Experience of the practical use of complex «Search» on the controlled from distance determination of oil-and-gas bearings areas and choice of points under well-drilling

2010 ◽  
Author(s):  
N. I. Kovalev ◽  
V. A. Gokh ◽  
S. V. Soldatova
Keyword(s):  
Oil And Gas ◽  
Well Drilling ◽  
Distance Determination ◽  
Gas Bearings

Hydrogeology correction in the gravitational field from satellite data

2018 ◽  
Vol 931 (1) ◽  
pp. 2-7
Author(s):  
V.D. Jushkin ◽  
L.V. Zotov ◽  
O.A. Khrapenko
Keyword(s):  
Gravitational Field ◽  
Oil And Gas ◽  
Repeated Measurements ◽  
Geological Factors ◽  
Grace Satellite ◽  
Gas Pumping ◽  
Acceleration Of Gravity ◽  
Determination Of Parameters ◽  
Gravity Acceleration

The results of repeated measurements of the acceleration of gravity by the Russian absolute ballistic field gravimeter GABL-M on points of oil and gas deposits in the permafrost over a five year period are presented. The changes of gravity acceleration by the absolute gravimeter and GRACE satellite were compared. The results of comparisons of differences gravity acceleration by ballistic gravimeter GABL-M and relative Canadian gravimeters CG5 were [i]shown. The errors in determination of parameters of the gravitational field ballistic gravimeter GABL-M and CG5 gravimeters group were presented. The method of measurement with the gravimeter GABL-M and the method of determining the vertical gradients relative CG5 gravity meters was described. The necessity of introducing corrections of hydrogeology is caused by influence of hydro geological factors on the gravitational field in the permafrost. They are comparable with the values of the field change in the result of gas pumping.

scholarly journals Oil and gas well drilling technology based on the system approaches and the results of application

2021 ◽  
Vol 1064 (1) ◽  
pp. 012059
Author(s):  
R R Gazizov ◽  
A P Chizhov ◽  
V E Andreev ◽  
A V Chibisov ◽  
V V Mukhametshin ◽  
...  
Keyword(s):  
Oil And Gas ◽  
Gas Well ◽  
Well Drilling ◽  
Drilling Technology ◽  
System Approaches

Determination of Bubble-Point and Dew-Point Pressure Without a Visual Cell

2014 ◽  
Author(s):  
R.. Hosein ◽  
R.. Mayrhoo ◽  
W. D. McCain
Keyword(s):  
Oil And Gas ◽  
Saturation Pressure ◽  
Volatile Oil ◽  
Phase Region ◽  
Gas Condensate ◽  
Dew Point ◽  
Bubble Point ◽  
Point Pressure ◽  
Dew Point Pressure

Abstract Bubble-point and dew-point pressures of oil and gas condensate reservoir fluids are used for planning the production profile of these reservoirs. Usually the best method for determination of these saturation pressures is by visual observation when a Constant Mass Expansion (CME) test is performed on a sample in a high pressure cell fitted with a glass window. In this test the cell pressure is reduced in steps and the pressure at which the first sign of gas bubbles is observed is recorded as bubble-point pressure for the oil samples and the first sign of liquid droplets is recorded as the dew-point pressure for the gas condensate samples. The experimental determination of saturation pressure especially for volatile oil and gas condensate require many small pressure reduction steps which make the observation method tedious, time consuming and expensive. In this study we have extended the Y-function which is often used to smooth out CME data for black oils below the bubble-point to determine saturation pressure of reservoir fluids. We started from the initial measured pressure and volume and by plotting log of the extended Y function which we call the YEXT function, with the corresponding pressure, two straight lines were obtained; one in the single phase region and the other in the two phase region. The point at which these two lines intersect is the saturation pressure. The differences between the saturation pressures determined by our proposed YEXT function method and the observation method was less than ± 4.0 % for the gas condensate, black oil and volatile oil samples studied. This extension of the Y function to determine dew-point and bubble-point pressures was not found elsewhere in the open literature. With this graphical method the determination of saturation pressures is less tedious and time consuming and expensive windowed cells are not required.

Calculation of Technical Characteristics of the Technical Fleet Vessels Involved in Ensuring Safety of the Offshore Facilities of Oil and Gas Complex

2021 ◽  
pp. 7-13
Author(s):  
S.V. Matsenko ◽  
◽  
V.M. Minko ◽  
A.A. Koshelev ◽  
V.Yu. Piven ◽  
...  
Keyword(s):  
Oil And Gas ◽  
Oil Pollution ◽  
Raw Materials ◽  
Experimental Studies ◽  
Industrial Safety ◽  
Theoretical Studies ◽  
Physical Processes ◽  
Oil Spill Response ◽  
Sea Area

Violation of industrial safety rules during the operation of offshore facilities for the production, storage and transportation of the hydrocarbon raw materials leads in the most cases to pollution of the marine environment with oil and its components. The works on localization and elimination of such pollution are carried out with the help of vessels of the technical support fleet and booms. When developing oil spill response plans at such facilities, a calculated determination of the technical characteristics of vessels and booms is required that are sufficient to carry out the planned activities. The basic design principles for determining the towing capacity of the technical fleet vessels involved in the localization and elimination of oil and oil product spills by trawling methods are given in the article. The calculation is based on theoretical studies performed by the authors of the physical processes occurring during the movement of objects of a mobile trawling order in the sea area. The results obtained during the course of theoretical studies were confirmed by the experimental studies carried out by the authors personally using the real pieces of equipment in the actual development of tasks for training spill containment by trawling. As a result, the empirical dependencies were obtained and experimentally confirmed, which can be used to calculate technical characteristics of the ships as part of the mobile orders and anchor systems as part of stationary orders intended for the localization and elimination of oil pollution. These results can be used, among other things, for the calculated substantiation of the technical characteristics of the technical fleet vessels designed to ensure safety of the offshore facilities for production, storage, and transportation of the hydrocarbon raw materials.

Oil and Gas Drilling Optimization Technologies Applied Successfully to Unconventional Geothermal Well Drilling

2021 ◽  
Author(s):  
Junichi Sugiura ◽  
Ramon Lopez ◽  
Francisco Borjas ◽  
Steve Jones ◽  
John McLennan ◽  
...  
Keyword(s):  
Geothermal Energy ◽  
Oil And Gas ◽  
Optimization Techniques ◽  
Geothermal System ◽  
Well Drilling ◽  
Geothermal Well ◽  
Gas Drilling ◽  
Drilling Tools ◽  
Drilling Optimization ◽  
Oil And Gas Drilling

Abstract Geothermal energy is used in more than 20 countries worldwide and is a clean, reliable, and relatively available energy source. Nevertheless, to make geothermal energy available anywhere in the world, technical and economic challenges need to be addressed. Drilling especially is a technical challenge and comprises a significant part of the geothermal development cost. An enhanced geothermal system (EGS) is a commercially viable thermal reservoir where two wells are interconnected by some form of hydraulic stimulation. In a commercial setting, fluid is injected into this hot rock and passes between wells through a network of natural and induced fractures to transport heat to the surface system for electricity generation. To construct EGS wells, vertical and directional drilling is necessary with purpose-built drilling and steering equipment. This is an application where oil-and-gas drilling tools and techniques can be applied. A recent well, 16A(78)-32, drilled as part of the US Department of Energy's (DOE's) Utah Frontier Observatory for Research in Geothermal Energy (FORGE) program, highlights some of the technical challenges, which include drilling an accurate vertical section, a curve section, and a 5300-ft 65° tangent section in a hard granitic formation at temperatures up to 450°F (232°C). Extensive downhole temperature simulations were performed to select fit-for-purpose drilling equipment such as purely mechanical vertical drilling tools, instrumented steerable downhole motors, measurement-while-drilling (MWD) tools, and embedded high-frequency drilling dynamics recorders. Downhole and surface drilling dynamics data were used to fine- tune bit design and motor power section selection and continuously improve the durability of equipment, drilling efficiency, and footage drilled. Drilling optimization techniques used in oil and gas settings were successfully applied to this well, including analysis of data from drilling dynamics sensors embedded in the steerable motors and vertical drilling tools, surface surveillance of mechanical specific energy (MSE), and adopting a drilling parameter roadmap to improve drilling efficiency to minimize drilling dysfunctions and equipment damages. Through drilling optimization practices, the instrumented steerable motors with proper bit selections were able to drill more than 40 ft/hr on average, doubling the rate of penetration (ROP), footage, and run length experienced in previous granite wells. This paper presents a case study in which cutting-edge oil-and-gas drilling technologies were successfully applied to reduce the geothermal well drilling time by approximately half.

The Feasibility for Potassium-Based Phosphate Brines To Serve as High-Density Solid-Free Well-Completion Fluids in High-Temperature/High-Pressure Formations

SPE Journal ◽  
2018 ◽  
Vol 24 (05) ◽  
pp. 2033-2046 ◽  
Author(s):  
Hu Jia ◽  
Yao–Xi Hu ◽  
Shan–Jie Zhao ◽  
Jin–Zhou Zhao
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Oil And Gas ◽  
Pressure Coefficient ◽  
High Density ◽  
Well Drilling ◽  
Well Completion ◽  
Oil And Gas Resources ◽  
Completion Fluids ◽  
High Temperature High Pressure

Summary Many oil and gas resources in deep–sea environments worldwide are often located in high–temperature/high–pressure (HT/HP) and low–permeability reservoirs. The reservoir–pressure coefficient usually exceeds 1.6, with formation temperature greater than 180°C. Challenges are faced for well drilling and completion in these HT/HP reservoirs. A solid–free well–completion fluid with safety density greater than 1.8 g/cm3 and excellent thermal endurance is strongly needed in the industry. Because of high cost and/or corrosion and toxicity problems, the application of available solid–free well–completion fluids such as cesium formate brines, bromine brines, and zinc brines is limited in some cases. In this paper, novel potassium–based phosphate well–completion fluids were developed. Results show that the fluid can reach the maximum density of 1.815 g/cm3 at room temperature, which makes a breakthrough on the density limit of normal potassium–based phosphate brine. The corrosion rate of N80 steel after the interaction with the target phosphate brine at a high temperature of 180°C is approximately 0.1853 mm/a, and the regained–permeability recovery of the treated sand core can reach up to 86.51%. Scanning–electron–microscope (SEM) pictures also support the corrosion–evaluation results. The phosphate brine shows favorable compatibility with the formation water. The biological toxicity–determination result reveals that it is only slightly toxic and is environmentally acceptable. In addition, phosphate brine is highly effective in inhibiting the performance of clay minerals. The cost of phosphate brine is approximately 44 to 66% less than that of conventional cesium formate, bromine brine, and zinc brine. This study suggests that the phosphate brine can serve as an alternative high–density solid–free well–completion fluid during well drilling and completion in HT/HP reservoirs.

scholarly journals An Algorithm of Management Decision-Making Regarding the Feasibility of Investing in Geological Studies of Forecasted Hydrocarbon Resources

Resources ◽  
2018 ◽  
Vol 7 (3) ◽  
pp. 47 ◽  
Author(s):  
Alexey Cherepovitsyn ◽  
Dmitry Metkin ◽  
Alexander Gladilin
Keyword(s):  
Economic Evaluation ◽  
Industrial Development ◽  
Oil And Gas ◽  
Raw Material ◽  
The Arctic ◽  
Management Decision ◽  
Material Base ◽  
Gas Field ◽  
Field Development

Currently, under the conditions of increasing depletion of hydrocarbon reserves in Russia, it is necessary to consider the resource potential of poorly-researched oil and gas objects as a factor for ensuring the sustainable development of the oil and gas complex, in the context of the concept formation of rational subsoil utilization and a circular economy. The methodology of this study is based on a clear sequence of geological and economic studies of poorly-researched oil and gas objects, including four stages, such as analysis of the raw material base, assessment of the raw material potential, determination of technological development parameters, and economic evaluation. The methods of the probabilistic estimation of oil resources of the forecasted objects with regard to geological risk are outlined. Software packages “EVA—Risk Analysis” and “EVA—Economic Evaluation of Oil and Gas Field Development Projects” were used for estimation. The result of the study is the determination of the geological and economic efficiency of the development of nine hydrocarbon objects with the determination of the order of their further geological exploration, and introduction into industrial development on the example of the poorly-researched region of the Timan-Pechora oil and gas province located in the Arctic zone.

scholarly journals О ФАКТОРАХ ЭФФЕКТИВНОЙ РЕАЛИЗАЦИИ ИНВЕСТИЦИОННЫХ ПРОЕКТОВ

World Science ◽  
2019 ◽  
Vol 3 (5(45)) ◽  
pp. 16-21
Author(s):  
Мирхамидова Д. Н. ◽  
Атаханова Ш. С. ◽  
Соатов Ф. Й.
Keyword(s):  
Oil And Gas ◽  
Oil And Gas Industry ◽  
Successful Implementation ◽  
Gas Industry ◽  
Investment Projects

In article researches on establishment of influence of geological and technology factors on efficiency of investment projects, determination of risks at implementation of investment projects in the oil and gas industry and feature and factors for successful implementation of investment projects are considered.

Sign in / Sign up

Export Citation Format

Share Document