Optimization of line configuration and balancing for flexible machining lines

2016 ◽  
Vol 29 (3) ◽  
pp. 579-587 ◽  
Author(s):  
Xuemei Liu ◽  
Aiping Li ◽  
Zurui Chen
2009 ◽  
Vol 39 (5) ◽  
pp. 412-417 ◽  
Author(s):  
Fortunato Morabito ◽  
Angela Tassinari ◽  
Vincenzo Callea ◽  
Maura Brugiatelli ◽  
Maria Teresa Fierro ◽  
...  

2012 ◽  
Vol 45 (6) ◽  
pp. 426-431 ◽  
Author(s):  
Pavel A. Borisovsky ◽  
Xavier Delorme ◽  
Alexandre Dolgui

Author(s):  
Vincenzo Nava ◽  
Marin Rajic ◽  
Carlos Guedes Soares

The aim of this paper is to study the dynamics of a floating body with characteristics comparable to a point absorber wave energy converter with different mooring systems, in geometrical configuration or in the materials. To this purpose, the dynamics of a moored buoy is investigated. The point absorber is modeled as a spherical buoy in plane two-dimensional motion, and it is studied under the action of irregular unidirectional wind-generated waves, moored to the seabed by means of one, two or three mooring lines. Two different sets of moorings are considered, and typical wires and chains used in offshore technology are considered, leading to a total of 6 case studies. A quasi-static approach is used for modeling the restoring forces needed to keep buoy into station, using an innovative iterative procedure able to predict for each time instant and for each cable the lay down length of the cable, being each mooring line allowed to be taut or slack. Approaches in the time and frequency domains are used to obtain the system responses in intermediate waters, where these facilities are usually installed. Results for all case studies are compared both in terms of statistics of response and tensions on the top of the cable.


2006 ◽  
Vol 51 (3) ◽  
pp. 502-518 ◽  
Author(s):  
Sana Belmokhtar ◽  
Alexandre Dolgui ◽  
Nikolai Guschinsky ◽  
Genrikh Levin

Oryx ◽  
2020 ◽  
pp. 1-10 ◽  
Author(s):  
Ana Teresa Marques ◽  
Ricardo C. Martins ◽  
João Paulo Silva ◽  
Jorge M. Palmeirim ◽  
Francisco Moreira

Abstract Collision with power lines is a major cause of mortality for many bird species. Understanding the biotic and abiotic factors that increase collision risk is therefore important for implementing mitigation measures to minimize mortality, such as power line rerouting or wire marking. Here, we used collision events registered during 2003–2015 along 280 km of transmission power lines in southern Portugal to analyse spatio-temporal patterns and collision risk factors in two sympatric, threatened, and collision-prone species: the great bustard Otis tarda and the little bustard Tetrax tetrax. The occurrence of collisions was not uniform across space and time, and variations could be explained by the species' ecological requirements, distribution patterns and behaviour. Although both species fly considerable distances between areas of suitable habitat, collisions were far more likely in power line sections with > 20% (for the little bustard) or > 50% (for the great bustard) of open farmland habitat in the surroundings. Power line configuration was also important: taller pylons and those with a higher number of wire levels posed a higher risk for both species. Wire marking had a small but significant effect for the little bustard, reducing collisions risk. There was, however, no similar effect for the great bustard, possibly a result of limited data. Mitigation measures should be implemented to prevent bustard collisions, including adequate route planning, ideally avoiding areas with > 20% of open habitat. Line configuration and wire marking are particularly important where such localities cannot be avoided and power lines cross areas with a high proportion of bustard habitat, including outside protected areas.


2015 ◽  
Vol 13 ◽  
pp. 161-168 ◽  
Author(s):  
R. Rambousky ◽  
J. Nitsch ◽  
S. Tkachenko

Abstract. By applying the Transmission-Line Super Theory (TLST) to a practical transmission-line configuration (two risers and a horizontal part of the line parallel to the ground plane) it is elaborated under which physical and geometrical conditions the horizontal part of the transmission-line can be represented by a classical telegrapher equation with a sufficiently accurate description of the physical properties of the line. The risers together with the part of the horizontal line close to them are treated as separate lines using the TLST. Novel frequency and local dependent reflection coefficients are introduced to take into account the action of the bends and their radiation. They can be derived from the matrizant elements of the TLST solution. It is shown that the solution of the resulting network and the TLST solution of the entire line agree for certain line configurations. The physical and geometrical parameters for these corresponding configurations are determined in this paper.


Sign in / Sign up

Export Citation Format

Share Document