison Equation ◽  
Force Coefficients ◽  
Air Content ◽  
Set Up ◽  
High Level ◽  
Spilling Breakers

Abstract The forces on marine and offshore structures are often affected by spilling breakers. The spilling breaker is characterized by a roller of mixed air and water with a forward speed approximately equal to the wave celerity. This high speed in the top of the wave has the potential to induce high wave loads on upper parts of the structures. This study analyzed the effect of the air content on the forces. The analyses used the Morison equation to examine the effect of the percentage of air on the forces. An experimental set-up was developed to include the injection of air into an otherwise calm water body. The air-injection did introduce a high level a turbulence. It was possible to assess the amount of air content in the water for different amounts of air-injection. In the mixture of air and water the force on an oscillating square cylinder was measured for different levels of air-content, — also in the case without air. The measurements indicated that force coefficients for clear water could be use in the Morison equation as long as the density for water was replaced by the density for the mixture of air and water.

scholarly journals Family Climate Patterns and Its Relationship with Self-Concept among Students at the University of Islamic Sciences in light of the Variables of Gender and Age

2017 ◽  
Vol 9 (1) ◽  
pp. 145
Author(s):  
Fatima Mohammad Rashed Al Talahin ◽  
Hana Khaled Al –Raqqad ◽  
Eman Saeed Al- Bourini ◽  
Bilal Adel Al-Kateeb
Keyword(s):  
Pearson Correlation ◽  
Statistical Significance ◽  
Self Concept ◽  
Family Climate ◽  
Gender And Age ◽  
Climate Patterns ◽  
The Difference ◽  
The University ◽  
The Impact ◽  
The Relationship

The aim of this study is to clarify the relationship between self-concept and patterns of family climate among students at the University of Islamic Sciences, and also aimed to investigate the effect of gender and age on this relationship.The sample of the study consisted of a group of students were selected randomly, totaling (139) students; (58) male and (81) female students.Two questionnaires were distributed on 139 students. The first questionnaire was on the impact of patterns of family climate on self-concept and the second one about self-concept. Then the researcher analyzed the results of each item in the questionnaire using appropriated statistical methods, calculated the correlation between self-concept and patterns of family climate using the Pearson correlation coefficient, and G-test to find the difference between correlation coefficients.The results showed a positive statistical significance relationship between family climate patterns on one hand and between self-concept in all its dimensions on the other hand.

Study Based on FLUENT of Broken Internal Waves in Different Slope Angles

2014 ◽  
Vol 638-640 ◽  
pp. 1769-1777
Author(s):  
Zi Tong Yan ◽  
Liang Qiu Cheng ◽  
Feng Yi ◽  
Tai Zhong Chen ◽  
Han Sun ◽  
...  
Keyword(s):  
Internal Waves ◽  
Solitary Waves ◽  
Wave Breaking ◽  
Slope Angle ◽  
Ecological Environment ◽  
Internal Solitary Waves ◽  
Propagation Process ◽  
Numerical Wave Flume ◽  
Wave Flume ◽  
New Methods

Internal waves will break in the process of communication, the broken will make water in upper and lower mixing, which has significant influence on the hydrodynamic and layered characteristics of density stratification of the water. In order to reveal the propagation of internal solitary waves, a 3d numerical wave flume was built. The research of the propagation of internal solitary waves in the regular topography and broken on slopes was based on FLUENT. Comparing the fragmentation degree of different slope angle and researching the energy dissipation of the wave propagation process , which are supposed to successfully match the results with the experiment results, can provide new methods and means for the further study of internal wave breaking characteristics and the improvement of ecological environment of water bodies.

Twelfth-century Cosmography, theDe secretis philosophie, and Māshā'allāh (Attr. to),Liber de Orbe

Traditio ◽  
2012 ◽  
Vol 67 ◽  
pp. 235-276
Author(s):  
Barbara Obrist
Keyword(s):  
New York ◽  
Thirteenth Century ◽  
Natural Philosophy ◽  
Lunar Eclipse ◽  
Latin Text ◽  
Central Section ◽  
The Difference ◽  
The University ◽  
University Of Manchester ◽  
The Universe

TheLiber de orbe, attributed to Māshā'allāh (fl. 762–ca. 815) in the list of Gerard of Cremona's translations, stands out as one of the few identifiable sources for the indirect knowledge of Peripatetic physics and cosmology at the very time Aristotle's works on natural philosophy themselves were translated into Latin, from the 1130s onward. This physics is expounded in an opening series of chapters on the bodily constitution of the universe, while the central section of the treatise covers astronomical subjects, and the remaining parts deal with meteorology and the vegetal realm. Assuming that Gerard of Cremona's translation of theLiber de orbecorresponds to the twenty-seven chapter version that circulated especially during the thirteenth and fourteenth centuries, it was, however, not this version, but a forty-chapter expansion thereof that became influential as early as the 1140s. It may have originated in Spain, as indicated, among others, by a reference to the difference of visibility of a lunar eclipse between Spain and Mecca. Unlike the twenty-seven chapterLiber de orbe, this expanded and also partly modified text remains in manuscript, and none of the three copies known so far gives a title or mentions Māshā'allāh as an author. Instead, the thirteenth-century witness that is now in New York attributes the work to an Alcantarus:Explicit liber Alcantari Caldeorum philosophi. While no Arabic original of the twenty-seven chapterLiber de orbehas come to light yet, Taro Mimura of the University of Manchester recently identified a manuscript that partly corresponds to the forty-chapter Latin text, as well as a shorter version thereof.

LACTATION PERFORMANCE OF RANGE BEEF AND DAIRY-BEEF COWS

1984 ◽  
Vol 64 (2) ◽  
pp. 253-265 ◽  
Author(s):  
SARAH BUTSON ◽  
R. T. BERG
Keyword(s):  
Milk Production ◽  
Beef Cows ◽  
Significant Decline ◽  
Lactation Performance ◽  
University Of Alberta ◽  
Brown Swiss ◽  
Percent Protein ◽  
The Difference ◽  
The University ◽  
Better Than

A milking experiment with range, single-suckled beef cows was conducted over two lactations in 1976 and 1977 at the University of Alberta Research Ranch. A total of 428 cows were milked, ranging from 2 to 10 yr of age and representing four breed groups of Herefords and crossbreds of traditional beef and dairy breeds. Measurements of milk were taken in June and September each year. Milk was extracted following an intrajugular injection of 20 IU of oxytocin. Samples were analyzed for butterfat percent, protein percent and lactose percent. Age and breed of dam differences in milk yields, constituent percentages and yields were assessed. Least squares means of yields pooled over the two periods each year indicated that dams with Holstein and Brown Swiss breeding (DS) yielded more milk than beef crossbreds and purebred Herefords. Average milk yields estimated over 24 h ranged from 5.7 kg/day for Herefords to 7.8 kg/day for DS dams. Compared to 2-yr olds at 100%, 3-yr olds produced 125%, 4-yr olds 136% and mature cows 139% greater yield. The difference between June and September yields was evident between breed groups. Hereford milk production exhibited the greatest decline over 87 days compared to all other crossbreds and DS were the most persistent. Mature cows maintained milk yields better than younger cows, and 2-yr old milk yields declined most noticeably. All crossbred groups produced less butterfat percent and lactose percent content than the Herefords, yet yielded more total energy. All constituent percentages were higher than those reported for commercial dairy cattle. All constituent percentages increased significantly from June to September at approximately 130 days in lactation. A significant decline was noted for all constituent yields in September. Dairy crossbreds demonstrated the highest persistency for all constituent yields. Beef Synthetic dams were intermediate in yield persistency. Average milk yields had negative (P < 0.05) correlations with average constituent percentages. Inter-correlations among constituent percentages were variable and generally small and negative. Key words: Lactation, range cows

Sign in / Sign up

Export Citation Format

Share Document