Design of Low-Cost Solar Parabolic Through Steam Sterilization

2021 ◽  
Vol 10 (1) ◽  
pp. 50-60
Author(s):  
N. K. Sharma ◽  
Ashok Kumar Mishra ◽  
P. Rajgopal
Keyword(s):  
Heat Pipe ◽  
Low Cost ◽  
Steam Sterilization ◽  
Parabolic Trough ◽  
Theoretical Concepts ◽  
Medical Instruments ◽  
Sterilization Process ◽  
Evacuated Tube ◽  
Sun Light

The objective of this study is to develop a low cost solar parabolic trough that can be used for steam sterilization of medical instruments in small clinics where electricity is scarce and expensive. On the basis of theoretical concepts of parabola and focus-balanced parabola, the assembly of ribs and reflector sheet with evacuated tube and heat pipe has been done. The parabolic trough has been mounted on a trolley so that it can be moved easily according to direction of sun light. The designed solar parabolic trough was integrated with pressure cooker under various setups and experiments were conducted to test whether sterilization is taking place or not. To validate sterilization process, tests were also conducted by placing the infected medical instruments. The solar parabolic trough developed was able to generate and maintain steam at 121 degrees Celsius at pressure 15 psig (101.3 kN/m2) for 15 minutes. The solar parabolic trough developed was effective in sterilizing the medical instruments.

scholarly journals Energy and Environmental Analysis of a Solar Evacuated Tube Heat Pipe Integrated Thermoelectric Generator Using IoT

2022 ◽  
Author(s):  
SakthiPriya Manivannan ◽  
DivyaLaxmi Gunasekaran ◽  
Gowthami Jaganathan ◽  
Shanthi Natesan ◽  
SabariMuthu Muthusamy ◽  
...  
Keyword(s):  
Heat Pipe ◽  
Power Output ◽  
Thermoelectric Generator ◽  
Waste Heat ◽  
Recovery Process ◽  
Sensor Data ◽  
Parabolic Trough ◽  
Environmental Aspect ◽  
Pipe System ◽  
Evacuated Tube

Abstract This paper investigates the solar evacuated tube heat pipe system (SEHP) coupled with a thermoelectric generator (TEG) using the internet of things (IoT). The TEGs convert heat energy into electricity through the Seebeck effect that finds application in the waste heat recovery process for the generation of power. The present work deals with the theoretical study on solar evacuated tube heat pipe integrated TEG and it is validated experimentally using with and without parabolic trough concentrating collector. And the carbon credit of the TEG system is determined to find its potential in the environmental aspect. Also, the boost type converter is used to raise the power output by increasing the voltage from the TEG for rural electrifications. However, it is found that the maximum power output due to the influence of the parabolic trough concentrator results in increased efficiency when compared with the non-concentrating SEHP-TEG system. The TEG output power can be boosted up to a maximum of 5.98 V using a power electronic boost converter. Besides, the recorded real sensor data with Arduino is implemented in the experimental process for automatic remote monitoring of the temperature.

A new desalination system using a combination of heat pipe, evacuated tube and parabolic trough collector

2015 ◽  
Vol 99 ◽  
pp. 141-150 ◽  
Author(s):  
H. Jafari Mosleh ◽  
S. Jahangiri Mamouri ◽  
M.B. Shafii ◽  
A. Hakim Sima
Keyword(s):  
Heat Pipe ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Evacuated Tube

scholarly journals Modification of a Solar Thermal Collector to Promote Heat Transfer inside an Evacuated Tube Solar Thermal Absorber

2021 ◽  
Vol 11 (9) ◽  
pp. 4100
Author(s):  
Rasa Supankanok ◽  
Sukanpirom Sriwong ◽  
Phisan Ponpo ◽  
Wei Wu ◽  
Walairat Chandra-ambhorn ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Solar Thermal ◽  
Heat Transfer Fluid ◽  
Small Scale ◽  
Medium Temperature ◽  
Change Behavior ◽  
Set Up ◽  
Evacuated Tube ◽  
Heating Medium

Evacuated-tube solar collector (ETSC) is developed to achieve high heating medium temperature. Heat transfer fluid contained inside a copper heat pipe directly affects the heating medium temperature. A 10 mol% of ethylene-glycol in water is the heat transfer fluid in this system. The purpose of this study is to modify inner structure of the evacuated tube for promoting heat transfer through aluminum fin to the copper heat pipe by inserting stainless-steel scrubbers in the evacuated tube to increase heat conduction surface area. The experiment is set up to measure the temperature of heat transfer fluid at a heat pipe tip which is a heat exchange area between heat transfer fluid and heating medium. The vapor/ liquid equilibrium (VLE) theory is applied to investigate phase change behavior of the heat transfer fluid. Mathematical model validated with 6 experimental results is set up to investigate the performance of ETSC system and evaluate the feasibility of applying the modified ETSC in small-scale industries. The results indicate that the average temperature of heat transfer fluid in a modified tube increased to 160.32 °C which is higher than a standard tube by approximately 22 °C leading to the increase in its efficiency by 34.96%.

scholarly journals Optimal design of the solar tracking system of parabolic trough concentrating collectors

2020 ◽  
Vol 15 (4) ◽  
pp. 613-619
Author(s):  
Li Kong ◽  
Yunpeng Zhang ◽  
Zhijian Lin ◽  
Zhongzhu Qiu ◽  
Chunying Li ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Solar Radiation ◽  
Tracking System ◽  
Low Cost ◽  
Parabolic Trough ◽  
The North ◽  
Tracking Mode ◽  
Solar Tracking ◽  
East West

Abstract The present work aimed to select the optimum solar tracking mode for parabolic trough concentrating collectors using numerical simulation. The current work involved: (1) the calculation of daily solar radiation on the Earth’s surface, (2) the comparison of annual direct solar radiation received under different tracking modes and (3) the determination of optimum tilt angle for the north-south tilt tracking mode. It was found that the order of solar radiation received in Shanghai under the available tracking modes was: dual-axis tracking > north-south Earth’s axis tracking > north-south tilt tracking (β = 15°) > north-south tilt tracking (β = 45) > north-south horizontal tracking > east-west horizontal tracking. Single-axis solar tracking modes feature simple structures and low cost. This study also found that the solar radiation received under the north-south tilt tracking mode was higher than that of the north-south Earth’s axis tracking mode in 7 out of 12 months. Therefore, the north-south tilt tracking mode was studied separately to determine the corresponding optimum tilt angles in Haikou, Lhasa, Shanghai, Beijing and Hohhot, respectively, which were shown as follows: 18.81°, 27.29°, 28.67°, 36.21° and 37.97°.

Evacuated Tube Heat Pipe Solar Collectors Applied to Recirculation Loop in a Federal Building: SSA Philadelphia

Solar Energy ◽  
2004 ◽  
Author(s):  
Andy Walker ◽  
Fariborz Mahjouri ◽  
Robert Stiteler
Keyword(s):  
Solar Energy ◽  
Heat Pipe ◽  
Heat Loss ◽  
Heating System ◽  
Hot Water ◽  
Solar Array ◽  
Solar Collectors ◽  
Water Heating ◽  
Evacuated Tube ◽  
Recirculation Loop

This paper describes design, simulation, construction and measured initial performance of a solar water heating system (360 Evacuated Heat-Pipe Collector tubes, 54 m2 gross area, 36 m2 net absorber area) installed at the top of the hot water recirculation loop in the Social Security Mid-Atlantic Center in Philadelphia. Water returning to the hot water storage tank is heated by the solar array when solar energy is available. This new approach, as opposed to the more conventional approach of preheating incoming water, is made possible by the thermal diode effect of heat pipes and low heat loss from evacuated tube solar collectors. The simplicity of this approach and its low installation costs makes the deployment of solar energy in existing commercial buildings more attractive, especially where the roof is far removed from the water heating system, which is often in the basement. Initial observed performance of the system is reported. Hourly simulation estimates annual energy delivery of 111 GJ/year of solar heat and that the annual efficiency (based on the 54 m2 gross area) of the solar collectors is 41%, and that of the entire system including parasitic pump power, heat loss due to freeze protection, and heat loss from connecting piping is 34%. Annual average collector efficiency based on a net aperture area of 36 m2 is 61.5% according to the hourly simulation.

scholarly journals Design of an IoT based Real Time Environment Monitoring System using Legacy Sensors

2018 ◽  
Vol 210 ◽  
pp. 03008
Author(s):  
Aparajita Das ◽  
Manash Pratim Sarma ◽  
Kandarpa Kumar Sarma ◽  
Nikos Mastorakis
Keyword(s):  
Air Pollution ◽  
Light Intensity ◽  
Real Time ◽  
Environmental Conditions ◽  
Low Cost ◽  
Environment Monitoring ◽  
Time Data ◽  
Graphical Information ◽  
Real Time Data ◽  
Sun Light

This paper describes the design of an operative prototype based on Internet of Things (IoT) concepts for real time monitoring of various environmental conditions using certain commonly available and low cost sensors. The various environmental conditions such as temperature, humidity, air pollution, sun light intensity and rain are continuously monitored, processed and controlled by an Arduino Uno microcontroller board with the help of several sensors. Captured data are broadcasted through internet with an ESP8266 Wi-Fi module. The projected system delivers sensors data to an API called ThingSpeak over an HTTP protocol and allows storing of data. The proposed system works well and it shows reliability. The prototype has been used to monitor and analyse real time data using graphical information of the environment.

Real Time Experimental Performance Assessment of a Photovoltaic Thermal System Cascaded with Flat Plate and Heat Pipe Evacuated Tube Collector

2021 ◽  
pp. 1-28
Author(s):  
Laveet Kumar ◽  
Md Hasanuzzaman ◽  
Nasrudin Abd Rahim
Keyword(s):  
Performance Assessment ◽  
Flat Plate ◽  
Heat Pipe ◽  
Large Scale ◽  
Industrial Process ◽  
Simulation Models ◽  
Solar Thermal ◽  
Evacuated Tube Collector ◽  
Flat Plate Collector ◽  
Evacuated Tube

Abstract In response to the global quest for a sustainable and environmentally friendly source of energy most scientists' discretion is solar energy, especially solar thermal. However, successful deployment of solar thermal technologies such as solar assisted process heating (SAPH) systems in medium- to large-scale industries is still in quandary due to their inefficacy in raising ample temperatures. Cascaded SAPH system, which is essentially a series combination of two same or different types of thermal collectors, may provide a worthwhile solution to this problem. In this article, performance assessment and comparison of two cascaded SAPH systems have been presented: photovoltaic thermal (PVT) cascaded with flat-plate collector (PVT-FPC) and PVT coupled with heat-pipe evacuated tube collector (PVT-HPETC). Simulation models have been presented for individual FPC, HPETC and PVT as well as PVT cascaded with FPC and HPETC systems in TRNSYS and validated through outdoor experimentation. Both the first and the second laws of thermodynamics have been employed to reveal veritable performance of the systems. Results show that PVT-HPETC delivers better performance with 1625 W thermal energy, 81% energy efficiency and 13.22% exergy efficiency. It cuts 1.37 kg of CO2 on an hourly basis. Cascaded systems can be effective in sustaining industrial process heat requirements.

Sign in / Sign up

Export Citation Format

Share Document