scholarly journals Research on a Visual Servo Method of a Manipulator Based on Velocity Feedforward

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Rui Wang ◽  
Changchun Liang ◽  
Dong Pan ◽  
Xiaodong Zhang ◽  
Pengfei Xin ◽  
...  
Keyword(s):  
Coordinate System ◽  
Control Method ◽  
Tracking Error ◽  
Target Prediction ◽  
Target Velocity ◽  
Visual Servo ◽  
Integral Control ◽  
Motion State ◽  
Simulation And Experiment ◽  
Velocity Prediction

In this paper, a method of predicting the motion state of a moving target in the base coordinate system by hand-eye vision and the position and attitude of the end is proposed. The predicted value is used as the velocity feedforward, and the position-based visual servo method is used to plan the velocity of the end of the manipulator. It overcomes the influence of end coordinate system motion on target prediction in a discrete system and introduces an integral control method to compensate for the prediction velocity, eliminating the end tracking error caused by target velocity prediction error. The effectiveness of this method is verified by simulation and experiment.

Interaction Forces Identification Modeling and Tracking Control for Rehabilitative Training Walker

2019 ◽  
Vol 23 (2) ◽  
pp. 183-195
Author(s):  
Ping Sun ◽  
Wenjiao Zhang ◽  
Shuoyu Wang ◽  
Hongbin Chang ◽  
◽  
...  
Keyword(s):  
Tracking Control ◽  
Control Method ◽  
Tracking Error ◽  
Model Identification ◽  
Fuzzy Model ◽  
Adaptive Backstepping ◽  
Interaction Forces ◽  
Design Procedures ◽  
Tracking Motion ◽  
Simulation And Experiment

In this study, we propose a model and an adaptive backstepping tracking control method for omnidirectional rehabilitative training walker. The aim of the study is to design a stable tracking controller that can guarantee accurate tracking motion of the omnidirectional walker considering the interaction forces of the user and walker. A novel fuzzy model identification method was proposed to describe the interaction forces by using the reduced values of tracking performance. Further, an adaptive backstepping controller was developed to compensate the interaction forces on the basis of the identified model and adapt the change of user’s mass. The asymptotic stability of the trajectory tracking error and the velocity tracking error were guaranteed. As an application, simulation and experiment results were provided to illustrate the effectiveness of the proposed design procedures.

scholarly journals Adaptive speed control method for electromagnetic direct drive vehicle robot driver based on fuzzy logic

2019 ◽  
Vol 52 (9-10) ◽  
pp. 1344-1353 ◽  
Author(s):  
Gang Chen ◽  
Weigong Zhang ◽  
Xu Li ◽  
Bing Yu
Keyword(s):  
Fuzzy Logic ◽  
Control Method ◽  
Tracking Error ◽  
Speed Control ◽  
System Structure ◽  
Direct Drive ◽  
Test Standards ◽  
Speed Controller ◽  
Fuzzy Neural ◽  
Vehicle Test

To solve the shortcomings of existing control methods for an electromagnetic direct drive vehicle robot driver, including large speed tracking error and large mileage deviation, a new adaptive speed control method for the electromagnetic direct drive vehicle robot driver based on fuzzy logic is proposed in this paper. The electromagnetic direct drive vehicle robot driver adapts an electromagnetic linear motor as its drive mechanism. The control system structure is designed. The coordinated controller for multiple manipulators is presented. Moreover, an adaptive speed controller for the electromagnetic direct drive vehicle robot driver is proposed to achieve the accurate tracking of desired speed. Experiments are conducted using a Ford FOCUS car. Performances of the proposed method, proportional–integral–derivative, and fuzzy neural network are compared and analyzed. Experimental results demonstrate that the proposed control method can accurately track the target speed, and it can inhabit the change of speed caused by interference under different test conditions, and it has small mileage deviation, which can meet the requirements of national vehicle test standards.

scholarly journals Formation Control of Unmanned Vessels with Saturation Constraint and Extended State Observation

2021 ◽  
Vol 9 (7) ◽  
pp. 772
Author(s):  
Huixuan Fu ◽  
Shichuan Wang ◽  
Yan Ji ◽  
Yuchao Wang
Keyword(s):  
Formation Control ◽  
Control Method ◽  
Tracking Error ◽  
External Environment ◽  
Control Force ◽  
Extended State ◽  
Parameter Perturbation ◽  
State Observation ◽  
Saturation Constraint ◽  
The Stability

This paper addressed the formation control problem of surface unmanned vessels with model uncertainty, parameter perturbation, and unknown environmental disturbances. A formation control method based on the control force saturation constraint and the extended state observer (ESO) was proposed. Compared with the control methods which only consider the disturbances from external environment, the method proposed in this paper took model uncertainties, parameter perturbation, and external environment disturbances as the compound disturbances, and the ESO was used to estimate and compensate for the disturbances, which improved the anti-disturbance performance of the controller. The formation controller was designed with the virtual leader strategy, and backstepping technique was designed with saturation constraint (SC) function to avoid the lack of force of the actuator. The stability of the closed-loop system was analyzed with the Lyapunov method, and it was proved that the whole system is uniformly and ultimately bounded. The tracking error can converge to arbitrarily small by choosing reasonable controller parameters. The comparison and analysis of simulation experiments showed that the controller designed in this paper had strong anti-disturbance and anti-saturation performance to the compound disturbances of vessels and can effectively complete the formation control.

Decoupling Control for Bearingless Synchronous Reluctance Motor Based on Neural Networks Inverse

2012 ◽  
Vol 150 ◽  
pp. 30-35
Author(s):  
Ze Bin Yang ◽  
Huang Qiu Zhu ◽  
Xiao Dong Sun ◽  
Tao Zhang
Keyword(s):  
Neural Networks ◽  
Control Method ◽  
Decoupling Control ◽  
Performance Simulation ◽  
Inverse Control ◽  
Linear Control Theory ◽  
Synchronous Reluctance Motor ◽  
Reluctance Motor ◽  
Static Performance ◽  
Simulation And Experiment

A novel decoupling control method based on neural networks inverse system is presented in this paper for a bearingless synchronous reluctance motor (BSRM) possessing the characteristics of multi-input-multi-output, nonlinearity, and strong coupling. The dynamic mathematical models are built, which are verified to be invertible. A controller based on neural network inverse is designed, which decouples the original nonlinear system to two linear position subsystems and an angular velocity subsystem. Furthermore, the linear control theory is applied to closed-loop synthesis to meet the desired performance. Simulation and experiment results show that the presented neural networks inverse control strategy can realize the dynamic decoupling of BSRM, and that the control system has fine dynamic and static performance.

The Simulation Analysis of Semi-Active Suspension System in Vehicle Based on Sliding Mode Control with Varying Structure

2011 ◽  
Vol 216 ◽  
pp. 96-100
Author(s):  
Jing Jun Zhang ◽  
Wei Sha Han ◽  
Li Ya Cao ◽  
Rui Zhen Gao
Keyword(s):  
Control Method ◽  
Simulation Analysis ◽  
Reference Model ◽  
Sliding Mode ◽  
Tracking Error ◽  
Active Suspension ◽  
Suspension System ◽  
Sliding Mode Controller ◽  
Error Dynamics ◽  
Dynamic Quality

A sliding mode controller for semi-active suspension system of a quarter car is designed with sliding model varying structure control method. This controller chooses Skyhook as a reference model, and to force the tracking error dynamics between the reference model and the plant in an asymptotically stable sliding mode. An equal near rate is used to improve the dynamic quality of sliding mode motion. Simulation result shows that the stability of performance of the sliding-mode controller can effectively improve the driving smoothness and safety.

The Implementation of Permanent Magnet Synchronous Motor Direct Torque Control

2013 ◽  
Vol 712-715 ◽  
pp. 2757-2760
Author(s):  
Jun Li Zhang ◽  
Yu Ren Li ◽  
Long Fei Fu ◽  
Fan Gao
Keyword(s):  
Coordinate System ◽  
Permanent Magnet ◽  
Control Method ◽  
Block Diagram ◽  
Permanent Magnet Synchronous Motor ◽  
Direct Torque Control ◽  
Torque Ripple ◽  
Synchronous Motor ◽  
Torque Control ◽  
Two Phase

In order to deeply understand the characteristics of the permanent magnet synchronous motor direct torque control method, its mathematical models were established in the two-phase stationary coordinate system, the two-phase synchronous rotating coordinate system, and x-y stator synchronous rotating coordinate system. The implementation process of direct torque control method in varied stator winding connection was analyzed in detail. In order to improve the speed and torque performance of the permanent magnet synchronous motor, the direct torque control block diagram and the space voltage vector selection table were given. Finally, the summary and outlook of reducing torque ripple in the permanent magnet synchronous motor direct torque control methods.

scholarly journals Finite-Time Switching Control of Nonholonomic Mobile Robots for Moving Target Tracking Based on Polar Coordinates

Complexity ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
Hua Chen ◽  
Shen Xu ◽  
Lulu Chu ◽  
Fei Tong ◽  
Lei Chen
Keyword(s):  
Mobile Robots ◽  
Finite Time ◽  
Control Method ◽  
Tracking Error ◽  
Switching Control ◽  
Polar Coordinates ◽  
Control Law ◽  
Moving Target ◽  
Nonholonomic Mobile Robots ◽  
Time Switching

In this paper, finite-time tracking problem of nonholonomic mobile robots for a moving target is considered. First of all, polar coordinates are used to characterize the distance and azimuth between the moving target and the robot. Then, based on the distance and azimuth transported from the sensor installed on the robot, a finite-time tracking control law is designed for the nonholonomic mobile robot by the switching control method. Rigorous proof shows that the tracking error converges to zero in a finite time. Numerical simulation demonstrates the effectiveness of the proposed control method.

DUTY-CYCLED SPINNING BASED 3D MOTION CONTROL APPROACH FOR BEVEL-TIPPED FLEXIBLE NEEDLE INSERTION

2018 ◽  
Vol 18 (07) ◽  
pp. 1840017 ◽  
Author(s):  
QIN YAO ◽  
XUMING ZHANG
Keyword(s):  
Motion Control ◽  
Control Method ◽  
Tracking Error ◽  
Open Loop ◽  
Loop Control ◽  
3D Motion ◽  
Control Approach ◽  
Target Error ◽  
The Mean ◽  
Simulation Results

Flexible needle has been widely used in the therapy delivery because it can advance along the curved lines to avoid the obstacles like important organs and bones. However, most control algorithms for the flexible needle are still limited to address its motion along a set of arcs in the two-dimensional (2D) plane. To resolve this problem, this paper has proposed an improved duty-cycled spinning based three-dimensional (3D) motion control approach to ensure that the beveled-tip flexible needle can track a desired trajectory to reach the target within the tissue. Compared with the existing open-loop duty-cycled spinning method which is limited to tracking 2D trajectory comprised of few arcs, the proposed closed-loop control method can be used for tracking any 3D trajectory comprised of numerous arcs. Distinctively, the proposed method is independent of the tissue parameters and robust to such disturbances as tissue deformation. In the trajectory tracking simulation, the designed controller is tested on the helical trajectory, the trajectory generated by rapidly-exploring random tree (RRT) algorithm and the helical trajectory. The simulation results show that the mean tracking error and the target error are less than 0.02[Formula: see text]mm for the former two kinds of trajectories. In the case of tracking the helical trajectory, the mean tracking error target error is less than 0.5[Formula: see text]mm and 1.5[Formula: see text]mm, respectively. The simulation results prove the effectiveness of the proposed method.

scholarly journals A model reference adaptive variable impedance control method for robot

2021 ◽  
Vol 336 ◽  
pp. 03005
Author(s):  
Xinchao Sun ◽  
Lianyu Zhao ◽  
Zhenzhong Liu
Keyword(s):  
Real Time ◽  
Tracking Control ◽  
Control Method ◽  
Impedance Control ◽  
Tracking Error ◽  
Reference Trajectory ◽  
Control Parameters ◽  
Model Reference ◽  
Force Tracking ◽  
Model Reference Adaptive

As a simple and effective force tracking control method, impedance control is widely used in robot contact operations. The internal control parameters of traditional impedance control are constant and cannot be corrected in real time, which will lead to instability of control system or large force tracking error. Therefore, it is difficult to be applied to the occasions requiring higher force accuracy, such as robotic medical surgery, robotic space operation and so on. To solve this problem, this paper proposes a model reference adaptive variable impedance control method, which can realize force tracking control by adjusting internal impedance control parameters in real time and generating a reference trajectory at the same time. The simulation experiment proves that compared with the traditional impedance control method, this method has faster force tracking speed and smaller force tracking error. It is a better force tracking control method.

scholarly journals Design of Supervisory Control for Speed Control of Wind Turbine using Torque-Control Method Based on Buck Converter

2020 ◽  
Vol 190 ◽  
pp. 00019
Author(s):  
Katherin Indriawati ◽  
Choirul Mufit ◽  
Andi Rahmadiansah
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Supervisory Control ◽  
Control Method ◽  
Speed Control ◽  
Buck Converter ◽  
Torque Control ◽  
Control Mode ◽  
Rotor Speed ◽  
Integral Control

The variation of wind speed causes the electric power generated by the turbine also varies. To obtain maximum power, the rotor speed of wind turbines must be optimally rated. The rotor speed can be controlled by manipulating the torque from the generator; this method is called Torque Control. In that case, a DC-DC converter is needed as the control actuator. In this study, a buck converter-based supervisory control design was performed on the Horizontal-axis wind turbines (HAWT). Supervisory control is composed of two control loops arranged in cascade, and there is a formula algorithm as the supervisory level. The primary loop uses proportional control mode with a proportional gain of 0.3, whereas in the secondary loop using proportional-integral control mode with a proportional gain of 5.2 and an integral gain of 0.1. The Supervisory control has been implemented successfully and resulted in an average increase in turbine power of 4.1 % at 5 m s–1 and 10.58 % at 6 m s–1 and 11.65 % at 7 m s–1, compared to wind turbine systems without speed control.

Sign in / Sign up

Export Citation Format

Share Document