scholarly journals Numerical Studies on Temperature and Material Flow During Friction Stir Welding using Different Tool Pin Profiles

2021 ◽  
Vol 83 (1) ◽  
pp. 91-104
Author(s):  
M. D. Bindu ◽  
P. S. Tide ◽  
A. B. Bhasi
Keyword(s):  
Friction Stir Welding ◽  
Temperature Distribution ◽  
Material Flow ◽  
Three Dimensional ◽  
Friction Stir ◽  
Specific Strength ◽  
Numerical Studies ◽  
Computational Fluid Dynamics Cfd ◽  
Tool Pin ◽  
Metal Hardness

A three dimensional computational fluid dynamics (CFD) model has been developed to study the effect of tool pin profile on the material flow and temperature development in friction stir welding (FSW) of high specific strength AA 7068 alloy. Numerical simulations were carried out using a RNG k-e turbulence model. Three tool pin profiles, viz. cylindrical, conical and straight cylindrical threaded were considered for the simulation. The temperature distribution and material flow pattern obtained from the simulation were compared for different pin profiles. Simulation results predicted Temperature distribution and material maxing was better in straight cylindrical tapered thread pin welds. Weld joints were fabricated using the straight cylindrical threaded pin with the same parametric combinations as in the simulation. Peak temperature measured in the experiment was less than that obtained by simulation. Hardness measurements taken at different weld regions has showed that about 71% of that of the base metal hardness is obtained with the threaded tool pin. The microstructure study revealed a defect free weld joint. Precipitates distributed in the microstructure indicate sufficient heat input to join the material without dissolving precipitates. The developed numerical model is helpful in optimising FSW process parameters.

scholarly journals Analysis of the tool plunge in friction stir welding - comparison of aluminium alloys 2024 T3 and 2024 T351

2016 ◽  
Vol 20 (1) ◽  
pp. 247-254
Author(s):  
Darko Veljic ◽  
Bojan Medjo ◽  
Marko Rakin ◽  
Zoran Radosavljevic ◽  
Nikola Bajic
Keyword(s):  
Friction Stir Welding ◽  
Plastic Strain ◽  
Heat Generation ◽  
Aluminium Alloys ◽  
Three Dimensional ◽  
Equivalent Plastic Strain ◽  
Fe Model ◽  
Arbitrary Lagrangian Eulerian ◽  
Friction Stir ◽  
Tool Pin

Temperature, plastic strain and heat generation during the plunge stage of the friction stir welding (FSW) of high-strength aluminium alloys 2024 T3 and 2024 T351 are considered in this work. The plunging of the tool into the material is done at different rotating speeds. A three-dimensional finite element (FE) model for thermomechanical simulation is developed. It is based on arbitrary Lagrangian-Eulerian formulation, and Johnson-Cook material law is used for modelling of material behaviour. From comparison of the numerical results for alloys 2024 T3 and 2024 T351, it can be seen that the former has more intensive heat generation from the plastic deformation, due to its higher strength. Friction heat generation is only slightly different for the two alloys. Therefore, temperatures in the working plate are higher in the alloy 2024 T3 for the same parameters of the plunge stage. Equivalent plastic strain is higher for 2024 T351 alloy, and the highest values are determined under the tool shoulder and around the tool pin. For the alloy 2024 T3, equivalent plastic strain is the highest in the influence zone of the tool pin.

Control of Material Flow During Friction Stir Welding Between Aluminum and Steel by Welding Tool Shape

2020 ◽  
Author(s):  
Toshiaki Yasui ◽  
Yuki Ogura ◽  
Xu Huilin ◽  
F. Farrah Najwa ◽  
Daichi Sugimoto ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Material Flow ◽  
Simulation Experiment ◽  
Low Cost ◽  
Flow Analysis ◽  
Material Flow Analysis ◽  
High Strength ◽  
Friction Stir ◽  
Tool Shape ◽  
Computational Fluid Dynamics Cfd

Abstract For the Friction stir welding (FSW) between aluminum and steel is important to fabricate vehicles with light weight and high strength for safety at low cost. For the fabrication of sound weld, it is necessary to control the material flow during FSW. In this study, the material flow during FSW was elucidated by numerical simulation by computational fluid dynamics (CFD) analysis and simulation experiment by transparent Poly-vinyle chloride (PVC) as simulant of aluminum and tracer material. Based on this material flow analysis, several shapes of welding tool were examined for control of material flow during FSW. Scroll shoulder is effective for enhancement of stirring zone by increasing material velocity around the probe. Flute and fine screw probe promote the material flow in depth and horizontal direction. The welding tool with scroll shoulder and flute and fine screw probe achieved sound weld with highest tensile strength of 120.4 MPa.

Numerical Study of the Tool Rake Angle Effect on the Material Flow in Friction Stir Welding Process

2007 ◽  
Author(s):  
Hosein Atharifar ◽  
Radovan Kovacevic
Keyword(s):  
Friction Stir Welding ◽  
Material Flow ◽  
Numerical Study ◽  
Welding Process ◽  
Rake Angle ◽  
Heat Transfer Analysis ◽  
Tool Geometry ◽  
Friction Stir ◽  
Tool Pin ◽  
Welding Processes

Minimizing consumed energy in friction stir welding (FSW) is one of the prominent considerations in the process development. Modifications of the FSW tool geometry might be categorized as the initial attempt to achieve a minimum FSW effort. Advanced tool pin and shoulder features as well as a low-conductive backing plate, high-conductive FSW tools equipped with cooling fins, and single or multi-step welding processes are all carried out to achieve a flawless weld with reduced welding effort. The outcomes of these attempts are considerable, primarily when the tool pin traditional designs are replaced with threaded, Trifiute or Trivex geometries. Nevertheless, the problem remains as to how an inclined tool affects the material flow characteristics and the loads applied to the tool. It is experimentally proven that a positive rake angle facilitates the traverse motion of the FSW tool; however, few computational evidences were provided. In this study, numerical material flow and heat transfer analysis are carried out for the presumed tool rake angle ranging from −4° to 4°. Afterwards, the effects of the tool rake angle to the dynamic pressure distribution, strain-rates, and velocity profiles are numerically computed. Furthermore, coefficients of drag, lift, and side force and moment applied to the tool from the visco-plastic material region are computed for each of the tool rake angles. Eventually, this paper confirms that the rake angle dramatically affects the magnitude of the loads applied to the FSW tool, and the developed advanced numerical model might be used to find optimum tool rake angle for other aluminum alloys.

scholarly journals The Effect of Tool Pin Size and Taper Angle on the Thermal Process and Plastic Material Flow in Friction Stir Welding

2021 ◽  
Author(s):  
Jie Chen ◽  
Lei Shi ◽  
Chuansong Wu ◽  
Yuanning Jiang
Keyword(s):  
Friction Stir Welding ◽  
Shear Layer ◽  
Layer Thickness ◽  
Material Flow ◽  
Horizontal Plane ◽  
Thermal Process ◽  
Plastic Material ◽  
Taper Angle ◽  
Friction Stir ◽  
Tool Pin

Abstract Friction stir welding (FSW) tool pin, as a critical component of FSW tool, plays an important role in determining the final joint properties by affecting the heat generation, plastic material flow, welding loads and so on. However, the influence of tool pin on heat and mass transfer in FSW are not elucidated. In the present study, a validated model was adopted to quantitatively analyze the effects of pin size and taper angle on the thermal process and plastic material flow in FSW. It reveals that the torque and transverse force imposed on the pin are increased with the increase of the pin diameters (including its root diameter, its tip diameter and its size in condition of constant taper angle), while the total tool torque various a little for the tool pin diameter considered in this study. When the pin diameters increase, the viscosity of the materials near the pin is decreased, while the temperature as well as the flow velocity is increased. More plastic material near the tool could rotate around the tool with an increase of the pin diameter. The TMAZ boundary is enlarged with larger pin diameters in FSW. Particularly, the shear layer thickness of the same horizontal plane in the range of 1 mm < z < 5 mm is significantly enlarged with an increase of pin root diameters. However, the shear layer thickness of the same horizontal plane in the region of z < 5 mm is increased when using a larger pin tip diameter. In addition, maximum width of TMAZ boundary at the top surface of workpiece was not affected by pin diameters. The model is validated by experimental results. It lays solid foundation for optimizing the tool pin size and taper angle in FSW.

scholarly journals Numerical Simulation of Material Flow and Analysis of Welding Characteristics in Friction Stir Welding Process

Metals ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 621 ◽  
Author(s):  
Haitao Luo ◽  
Tingke Wu ◽  
Peng Wang ◽  
Fengqun Zhao ◽  
Haonan Wang ◽  
...  
Keyword(s):  
Finite Element ◽  
Friction Stir Welding ◽  
Finite Element Model ◽  
Material Flow ◽  
Welding Process ◽  
Element Model ◽  
Welding Seam ◽  
Friction Stir ◽  
Tool Pin ◽  
The Finite Element Model

Friction stir welding (FSW) material flow has an important influence on weld formation. The finite element model of the FSW process was established. The axial force and the spindle torque of the welding process were collected through experiments. The feasibility of the finite element model was verified by a data comparison. The temperature field of the welding process was analyzed hierarchically. It was found that the temperature on the advancing side is about 20 °C higher than that on the retreating side near the welding seam, but that the temperature difference between the two sides of the middle and lower layers was decreased. The particle tracking technique was used to study the material flow law in different areas of the weld seam. The results showed that part of the material inside the tool pin was squeezed to the bottom of the workpiece. The material on the upper surface tends to move downward under the influence of the shoulder extrusion, while the material on the lower part moves spirally upward under the influence of the tool pin. The material flow amount of the advancing side is higher than that of the retreating side. The law of material flow reveals the possible causes of the welding defects. It was found that the abnormal flow of materials at a low rotation speed and high welding speed is prone to holes and crack defects. The forming reasons and material flow differences in different regions are studied through the microstructure of the joint cross section. The feasibility of a finite element modeling and simulation analysis is further verified.

A thermal-plastic model of friction stir welding in aluminum alloy

2017 ◽  
Vol 24 (3) ◽  
pp. 439-446
Author(s):  
Zhang Peilei ◽  
Yan Hua ◽  
Li Chonggui ◽  
Yu Zhishui ◽  
Lu Qinghua
Keyword(s):  
Plastic Deformation ◽  
Friction Stir Welding ◽  
Three Dimensional ◽  
Transfer Model ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Moving Coordinate ◽  
Model Of Friction ◽  
Tool Pin ◽  
Good Agreement

AbstractA three-dimensional heat transfer model for friction stir welding is presented in this paper. A moving coordinate was introduced to reduce the difficulty of modeling the moving tool. Heat input from the tool shoulder and the tool pin were considered in the model. The plastic deformation heat was introduced into the model, too. It is clear that the heat production increased owing to plastic deformation, and this process depends on the stress level. Temperature measurement experiments were done to validate the calculated results. The calculated results were in good agreement with the experimental results. Preheating the workpiece is beneficial to obtain a good weld seam.

Three-Dimensional Visualization of Material Flow During Friction Stir Welding of Steel and Aluminum

2014 ◽  
Vol 23 (11) ◽  
pp. 4143-4147 ◽  
Author(s):  
Yoshiaki Morisada ◽  
Takuya Imaizumi ◽  
Hidetoshi Fujii ◽  
Muneo Matsushita ◽  
Rinsei Ikeda
Keyword(s):  
Friction Stir Welding ◽  
Material Flow ◽  
Three Dimensional ◽  
Friction Stir
Sign in / Sign up

Export Citation Format

Share Document