scholarly journals HPLC method for simultaneous determination of impurities and degradation products in Cardiazol

Pharmacia ◽  
2020 ◽  
Vol 67 (1) ◽  
pp. 29-37
Author(s):  
Iryna Drapak ◽  
Borys Zimenkovsky ◽  
Liudas Ivanauskas ◽  
Ivan Bezruk ◽  
Lina Perekhoda ◽  
...  
Keyword(s):  
Flow Rate ◽  
Mobile Phase ◽  
Degradation Products ◽  
Phase 1 ◽  
Simultaneous Detection ◽  
Hplc Method ◽  
Column Temperature ◽  
Degree Of Separation ◽  
Determination Of Impurities

Aim. The aim of study was to develop a simple and accurate procedure that could be applied for the determination of impurities and degradation products in cardiazol. Materials and methods. Separation in samples was carried out with Acquity H-class UPLC system (Waters, Milford, USA) equipped with Acquity UPLC BEH C18 column (2.1 × 50 mm, 1.7 μm) (Waters, Milford, USA). Xevo TQD triple quadrupole mass spectrometer detector (Waters Millford, USA) was used to obtain MS/MS data. Mobile phase A: 0.1% solution of trifluoroacetic acid R in water R; Mobile phase B: acetonitrile R. Samples were chromatographed in gradient mode (Table 1). Flow rate of the mobile phase: 1 ml / min. Column temperature: 30 °С. Detection: at 240 nm wavelength. Injection volume: 10 μl. Results. The retention time of the main substance is about 18.5 minutes. The order of the peak, the retention times and relative retention times: impurity B (12.04, 0.65); impurity А (18.5; 0.98); Cardiazol (18.87; 1.00). The LOD and LOQ values obtained were in the range of 30 ng/mL to 100 ng/mL and 80 ng/mL to 310 ng/mL respectively (with respect to sample concentration of 2 mg/ml). Linearity was established in the range of LOQ level to 0.2% having regression coefficients in the range of 0.9996 to 0.9999. The change in the temperature of the column affects the degree of separation of cardiazol and the impurity A, and thus, with a decrease of 5 ° C, the degree of separation is (1.06), while with increasing this index (3.43). When changing the flow rate of the mobile phase, the degree of separation changes in the following order, with a decrease to 0.9 ml / min separation (1.90), with an increase in speed to 1.1 ml / min (2.45). When the number of mobile phase B decreases by 5%, the degree of separation varies by (2.65), with an increase of 5% (1.82). In comparison with the chromatogram of the tested solution, the substance is not resistant to the action of peroxide, alkaline and acid decomposition. Conclusion. 1) HPLC method was developed and validated for the simultaneous detection and quantitation of impurities formed during the synthesis of cardiazol. 2) The method proved to be sensitive, selective, precise, linear, accurate and stability-indicating.

scholarly journals THE OPTIMIZATION OF HPLC FOR QUANTITATIVE ANALYSIS OF ACID ORANGE 7 AND SUDAN II IN COSMETIC PRODUCTS USING BOX BEHNKEN DESIGN

2019 ◽  
pp. 130-137 ◽  
Author(s):  
NOVALINA BR PURBA ◽  
ABDUL ROHMAN ◽  
SUDIBYO MARTONO
Keyword(s):  
Flow Rate ◽  
Retention Time ◽  
Mobile Phase ◽  
High Performance ◽  
Hplc Method ◽  
Acid Orange 7 ◽  
Column Temperature ◽  
Box Behnken Design ◽  
Acid Orange

Objective: The objective of this study was to optimize high-performance liquid chromatography (HPLC) method for the determination of acid orange 7 (AO7) and sudan II (SII) in blusher product based on response surface methodology using box behnken design (BBD) approach. Methods: Some factors responsible for HPLC separation including column temperature, mobile phase composition, flow rate were optimized using BBD. The responses evaluated were peak area, retention time, and tailing factor. AO7 and SII in blusher product has different properties, therefore both analytes were analysed using C18 column (Thermo Synergy Gold 250 mm x 4.6 mm i.d.,5 µm) using Shimadzu LC 20AD chromatograph equipped with photo-diode array (PDA) detector at 300-650 nm. The mobile phase used was acetonitrile-water (1:1 v/v), and acetonitrile composition was optimized at 35-50% for separation AO7 (ACN1), and 80-90% for SII (ACN2), delivered at the flow rate of 0.9–1 ml/min, using column temperature at 30-40 °C. Results: BBD showed that separation of AO7 was influenced by the concentration of ACN1, flow rate and column temperature. These factors affected retention time, peak area, and tailing factor with peak area was the most significant. Tailing factor was not significantly affected by each factor, and retention time was slightly effected. Otherwise, Sudan II was affected by all these factors except ACN1. The optimal condition obtained based BBD was ACN1 43%, ACN2 90%, the flow rate of 0.9 ml/min and a column temperature of 40 °C. Conclusion: BBD can be used to get optimum condition for analysis of AO7 and SII in blusher product.

scholarly journals RP-HPLC Method Development and Validation for the Estimation of Lansoprazole in Presence of Related Substances by QbD Approach

2021 ◽  
pp. 138-150
Author(s):  
Sachin B. Gholve ◽  
Jaiprakash N. Sangshetti ◽  
Omprakash G. Bhusnure ◽  
Ram S. Sakhare ◽  
Pratap H. Bhosale ◽  
...  
Keyword(s):  
Flow Rate ◽  
Mobile Phase ◽  
Method Development ◽  
Hplc Method ◽  
Drug Substance ◽  
Gastric Ulcers ◽  
Mobile Phase Flow Rate ◽  
Column Temperature ◽  
Rp Hplc

A rapid specific RP-HPLC method has been developed for the determination of Lansoprazole impurities in the drug substance. The control of pharmaceutical impurities is currently a critical issue in the pharmaceutical industry. The International Council for Harmonization (ICH) has formulated a workable guideline regarding the control of impurities. The objective of the recent study was to develop and validate a HPLC method for the quantitative determination of process-related impurities of Lansoprazole in pharmaceutical drug substance. Lansoprazole, 2-[[[3-methyl-4-(2,2,2-trifluoroethoxy)-2-pyridinyl] methyl]-sulfinyl]- 1H-benzimidazole is an proton pump inhibitor used in the management of gastric ulcers. Chromatographic identification of the impurities was carried out by response surface methodology, applying a three-level Box Behnken design with three center points. Three factors selected were a mobile phase, flow rate, column temperature. Evaluation of the main factor, their interaction, and the quadric effect on peak resolution were done on Waters Symmetry C8, 250 x 4.6mm, 5µm column is used for the development of the method. The mobile phase consists of buffer and acetonitrile. The flow rate of the mobile phase was 1.0 ml/min with gradient elution. The column temperature is ambient and the detection wavelength is 235 nm. The injection volume was 10 µL. The method was validated as per ICH guidelines for linearity in the range of 50-150 µg/ml and the LOD & LOQ values obtained were 0.437×10-4 and 0.1325×10-3 µg/ml respectively which specifies the method's sensitivity. The proposed method was successfully used to determine the Lansoprazole impurities in drug substances.

scholarly journals Selective Determination of Diazinon and Chlorpyrifos in the Presence of Their Degradation Products: Application to Environmental Samples

2018 ◽  
Vol 101 (4) ◽  
pp. 1191-1197 ◽  
Author(s):  
Mamdouh R Rezk ◽  
Abd El-Aziz B Abd El-Aleem ◽  
Shaban M Khalile ◽  
Omneya K El-Naggar
Keyword(s):  
Flow Rate ◽  
Environmental Samples ◽  
Mobile Phase ◽  
Degradation Products ◽  
Hplc Method ◽  
Stress Conditions ◽  
Uv Detection ◽  
Selective Determination ◽  
International Conference

Abstract An accurate, sensitive, and selective HPLC method was developed and validated for the determination of diazinon and chlorpyrifos. These pesticides were subjected to different stress conditions, such as acidic, alkaline, oxidative, thermal, and photolytic hydrolysis. The proposed method used a C18 Eclipse Plus column (100 × 4.6 mm, 3.5 µm) and a mobile phase consisting of acetonitrile–water (70 + 30, v/v) in an isocratic separation mode. The flow rate was 1.5 mL/min, with UV detection at 247 and 230 nm for diazinon and chlorpyrifos, respectively. The proposed method was linear over the range of 0.40–50.00 µg/mL for diazinon and 0.40–40.00 µg/mL for chlorpyrifos. The proposed method was validated per International Conference on Harmonization guidelines and subsequently applied for the successful determination of the studied pesticides in bulk form in their commercial samples in the presence of their degradation products. The developed method was used for the determination of the residues of these pesticides in lavender and rosemary leaves that were pretreated with the recommended doses of these pesticides.

scholarly journals A Simple and Convenient Method for Simultaneous Determination ofSchizandrol A,Schizandrol B,Schisandrin A,γ-Schisandrin, andSchisandrin C

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Yu Zhou ◽  
Wu Ling Wei ◽  
Jiang Xing Hua ◽  
Qingsheng Fan
Keyword(s):  
Simultaneous Determination ◽  
Flow Rate ◽  
Convenient Method ◽  
Mobile Phase ◽  
Gradient Elution ◽  
Hplc Method ◽  
Schisandra Chinensis ◽  
Column Temperature

A simple, rapid, and specific HPLC method was established for simultaneous determination of five major lignans (Schizandrol A,Schizandrol B,Schisandrin A,γ-Schisandrin, andSchisandrin C) inSchisandra chinensis. The five lignans can be separated completely on Kromasil C18column (250 nm × 4.6 nm) and then detected at 254 nm using methanol (mobile phase A) and water (mobile phase B) with gradient elution as the mobile phase at 1.0 mL/min flow rate. The column temperature was 30°C. The method was validated in terms of linearity, precision, stability, repeatability, and recovery. Results showed that the method is accurate and reproducible.

scholarly journals A Validated RP-HPLC Method and Force Degradation Studies of Fexofenadine Hydrochloride in Pharmaceutical Dosage Form

2018 ◽  
Vol 17 (1) ◽  
pp. 43-50
Author(s):  
Sherejad Sanam ◽  
Sharmin Nahar ◽  
Nazmus Saqueeb ◽  
SM Abdur Rahman
Keyword(s):  
Flow Rate ◽  
Mobile Phase ◽  
Limit Of Detection ◽  
Degradation Products ◽  
Parent Compound ◽  
Hplc Method ◽  
Pharmaceutical Dosage Form ◽  
Rp Hplc ◽  
Fexofenadine Hcl

A stability indicating HPLC method was developed and validated for the quantitative determination of fexofenadine hydrochloride. An isocratic separation was achieved using phenomenex (C18) column (250×4.6 mm, 5 μm) with flow rate of 1.0 ml/min and UV detection at 254 nm. The mobile phase consists of 5Mm acetate buffer: acetonitrile (50:50; v/v) with pH 9.4 adjusted with acetic acid. The drug was subjected to oxidative, acidic, basic, neutral, photolytic and thermal degradation. All degradation products were eluted in an overall analytical run time of approximately 40 min with the parent compound fexofenadine hydrochloride at a flow rate of approximately 3.3±0.3 min. The method was linear over the concentration range of 31.5-500 μg/ml (r2 = 0.999) with limit of detection and quantification of 3.5 μg/ml and 10.1 μg/ml, respectively. The method has the requisite accuracy, selective, precision and robustness to assay fexofenadine HCl in tablets.Dhaka Univ. J. Pharm. Sci. 17(1): 43-50, 2018 (June)

scholarly journals Box-Behnken Assisted Validation and Optimization of an RP-HPLC Method for Simultaneous Determination of Domperidone and Lansoprazole

Separations ◽  
2021 ◽  
Vol 8 (1) ◽  
pp. 5
Author(s):  
Mohd Afzal ◽  
Mohd. Muddassir ◽  
Abdullah Alarifi ◽  
Mohammed Tahir Ansari
Keyword(s):  
Flow Rate ◽  
Mobile Phase ◽  
Limit Of Detection ◽  
Hplc Method ◽  
Box Behnken Design ◽  
Rp Hplc ◽  
System Suitability ◽  
Method Optimization ◽  
Key Variables

A highly specific, accurate, and simple RP-HPLC technique was developed for the real-time quantification of domperidone (DOMP) and lansoprazole (LANS) in commercial formulations. Chromatographic studies were performed using a Luna C8(2), 5 μm, 100Å, column (250 × 4.6 mm, Phenomenex) with a mobile phase composed of acetonitrile/2 mM ammonium acetate (51:49 v/v), pH 6.7. The flow rate was 1 mL·min−1 with UV detection at 289 nm. Linearity was observed within the range of 4–36 µg·mL−1 for domperidone and 2–18 µg·mL−1 for lansoprazole. Method optimization was achieved using Box-Behnken design software, in which three key variables were examined, namely, the flow rate (A), the composition of the mobile phase (B), and the pH (C). The retention time (Y1 and Y3) and the peak area (Y2 and Y4) were taken as the response parameters. We observed that slight alterations in the mobile phase and the flow rate influenced the outcome, whereas the pH exerted no effect. Method validation featured various ICH parameters including linearity, limit of detection (LOD), accuracy, precision, ruggedness, robustness, stability, and system suitability. This method is potentially useful for the analysis of commercial formulations and laboratory preparations.

scholarly journals RP-HPLC Determination of Raloxifene in Pharmaceuticl Tablets

2006 ◽  
Vol 3 (1) ◽  
pp. 60-64 ◽  
Author(s):  
P. Venkata Reddy ◽  
B. Sudha Rani ◽  
G. Srinu Babu ◽  
J. V. L. N. Seshagiri Rao
Keyword(s):  
Flow Rate ◽  
Retention Time ◽  
Mobile Phase ◽  
Dosage Forms ◽  
Hplc Method ◽  
Reverse Phase Hplc ◽  
Reverse Phase ◽  
Pharmaceutical Dosage Forms ◽  
Rp Hplc

A reverse phase HPLC method is developed for the determination of Raloxifene in pharmaceutical dosage forms. Chromatography was carried out on an inertsil C18 column using a mixture of acetonitrile and phosphate buffer (30:70 v/v) as the mobile phase at a flow rate of 1 mL/min. Detection was carried out at 290 nm .The retention time of the drug was 10.609 min. The method produced linear responses in the concentration range of 0.5-200 µg/mL of Raloxifene. The method was found to be applicable for determination of the drug in tablets.

scholarly journals Photostability study of amlodipine besylate tablets packed in primary packaging

2021 ◽  
Vol 10 (1) ◽  
pp. 20-28
Author(s):  
Ivana Savić-Gajić ◽  
Ivan Savić ◽  
Predrag Sibinović ◽  
Valentina Marinković
Keyword(s):  
Mobile Phase ◽  
Limit Of Detection ◽  
Degradation Products ◽  
Hplc Method ◽  
Coefficient Of Determination ◽  
Amlodipine Besylate ◽  
Limit Of Quantification ◽  
First Order Kinetics ◽  
The Given

In this study, the modified stability-indicating RP-HPLC method was validated for quantitative analysis of amlodipine besylate in the presence of its impurity D (3-ethyl 5-methyl 2-[(2-aminoethoxy)methyl]-4-(2-chlorophenyl)-6-methylpyridine-3,5-dicarboxylate). The method was applied for the determination of an analyte in the tablets and irradiated samples packed in the primary packaging (Alu/PVC/PVDC blister packaging). The efficient chromatographic separation was achieved using a ZORBAX Eclipse XDB-C18 column (4.6×250 mm, 5 mm) with isocratic elution of mobile phase which consisted of acetonitrile:methanol:triethylamine solution (15:35:50, v/v/v) (pH 3.0). The flow rate of the mobile phase was 1 mL min-1, while the detection of amlodipine besylate was carried out at 273 nm. Amlodipine besylate and its impurity D were identified at the retention times of 16.529 min and 2.575 min, respectively. The linearity of the method with the coefficient of determination of 0.999 was confirmed in the concentration range of 10 - 75 µg mL-1 for amlodipine besylate. The limit of detection was 0.2 µg mL-1, while the limit of quantification was 0.66 µg mL-1. After UV and Vis radiation of the tablets packed in the primary packaging, the content of amlodipine besylate was reduced by 22.38% and 19.89%, respectively. The presence of new degradation products was not detected under the given chromatographic conditions. The photodegradation of amlodipine besylate followed pseudo-first-order kinetics. Based on the half-life of amlodipine besylate (38.4 days for UV radiation and 43.3 days for Vis radiation), it was concluded that amlodipine besylate in the tablets has satisfactory photostability after its packing in the Alu/PVC/PVDC blister packaging.

scholarly journals A New Validated Stability Indicating RP-HPLC Method for Simultaneous Quantification of Formoterol Fumarate Dihydrate and Mometasone Furoate in Metered Dose Inhalation Aerosol

2021 ◽  
Vol 33 (11) ◽  
pp. 2723-2728
Author(s):  
Surya Prakash Mamillapalli ◽  
Gourabattina Lakshmi Prasanna ◽  
B. Venkata Subbaiah ◽  
N. Annapurna
Keyword(s):  
Flow Rate ◽  
Mobile Phase ◽  
Hplc Method ◽  
Mometasone Furoate ◽  
Simultaneous Estimation ◽  
Column Temperature ◽  
Stability Indicating ◽  
Metered Dose ◽  
Formoterol Fumarate ◽  
Dose Inhalation

Stability indicating reversed phase-HPLC method for simultaneous estimation of mometasone furoate (MAF) and formoterol fumarate (FFD) in metered dose inhalation aerosol (MDI) dosage formulation has been developed and discussed in the present work. The chromatographic separation was achieved using Hypersil ODS column (250 mm × 4.6 mm, 3 μm) using an isocratic separation mode at a flow rate of 1.2 mL/min, column temperature of 50 ºC. The system operates with a mobile phase comprising of solution-A (buffer): Solution-B (acetonitrile) mixed in the ratio of 70:30 %v/v at a UV detection wavelength of 214 nm. Retention times of mometasone furoate and formoterol fumarate found to be about 3 min and 7 min, respectively. All possible degradation products of both compounds were monitored at 214 nm and spectral purity along with % mass balance is assessed using PDA detector. Both analyte were subjected to force degradation studies, found all degradants were resolved from analyte peaks and also other process-related impurities. The proposed method is validated for specificity, linearity, accuracy, precision and robustness as per ICH guidelines and found to be adequate. Method stood to be robust with variation in column temperature, flow rate, pH of buffer and organic content in mobile phase.

scholarly journals DETERMINATION OF 2-CYANO-4’-BROMOMETHYL BIPHENYL GENOTOXIC IMPURITY IN IRBESARTAN DRUG SUBSTANCES USING HPLC TECHNIQUE

2016 ◽  
Vol 8 (12) ◽  
pp. 225
Author(s):  
S. Senthil Kumar ◽  
Ritesh Kumar Srivastava ◽  
V. Srinivas Rao
Keyword(s):  
Mobile Phase ◽  
Hplc Method ◽  
Development Activity ◽  
Validation Data ◽  
Column Temperature ◽  
Injection Volume ◽  
Drug Substances ◽  
Hplc Technique ◽  
Ich Guideline

<p><strong>Objective: </strong>The objective of present study was to develop and validate a specific and sensitive HPLC method for the quantitative determination of genotoxic impurity 2-cyano-4’-bromomethyl biphenyl present in irbesartan drug substance.</p><p><strong>Methods: </strong>The development activity was conducted by HPLC with UV as a detector. The impurity was separated on Kromasil C18 250 x 4.6 mm, 5 µm analytical column with a mobile phase consisting of buffer pH 3.2 and acetonitrile in the ratio of 60:40 v/v at a flow rate 1.5 ml/min. The effluent was monitored by UV detection at 258 nm with column temperature maintained at 40 °C and the injection volume 30 μl. Acetonitrile was selected as diluent.</p><p><strong>Results: </strong>Validation activity was planned and completed based on the ICH guideline. The LOD and LOQ value were found to be 0.167 µg/g and 0.506 µg/g and accuracy results were well in the range 98.34 to 103.46 %. The linearity curve showed the correlation coefficient of 0.9999 and method very sensitive.</p><p><strong>Conclusion: </strong>From validation data, it was confirmed that the developed method is specific, sensitive, linear, precise and accurate for the determination of 2-cyano-4’-bromomethyl biphenyl genotoxic impurity in irbesartan drug substances.</p>

Sign in / Sign up

Export Citation Format

Share Document