scholarly journals FRACTURE OF CONCRETE CONTAINING CRUMB RUBBER

2013 ◽  
Vol 19 (3) ◽  
pp. 447-455 ◽  
Author(s):  
Audrius Grinys ◽  
Henrikas Sivilevičius ◽  
Darius Pupeikis ◽  
Ernestas Ivanauskas
Keyword(s):  
Fracture Energy ◽  
Mouth Opening ◽  
Crumb Rubber ◽  
Crack Mouth Opening Displacement ◽  
Concrete Fracture ◽  
Opening Displacement ◽  
Polypropylene Fibres ◽  
Abrupt Decrease ◽  
Resistance To Stress ◽  
Maximum Stresses

Every year, colossal amounts of used and non-biodegradable rubber tyres are accumulated in the world. Experience shows that the most efficient way to increase the concrete fracture energy G F (N/m) is to use metal or polypropylene fibres. The optimal content of fibre increases concrete resistance to stress (especially tensile stress under bending force). Concrete fracture is not brittle; concrete continues deforming after maximum stresses and is able to resist certain stresses, there is no abrupt decrease in loading. The research has proved that crumb rubber can be used in concretes as an alternative to metal and polypropylene fibres. The investigation has found that rubber waste additives, through their specific properties can partly take up tensile stresses in concrete and make the concrete fracture more plastic; besides, such concrete requires a significantly higher fracture energy and concrete samples can withstand much higher residual strength at 500 µm crack mouth opening displacement (CMOD) and deflection.

scholarly journals Fracture Properties and Softening Curves of Steel Fiber-Reinforced Slag-Based Geopolymer Mortar and Concrete

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1445 ◽  
Author(s):  
Yao Ding ◽  
Yu-Lei Bai
Keyword(s):  
Fracture Toughness ◽  
Fracture Energy ◽  
Inverse Analysis ◽  
Steel Fiber ◽  
Mouth Opening ◽  
Crack Mouth Opening Displacement ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Opening Displacement ◽  
Fracture Properties

Adding short steel fibers into slag-based geopolymer mortar and concrete is an effective method to enhance their mechanical properties. The fracture properties of steel fiber-reinforced slag-based geopolymer concrete/mortar (SGC/SGM) and unreinforced control samples were compared through three-point bending (TPB) tests. The influences of steel fiber volume contents (1.0%, 1.5% and 2.0%) on the fracture properties of SGC and SGM were studied. Load-midspan deflection (P-δ) curves and load-crack mouth opening displacement (P-CMOD) curves of the tested beams were recorded. The compressive and splitting tensile strengths were also tested. The fracture energy, flexural strength parameters, and fracture toughness of steel fiber-reinforced SGC and SGM were calculated and analyzed. The softening curves of steel fiber-reinforced SGC and SGM were determined using inverse analysis. The experimental results show that the splitting tensile strength, fracture energy, and fracture toughness are significantly enhanced with fiber incorporation. A strong correlation between the equivalent and residual flexural strengths is also observed. In addition, the trilinear strain-softening curves obtained by inverse analysis predict well of the load-displacement curves recorded from TPB tests.

Comparison study of crack propagation in rubberized and conventional prestressed concrete sleepers using digital image correlation

2021 ◽  
pp. 095440972110205
Author(s):  
Guoqing Jing ◽  
Du yunchang ◽  
Ruilin You ◽  
Mohammad Siahkouhi
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Prestressed Concrete ◽  
Mouth Opening ◽  
Image Correlation ◽  
Crack Mouth Opening Displacement ◽  
Experimental Program ◽  
Pure Bending ◽  
Opening Displacement ◽  
Rubber Concrete

Rubber concrete (RC) has been confirmed to be suitable for concrete sleeper production. This paper studies the cracking behaviour of conventional and rubber-reinforced concrete sleepers based on the results of an experimental program. The cracking behaviour in the pure bending zone was analysed up to a load of 140 kN. The crack mouth opening displacement (CMOD) was accordingly measured using a digital image correlation (DIC) method. The DIC results show that the rubber prestressed concrete sleeper (RPCS) has a resistance against crack initiation that is 20% greater than that of the conventional prestressed concrete sleeper (CPCS) under the same loading condition; however, due to the higher crack growth rate of the RPCS, the first crack detected by the operator forms at 60 kN, which corresponds to a strength approximately 9% lower compared with the 65 kN load at which the first crack is detected in the CPCS. Before the first crack (60 kN), the RPCS has a deflection 35% lower than that of the CPCS, but after cracking, at loads of 80 kN, 100 kN and 140 kN, the RPCS has a deflection 15%, 4% and 24% higher than that of the CPCS, respectively.

Studies on effect of steel fiber and coarse aggregate on fracture properties of self compacting concrete using wedge splitting test

2019 ◽  
Vol 11 (6) ◽  
pp. 751-767
Author(s):  
Raja Rajeshwari B. ◽  
Sivakumar M.V.N.
Keyword(s):  
Fracture Energy ◽  
Coarse Aggregate ◽  
Peak Load ◽  
Mouth Opening ◽  
Test Method ◽  
Crack Mouth Opening Displacement ◽  
Fine Aggregate ◽  
Content Type ◽  
Fracture Properties ◽  
Splitting Test

Purpose Fracture properties depend on the type of material, method of testing and type of specimen. The purpose of this paper is to evaluate fracture properties by adopting a stable test method, i.e., wedge split test. Design/methodology/approach Coarse aggregate of three different sizes (20 mm, 16 mm and 12.5 mm), three ratios of coarse aggregate, fine aggregate (CA:FA) (50:50, 45:55, 40:60), presence of steel fibers, and specimens without and with guide notch were chosen as parameters of the study. Findings Load-crack mouth opening displacement curves indicate that for both fibrous and non-fibrous mixes, higher volume of aggregate and higher size of coarse aggregate have high fracture energy. Originality/value For all volumes of coarse aggregate, it was noticed that specimens with 12.5 mm aggregate size achieved highest peak load and abrupt drop post-peak. The decrease in coarseness of internal structure of concrete (λ) resulted in the increase of fracture energy.

Effects of Weld Strength Mismatch on Estimation Procedures for J and CTOD Fracture Parameters Using SE(B) Specimens

2007 ◽  
Author(s):  
Gustavo H. B. Donato ◽  
Claudio Ruggieri
Keyword(s):  
Mouth Opening ◽  
Estimation Procedure ◽  
Primary Objective ◽  
Weld Strength ◽  
Crack Mouth Opening Displacement ◽  
Opening Displacement ◽  
Fracture Parameters ◽  
Wide Range ◽  
Estimation Procedures ◽  
Fracture Specimens

This work presents an exploratory development of J and CTOD estimation procedures for welded fracture specimens under bending based upon plastic eta factors and plastic rotation factors. The techniques considered include: i) estimating J and CTOD from plastic work and ii) estimating CTOD from the plastic rotational factor. The primary objective is to gain additional understanding on the effect of weld strength mismatch on estimation techniques to determine J and CTOD fracture parameters for a wide range of a/W-ratios and mismatch levels. Very detailed non-linear finite element analyses for plane-strain models of SE(B) fracture specimens with center cracked, square groove welds provide the evolution of load with increased load-line displacement and crack mouth opening displacement which are required for the estimation procedure. The results show that levels of weld strength mismatch within the range ±20% mismatch do not affect significantly J and CTOD estimation expressions applicable to homogeneous materials, particularly for deeply cracked fracture specimens. The present analyses, when taken together with previous studies, provide a fairly extensive body of results which serve to determine parameters J and CTOD for different materials using bend specimens with varying geometries and mismatch levels.

Experimental analysis of crack evolution in concrete by the acoustic emission technique

2015 ◽  
Author(s):  
J. Saliba ◽  
A. Loukili ◽  
J.P. Regoin ◽  
D. Grégoire ◽  
L. Verdon ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Fracture Process ◽  
Process Zone ◽  
Mouth Opening ◽  
Acoustic Emissions ◽  
Plain Concrete ◽  
Crack Mouth Opening Displacement ◽  
Notch Depth ◽  
Opening Displacement ◽  
Magnitude Distribution

The fracture process zone (FPZ) was investigated on unnotched and notched beams with different notch depths. Three point bending tests were realized on plain concrete under crack mouth opening displacement (CMOD) control. Crack growth was monitored by applying the acoustic emission (AE) technique. In order to improve our understanding of the FPZ, the width and length of the FPZ were followed based on the AE source locations maps and several AE parameters were studied during the entire loading process. The bvalue analysis, defined as the log-linear slope of the frequency-magnitude distribution of acoustic emissions, was also carried out to describe quantitatively the influence of the relative notch depth on the fracture process. The results show that the number of AE hits increased with the decrease of the relative notch depth and an important AE energy dissipation was observed at the crack initiation in unnotched beams. In addition, the relative notch depth influenced the AE characteristics, the process of crack propagation, and the brittleness of concrete.

Wide Range Compliance Solutions for Various Fracture Test Specimens Using Crack Mouth Opening Displacement

2017 ◽  
Author(s):  
Claudio Ruggieri ◽  
Rodolfo F. de Souza
Keyword(s):  
Mouth Opening ◽  
Crack Mouth Opening Displacement ◽  
Width Ratio ◽  
Fracture Test ◽  
Single Edge ◽  
Opening Displacement ◽  
Element Analysis ◽  
Single Edge Notch ◽  
Wide Range ◽  
Edge Notch

This work addresses the development of wide range compliance solutions for tensile-loaded and bend specimens based on CMOD. The study covers selected standard and non-standard fracture test specimens, including the compact tension C(T) configuration, the single edge notch tension SE(T) specimen with fixed-grip loading (clamped ends) and the single edge notch bend SE(B) geometry with varying specimen spam over width ratio and loaded under 3-point and 4-point flexural configuration. Very detailed elastic finite element analysis in 2-D setting are conducted on fracture models with varying crack sizes to generate the evolution of load with displacement for those configurations from which the dependence of specimen compliance on crack length, specimen geometry and loading mode is determined. The extensive numerical analyses conducted here provide a larger set of solutions upon which more accurate experimental evaluations of crack size changes in fracture toughness and fatigue crack growth testing can be made.

TEST STUDY ON THE BEST PASTING LAYER OF FRP REINFORCED CONCRETE

2019 ◽  
Vol 27 (02) ◽  
pp. 1950105
Author(s):  
XIANGQIAN FAN ◽  
JUEDING LIU
Keyword(s):  
Fracture Toughness ◽  
Acoustic Emission ◽  
Reinforced Concrete ◽  
Crack Depth ◽  
Mouth Opening ◽  
Bending Test ◽  
Crack Mouth Opening Displacement ◽  
Displacement Curve ◽  
Crack Mouth ◽  
Opening Displacement

To optimize the strengthening method using the fiber reinforced polymer (FRP) for the reinforcement of the concrete structure with cracks, the three-point bending test was conducted on the concrete beams wrapped with different layers of FRP materials. The strain gauges were pasted on the surface of the specimens to measure the initial cracking load. The crack mouth opening displacement (CMOD) was utilized to test the load–crack mouth opening displacement curve. According to the improved calculation formula of the fracture toughness, the critical effect crack length [Formula: see text], initiation fracture toughness [Formula: see text] and instability fracture toughness [Formula: see text] of specimens were calculated. The test results showed that, under the same initial crack depth, the peak load of FRP reinforced concrete decreases with the increase of FRP pasting layer. When there was one layer wrapped over the specimen, the instability toughness of the specimen reached the maximum value and the crack resistance was the best. Based on acoustic emission testing method, the acoustic emission parameters of the above-mentioned concrete during fracture process were identified and collected. The optimal layer of the FRP reinforced concrete with cracks was analyzed from the acoustic emission method.

Experimental Determination of J-R Curves Using SENB Specimens and P-CMOD Data

2008 ◽  
Author(s):  
Xian-Kui Zhu ◽  
Brian N. Leis
Keyword(s):  
Crack Extension ◽  
Mouth Opening ◽  
Cost Effective ◽  
Crack Mouth Opening Displacement ◽  
Simple Relationship ◽  
J Integral ◽  
Single Specimen ◽  
Opening Displacement ◽  
Load Line Displacement ◽  
Senb Specimen

Fracture toughness and J-R curves of ductile materials are often measured under the guidance of ASTM standard E1820 using the single specimen technique and the elastic unloading compliance method. For the standard single-edge notched bend [SENB] specimens, the load, load-line displacement (LLD), and crack-mouth opening displacement (CMOD) are required being measured simultaneously. The load-CMOD data are used to determine the crack extension, and the load-LLD data together with the crack extension are used to determine the J-integral values in a J-R curve test. Experiments have indicated that the CMOD measurement is very accurate, but the LLD measurement is difficult and less accurate in a fracture test on the SENB specimen. If the load-CMOD records is used to determine the crack extension and the J-integral values, experimental accuracies for the J-R curve testing would be increased, and the test costs can be reduced. To this end, this paper develops a simple relationship between LLD and CMOD that is used to convert the measured CMOD record to the corresponding LLD data, and then to calculate the J values for a growing crack in a J-R curve test on the SENB specimen using one single specimen technique. The proposed method is then verified by the experimental data of J-R curves for HY80 steel using the SENB specimens and the load-CMOD data only. The results show that the proposed method is more accurate and more cost-effective for the J-R curve testing.

Sign in / Sign up

Export Citation Format

Share Document