scholarly journals Effect of Coarse Content on Compaction Test

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
Badee Alshameri
Keyword(s):  
Specific Gravity ◽  
Moisture Content ◽  
Linear Relationship ◽  
Bulk Density ◽  
Optimum Moisture Content ◽  
Coefficient Of Determination ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Soil Densification ◽  
The Relationship

The compaction is a mechanism to densify the loose soils. The maximum soil densification can be achieved by optimization of the desirable optimum moisture content (OMC) and maximum dry density (MDD). The maximum dry density and the optimum moisture content were affected by several parameters. The coarse content (CC) is one of these parameters. This paper studied the effect of the coarse content on the compaction parameters (MDD, OMC). Several sand-kaolin mixtures had coarse content ranged from 30 % to 80 % and moisture content ranged from 12% to 20% were used to inspect the relationship between CC, specific gravity (Gs), MDD, OMC, and bulk density. The results presented five empirical correlations with coefficient of determination (R2 ≥ 0.98) between CC, Gs, MDD, OMC and bulk density. The comparison between the current study and previous researchers indicated that both soil type and moisture content have significant effect on the efficiency of the empirical correlation equations between the maximum dry density, specific gravity, and coarse content. The results indicated a linear relationship between coarse content toward maximum dry density and specific gravity where both MDD and Gs increased with an increase CC. In contrary, the results showed non-linear relationship between optimum moisture content and coarse content where OMC decrease with an increase CC.

scholarly journals Evaluation of Bentonite Mixed Indigenous Clays for Development of Clay Liners

2020 ◽  
Vol 6 ◽  
pp. 24-32
Author(s):  
Muhammad Israil ◽  
Muhammad Ashraf ◽  
Muhammad Fahim ◽  
Rashid Rehan ◽  
Sajjad Wali Khan ◽  
...  
Keyword(s):  
Hydraulic Conductivity ◽  
Specific Gravity ◽  
Moisture Content ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Atterberg Limits ◽  
Dry Density ◽  
Clay Liners ◽  
Maximum Dry Density ◽  
Free Swell

This study presents experimental investigation of indigenous clays mixed with Bentonite to assess their suitability in potential use as clay liners. Soil samples with 0, 4, 8, and 12% Bentonite content from three different sites in Peshawar region were tested for various geotechnical properties. Grain size distribution, specific gravity, Atterberg limits and free swell were found through laboratory tests using appropriate ASTM procedures. Maximum dry density and optimum moisture content were calculated using Atterberg limits in available relationships. Finally, one dimensional consolidation tests were conducted to find relevant parameters for calculating hydraulic conductivity. A decrease in specific gravity, increase in free swell, and in optimum moisture content, decline in maximum dry density and hydraulic conductivity was observed with increase in Bentonite content across all three soil samples. During free swell, the soil clusters become larger leading to formation of floccules resulting in the narrowing of inter-particle space and thus blocking of permeable paths. It is concluded that 8% Bentonite content by weight yields a suitable mixture for a clay liner that has hydraulic conductivity in the range of recommended limits.

scholarly journals An analysis of the factors influencing the relationship between soil properties and optimum moisture content and the formulation of an abbreviated test method of determinig maximum dry density

1997 ◽  
Author(s):  
◽  
Anthony James Allinsin
Keyword(s):  
Moisture Content ◽  
Liquid Limit ◽  
Optimum Moisture Content ◽  
Test Method ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Strength And Durability ◽  
The Relationship ◽  
Standard Compaction

The strength and durability of any soil structure is dependent on the quality of the compaction of the soil. This quality is measured by employing a standard compaction test, which provides a standard with which density may be compared, called the maximum dry density, and the moisture content of the soil at which this is achieved, called the optimum moisture content. As a matter of routine during quality control, the particle size distribution, plasticity index and liquid limit of the soil are determined at the same time as its maximum dry density and optimum moisture content.

scholarly journals Effect of Sand Percentage on the Compaction Properties and Undrained Shear Strength of Low Plasticity Clay

2021 ◽  
Vol 9 (1) ◽  
pp. 16-20
Author(s):  
Iyad Alkroosh ◽  
Ali Al-Robay ◽  
Prabir Sarker ◽  
Saif Alzabeebee
Keyword(s):  
Shear Strength ◽  
Moisture Content ◽  
Undrained Shear Strength ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Sand Content ◽  
Compression Tests ◽  
Maximum Dry Density ◽  
Sand Mixture ◽  
Undrained Shear

This paper investigates the influence of sand content on the mechanical behavior of a low plasticity clay that collected from south of Iraq (Sumer town). Samples have been prepared with sand contents of 0%, 10%, 20%, 30%, and 40% of the clay weight. Standard Proctor and unconfined compression tests have been carried out and the optimum moisture content, maximum dry density, and undrained shear strength have been determined. The results show a gradual increasing trend of the maximum dry density with the increase of the sand content up to 30%. The highest dry density reaches 1.90 g/cm3 corresponding to an optimum moisture content of 12%. In addition, this paper shows that the undrained shear strength is inversely proportional to the increase of the percentage of sand. The results of this work provide a useful addition to the literature regarding the behaviour or low plasticity clay-sand mixture.

Compaction Characteristic of Lime Modified Expansive Soil

2013 ◽  
Vol 710 ◽  
pp. 348-351
Author(s):  
Zheng Rong Zhao ◽  
Lei Wang ◽  
Hong Xia Yang
Keyword(s):  
Moisture Content ◽  
Expansive Soil ◽  
Size Composition ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Content Increase ◽  
Maximum Dry Density ◽  
Compaction Curve ◽  
Compaction Characteristic ◽  
Two Peaks

Through compaction test discussed about the compaction characteristics of expansive soil by lime modified in middle of Shandong province. The results show that the optimum moisture content is lower when the expansive soil is cured by dry compaction method, and the maximum dry density is higher. Compaction curve appeared the phenomenon of two peaks when expansive soil is cured by wet compaction method.Lime content of lime improved expansive soil, particle size composition, age and compaction function have influence on compaction curve.With the increase of the quantity of lime, the optimum moisture content increases, the maximum dry density decreases. With the age growth, the optimum moisture content increase slightly,the maximum dry density decreases slightly. The bigger the compaction work, the smaller moisture content is, the larger the maximum dry density is.

scholarly journals Engineering behaviour of stabilized laterite and kaolin using lignin

2018 ◽  
Vol 250 ◽  
pp. 01008
Author(s):  
Tuan Noor Hasanah Tuan Ismail ◽  
Siti Aimi Nadia Mohd Yusoff ◽  
Ismail Bakar ◽  
Devapriya Chitral Wijeyesekera ◽  
Adnan Zainorabidin ◽  
...  
Keyword(s):  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Laboratory Tests ◽  
Dry Weight ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Dry Density ◽  
Laterite Soil ◽  
Maximum Dry Density ◽  
Steady Rate

Soils at many sites do not always have enough strength to bear the structures constructed over them and some of the soil may need to be stabilized in order to improve their geotechnical properties. In this paper, routine laboratory tests were critically carried out to investigate the efficacy of lignin in improving the strength behaviour of the soils. Two different soil samples (laterite and kaolin) were studied and mixed with different proportions of lignin (2% and 5% of dry weight of soil), respectively. Unconfined Compressive Strength (UCS) characteristics evaluated in this study were done on samples at their maximum dry density and optimum moisture content (obtained from compaction tests). The UCS tests on all the specimens were carried out after 0, 7, 15, 21 and 30 days of controlled curing. The research results showed that the addition of lignin into kaolin reduced its maximum dry density while giving progressively higher optimum moisture content. Contrarily, with the laterite soil, both maximum dry density and optimum moisture content simultaneously increased when lignin was added into the soils. The UCS results showed that the the stabilized laterite with 2% lignin continued to gain strength significantly at a fairly steady rate after 7 days. Unfortunately, lignin did not show a significant effect in kaolin.

scholarly journals COMPACTION ASSESSMENT OF RECYCLED AGGREGATES FOR USE IN UNBOUND SUBBASE APPLICATION

2014 ◽  
Vol 20 (2) ◽  
pp. 169-174 ◽  
Author(s):  
Vahid Ayan ◽  
Mukesh C. Limbachiya ◽  
Joshua R. Omer ◽  
Seyyed Masoud Nasr Azadani
Keyword(s):  
Moisture Content ◽  
Asphalt Pavement ◽  
Optimum Moisture Content ◽  
Recycled Concrete ◽  
Recycled Aggregates ◽  
Dry Density ◽  
Reclaimed Asphalt Pavement ◽  
Maximum Dry Density ◽  
Reclaimed Asphalt ◽  
Natural Aggregates

Study was recently conducted at Kingston University to assess the suitability of using recycled concrete aggregate (RCA) and reclaimed asphalt pavement (RAP) in unbound subbase mixtures. The results showed that the use of 100% recycled aggregates increased the optimum moisture content and decreased the maximum dry density of the sub-base materials in comparison with natural aggregates. Moreover, the replacement of RCA by reclaimed asphalt pavement by 50% decreased the optimum moisture content and increased the maximum dry density in proportion to 100% RCA. The effects of physical properties on 0% air void and compaction curve were discussed for each type of subbase. The CBR values of the subbase materials prepared with 100%RCA is lower than subbase mixture with 100% natural aggregates. The CBR further decreased for replaced subbase with RAP so that 50%RCA + 50%RAP is not suitable for unbound subbase from the point of CBR view. In each mix the trend of CBR value was investigated in terms of water content. This research found some significant practical points to use in site works.

Analysis for Influence Factors of Cold Recycling Mixture Compaction Test

2012 ◽  
Vol 204-208 ◽  
pp. 1633-1637
Author(s):  
Yong Bing Wang ◽  
Guo Qiang Ying ◽  
Jian Lin Hu ◽  
Hua Wei Wei ◽  
Qian Zhang
Keyword(s):  
Moisture Content ◽  
Water Absorption ◽  
Base Material ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Surface Material ◽  
Test Results ◽  
Maximum Dry Density ◽  
Compaction Test ◽  
Recycled Material

In order to study the factors which influence the inorganic binder stabilized material’s compaction test results, different recycled material content therefore different reclaimed gradation mixtures are tested while varying the amount of cement. The experiment results show that contents of the recycled base material and the recycled surface material on the compaction test results are determined by the change of their density and water absorption ratio. Dry density of the recycled mixture increases with the increase of the reclaimed base material density. Low water absorption ratio of the recycled material reduces the reclaimed mixture’s optimum moisture content. Density of the reclaimed wearing surface material reduces the maximum dry density of the reclaimed mixture because the old wearing surface material has lower density. Its low water absorption reduces the optimum moisture content of the recycled mixture. Influence of cement content on compaction test results is the increase of the cement content can enhance the maximum dry density and optimum moisture content of the recycled material. Through the analysis of the results of the compaction test, the key factors in the recycled material compaction test are unveiled.

Study of Key Parameters in the Process of Aeolian Sand Compactibility

2014 ◽  
Vol 580-583 ◽  
pp. 278-282
Author(s):  
Ying Zi Yin ◽  
Ya Lei Wang
Keyword(s):  
Moisture Content ◽  
Inner Mongolia ◽  
Retaining Wall ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Aeolian Sand ◽  
Maximum Dry Density ◽  
Factors Affecting ◽  
Practical Engineering ◽  
Vibration Impact

The main factors affecting soil compatibility include moisture content, compaction work, soil type, grading and coarse material content etc.. The effects of compaction work are as follows: the stronger compaction work is, the more larger soil dry density is. The optimum moisture content decreases with the compaction work increasing. This paper mainly studies the effect of compaction work to aeolian sand compatibility. Its lay-down thickness is about 30-50cm when we use vibratory roller to compact aeolian sand in practical engineering. This paper analysis’s and studies the maximum dry density and the optimum moisture content of aeolian sand in the middle region of Inner Mongolia, and achieves its lay-down thicknesses are 30cm,40cm,and 50cm respectively at the optimum moisture content. We use 85kg vibration-impact rammer instead of YZ 18 vibratory roller to simulate the aeolian sand compaction effect at the optimum moisture content. The specification does not specify the number of compatibility times, but it is generally 3 to 5 times in the actual project .We choose the most suitable compatibility times and lay-down thickness through anglicizing the Aeolian sand compactness for vibration-impact rammer rolling on eloign sand 3 times,4 times, and 5 times respectively at 3 different kinds of lay-down thicknesses. Through the study of the Inner Mongolia area Aeolian sand, it provides a useful reference for highway and railway construction in the desert area as well as the encapsulated layer thickness of reinforced retaining wall, a new type support structure.

scholarly journals Pengaruh Penggunaan Pasir Putih Sebagai Bahan Tambah Untuk Stabilisasi Tanah Desa Bangkuang Kabupaten Barito Selatan

2019 ◽  
Vol 3 (2) ◽  
pp. 1-7
Author(s):  
Syahdi Syahdi ◽  
Muhammad Suhaimi
Keyword(s):  
Moisture Content ◽  
Soil Properties ◽  
Liquid Limit ◽  
Optimum Moisture Content ◽  
Plasticity Index ◽  
Dry Density ◽  
Maximum Dry Density ◽  
White Sand ◽  
Research Activities ◽  
The Many

Tanah merupakan salah satu dari sekian banyak material yang bervariasi (heterogen) antara satu lokasi dengan lokasi yang lain., maka dalam penelitian ini melakukan penambahan material pasir putih yang kemudian dicampurkan dengan tanah asli yang berasal dari desa Bangkuang Kecapamatan Karau Kuala Kabupaten Barito selatan. Kegiatan penelitian dilakukan di laboratorium Geoteknik dan Transportasi Politeknik Negeri Banjarmasin meliputi beberapa metode pungujian dilakukan sesuai dengan standar penelitian yaitu: SNI 03-1965-2008, SNI 03-1964-2008, SNI 03-1967-2008, SNI 03-1965-2008,SNI 03-1743-2008 SNI 03-1738-2011, dan SNI 2828:2011.  Hasil penelitian, dengan penambahan pasir putih sangat berpengaruh terhadap perbaikan sifat – sifat tanah yang akan digunakan untuk bahan stabilisasi subgredre,   maka didapat nilai sifat-sifat tanah diberi bahan pasir putih (0%) meliputi; kadar air (W) 23,87%, berat jenis (Gs) 2,59, batas cair (LL) 33,9%, batas plastis (PL) 20,11%, plastisitas indeks (PI) 13,79%, kadar air optimum (OMC) 18,6%, kepadatan kering maksimum (dMax) 1,61 Gr/Cm3 dan CBR desain 5%. Nilai sifat-sifat tanah diberi bahan tambah pasir putih. Nilai sifat-sifat tanah diberi bahan tambah pasir putih (15%) meliputi; berat jenis gabungan (Gs) 2,62, batas cair (LL) 29,6%, batas plastis (PL) 19,52%, plastisitas indeks (PI) 10,08%, kadar air optimum (Omc) 81,5%, kepadatan kering maksimum (dMax)) 1,54 Gr/Cm3 dan CBR desain 6,1%, berat isi kering (d) 1,538 gr/cm³. Abstract Land is one of the many varied material (heterogeneous) between one site and another location., then in this research performs addition material of white sand is then blended with the native soil that comes from the village of Karau Kuala Kecapamatan District Bangkuang Barito South. Research activities carried out in the laboratory of Geotechnical and transportation State Polytechnic Banjarmasin includes several methods of pungujian conducted in accordance with the standards of research, namely: in accordance with the SNI 03-1965-2008, SNI 03-1964-2008, SNI 03-1967-2008, SNI 03-1965-2008, SNI 03-1743-2008, SNI 03-1738-2011, and SNI 2828:2011. Results of the study, with the addition of white sand is very influential towards the improvement of the nature – nature of the land to be used for subgredre stabilization materials, then obtained the value soil properties are given materials white sand (0%) include; moisture content (W) 23.87%, heavy types (Gs) 2.59, liquid limit (LL) 33.9%, limits plastis (PL) 20.11%, plasticity index (PI) 13.79%, optimum moisture content (OMC) 18.6%, maximum dry density (/dMax) 1.61 Gr/Cm3 and CBR design 5%. The value soil properties are given the added ingredient of white sand. The value soil properties are given the added ingredient of white sand (15%) include; the weight of the combined type (Gs) 2.62, liquid limit (LL) 29.6%, limits plastis (PL) 19.52%, plasticity index (PI) 10.08%, optimum moisture content (Omc) 81.5%, maximum dry density (/dMax)) 1.54 Gr/Cm3 and CBR design 6.1%, weight dry (/d) 1.538 gr/cm ³.

Sign in / Sign up

Export Citation Format

Share Document