scholarly journals PHYSICAL AND MECHANICAL PROPERTIES RESEARCH AND ANALYSIS OF CONCRETE WITH BIOFUEL COMBUSTION FLY ASH SUPPLEMENT

2019 ◽  
Vol 11 (0) ◽  
pp. 1-5
Author(s):  
Deividas Augutis ◽  
Džigita Nagrockienė
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Physical And Mechanical Properties ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Ash Content ◽  
Closed Porosity ◽  
Freeze Thaw ◽  
Materials Used

Materials used for the study: Portland cement CEM I 42,5 R, 0/4 fraction sand, 4/16 fraction gravel, biofuel fly ash, superplastizer ViscoCrete D187 (V) and water. Seven compositions of concrete were designed by replacing 0%, 5%, 10%, 15%, 20%, 25% and 30% of cement with biofuel fly ash. The article analyses the effect of biofuel fly ash content on the properties of concrete. Studies have shown that the increase of biofuel fly ash content up to 15% increases concrete density and compressive strengh after 28 days of curing, compressive strength, ultrasonic pulse velocity, closed porosity, concrete forecasted freeze-thaw cycles and decreases water absorbtion, open porosity.

Mechanical properties and freeze-thaw resistances of bronze-concrete composites

2021 ◽  
Vol 12 (2) ◽  
pp. 39
Author(s):  
Tuba Bahtli ◽  
Nesibe Sevde Ozbay
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Test Methods ◽  
Pulse Velocity ◽  
Plastic Energy ◽  
Freeze Thaw ◽  
Schmidt Rebound Hammer

Studies in the literature show that the physical and mechanical properties of concrete could be improved by the incorporation of different kinds of industrial waste, including waste tire rubber and tire steel. Recycling of waste is important for economic gain and to curb environmental problems. In this study, finely ground CuAl10Ni bronze is used to improve the physical and mechanical properties, and freeze-thaw resistances of C30 concrete. The density, cold crushing strength, 3-point bending strength, elastic modulus, toughness, and freeze-thaw resistances of concrete are determined. In addition, the Schmidt Rebound Hammer (SRH) and the ultrasonic pulse velocity (UPV) tests, which are non-destructive test methods, are applied. SEM/EDX analyses are also carried out. It is noted that a more compacted structure of concrete is achieved with the addition of bronze sawdust. Then higher density and strength values are obtained for concretes that are produced by bronze addition. In addition, concretes including bronze sawdust generally show higher toughness due to high plastic energy capacities than pure concrete.

Ultrasonic pulse velocity for the evaluation of physical and mechanical properties of a highly porous building limestone

Ultrasonics ◽  
2015 ◽  
Vol 60 ◽  
pp. 33-40 ◽  
Author(s):  
Emilia Vasanelli ◽  
Donato Colangiuli ◽  
Angela Calia ◽  
Maria Sileo ◽  
Maria Antonietta Aiello
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Highly Porous

scholarly journals Comparative study on physical and mechanical properties of high slump and zero lump high volume fly ash concrete (HVFAC)

2013 ◽  
Vol 15 (4) ◽  
pp. 578-584 ◽  
Keyword(s):  
Experimental Investigation ◽  
Fly Ash ◽  
Physical And Mechanical Properties ◽  
High Volume ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Fly Ash Concrete ◽  
High Volume Fly Ash ◽  
Class F Fly Ash

<p>An experimental investigation was carried out to compare the compressive strength of zero slump and high slump concrete with high volume fly ash. 40% to 70% replacements of OPC (by weight) with class F fly ash have been incorporated. Superplasticizer was added at 1% of binder (cement + fly ash) to the zero slump mixture to get a slump in the range of 140 to 180mm and cubes were cast without compaction. The results showed that the apparent porosity and water absorption were higher for zero slump concrete than high slump concrete. Zero slump concrete showed better compressive strengths than superplasticized concrete with 40 to 60% fly ash addition for all curing times tested (3,7 and 28 days). Ultrasonic pulse velocity results categorized all mixes as of &lsquo;EXCELLENT&rsquo; concrete quality. Based on the present experimental investigation, it can be concluded that high volume fly ash concrete is suitable for general construction applications.</p>

PERFORMANCE OF SAWDUST CONCRETE AT ELEVATED TEMPERATURE

2017 ◽  
Vol 80 (1) ◽  
Author(s):  
Ruhal Pervez Memon ◽  
Lemar Achekzai ◽  
Abdul Rahman Mohd. Sam ◽  
A. S. M. Abdul Awal ◽  
Uroosa Memon
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperature ◽  
Fire Resistance ◽  
Lightweight Concrete ◽  
Physical And Mechanical Properties ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Waste Material ◽  
Lower Amount

The aim of this study was to shows the behavior of sawdust concrete at elevated temperature. Sawdust is considered as waste material but nowadays this waste material is utilized in the construction of the building as sawdust concrete. Sawdust is a by-product of wood which is generally used in the production of lightweight concrete, possessing low thermal conductivity. In this study sawdust concrete was made at three different proportions of cement and sawdust 1:1, 1:2, 1:3 by volume. At these proportions, the physical and mechanical properties such as density, workability, strength, fire resistance, mass loss, ultrasonic pulse velocity and residual strength were investigated after 28 days of curing. It was found that with the increment in the amount of sawdust, the workability and strength decreases, however in terms of fire resistance, concrete with lower amount of sawdust performed well. Considering the overall physical and mechanical properties, sawdust concrete can be used in building construction. 

scholarly journals Stress-Strain Behaviour and Mechanical Strengths of Concrete Incorporating Mixed Recycled Plastics

2021 ◽  
Vol 5 (6) ◽  
pp. 146
Author(s):  
Mahmoud Abu-Saleem ◽  
Yan Zhuge ◽  
Reza Hassanli ◽  
Mark Ellis ◽  
Md Mizanur Rahman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Coarse Aggregates ◽  
Strain Behaviour ◽  
Plastic Concrete ◽  
Indirect Tensile ◽  
Recycled Plastics

Different types of recycled plastic have been used in concrete and most studies have focused on the behaviour of a single type of plastic. However, separating plastic wastes increases the cost and time of processing. To tackle this problem, this research presents an experimental investigation to determine the effect of incorporating different combinations of three types of recycled plastic waste aggregates—Polyethylene terephthalate (PET), High Density Polyethylene (HDPE) and Polypropylene (PP)—at different replacement ratios of coarse aggregate on physical and mechanical properties of concrete. The combinations include two plastic types at 10% and 20% replacement ratios and three plastic types at 15% and 30% replacement ratios. The performance of the plastic concrete was assessed based on various physical and mechanical properties including workability, fresh and dry densities, air content, compressive, indirect tensile and flexural strengths, modulus of elasticity, stress-strain behaviour and ultrasonic pulse velocity. It is found that the workability of Mixed Recycled Plastic Concrete (MRPC) at a low replacement rate is independent of the type of plastic. The minimum reduction in the compressive strength, indirect tensile and modulus of elasticity were achieved by R3 (PET + PP) at 10% replacement, while R5 (HDPE + PP) at 10% replacement achieved the highest flexural strength and ultrasonic pulse velocity values. The findings suggest that the mixed recycled plastics have a good possibility to partially replace coarse aggregates in concrete which will benefit the plastics recycling community and environment. Furthermore, the study will provide guidance to the concrete industry concerning the effect of the implementation of unsorted mixed types of plastic as coarse aggregates in the production of concrete.

scholarly journals The effect of glass powder on physical and mechanical properties of hardened cement paste

2019 ◽  
Author(s):  
Kęstutis Barkauskas ◽  
Džigita Nagrockienė ◽  
Ingrida Girnienė
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Physical And Mechanical Properties ◽  
Glass Particle ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Hardened Cement ◽  
Hardened Cement Paste ◽  
Materials Used

The article analyses the effect of finely crushed glass on the properties of hardened cement paste. Materials used for the test: Portland cement CEM I 42.5 R, finely crushed glass (particle size ≤75 µm), and water. Seven compositions of cement paste mixes with different amounts of crushed glass (0%, 5%, 10%, 15%, 20%, 25%, 30%) added by weight of cement were designed. Compressive strength, density and ultrasonic pulse velocity of modified hardened cement paste with different content of crushed glass were measured in the tests. The test results revealed the increase of density, ultrasonic pulse velocity and compressive strength in specimens of hardened cement paste containing 5% and higher percentage of crushed glass after 7, 28 and 56 days of hardening. Microstructure tests revealed that crushed glass had an effect on the microstructure of hardened cement paste after 7 days of curing. X-ray analysis revealed the effect of crushed glass on the physical composition of hardened cement paste hydration products. Hardened cement paste containing 5% of crushed glass by weight of cement was found to have higher strength and density compared to unmodified cement paste.

scholarly journals Correlation of physical and mechanical properties with ultrasonic pulse velocities of sandstones in Çenedağ, Kocaeli-Turkey

2017 ◽  
Vol 5 (2) ◽  
pp. 109 ◽  
Author(s):  
Metin Aşcı ◽  
İsmail Kaplanvural ◽  
Ahmet Karakaş ◽  
Özgün Kamil Şahin ◽  
Cengiz Kurtuluş
Keyword(s):  
Mechanical Properties ◽  
Mass Density ◽  
Physical And Mechanical Properties ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Point Load ◽  
Statistical Correlations ◽  
Lower Ordovician ◽  
Schmidt Hardness

Correlation of physical and mechanical properties with ultrasonic pulse velocities (UPV) of sandstones in Çenedağ, Kocaeli-Turkey, NW was performed in this study. Physical and mechanical properties were defined and the relationships among the uniaxial compressive strength (UCS), porosity, void ratio, point load strength index Is(50),Schmidt hardness (RN) and bulk mass density by weight with ultrasonic pulse velocity of pink and cream colored sandstone unit of Lower Ordovician Çenedağ formation were investigated. In the scope of this research, 16 sandstone specimens were collected from various locations of Çenedağ formation in Çenedağ-Kocaeli, Turkey and laboratory experiments were implemented. Later, the statistical correlations were performed by regression analysis to evaluate the relationships between these properties and ultrasonic pulse velocity. Reasonably good correlations were determined between the UPV and physical and mechanical properties.

The Effect of Chloride Environment on Mechanical Properties Geopolymer Binder with Fly Ash

2013 ◽  
Vol 594-595 ◽  
pp. 648-655 ◽  
Author(s):  
Muhammad Sigit Darmawan ◽  
Ridho Bayuaji ◽  
Boedi Wibowo ◽  
Nur Ahmad Husin ◽  
Srie Subekti
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Design Method ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
National Standard ◽  
Vacuum Saturation ◽  
Chloride Environment

This study is conducted to determine the effect of five variables on mechanical properties of geopolymer binders. These five variables are chloride environment, NaOH molarity, Na2SiO3/NaOH ratio, fly ash/alkaline activator (FA/AA) ratio and superplasticizer (SP) addition. The mechanical properties considered are compressive strength, porosity and density. Taguchi experimental design method is used to compile the binder composition of geopolymer to achieve the maximum compressive strength. Specimens binder used is a cylinder with 25 mm diameter and 50 mm height. Compressive strength test is performed at 28 days using SNI 03-6825-2002 (Indonesian National Standard) and porosity of the binder is determined using vacuum saturation apparatus similar to that developed by RILEM. The density of the binder is measured using Ultrasonic Pulse Velocity (UPV). This study concludes that the chloride environment has a beneficial effect on the compressive strength of the binder. In addition, the FA/AA ratio and NaOH molarity give a significant effect on the compressive strength of geopolymer binders.

Sign in / Sign up

Export Citation Format

Share Document