Effects of Fiber Content and Water Ratio on the Strength of Fiber Reinforced Mortar

2012 ◽  
Vol 204-208 ◽  
pp. 3961-3964
Author(s):  
Yao Wang ◽  
Wei Hong Xuan ◽  
Yu Zhi Chen ◽  
Xiao Hong Chen ◽  
Gang Zheng
Keyword(s):  
Flexural Strength ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Polypropylene Fiber ◽  
Fiber Content ◽  
Early Age ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Cement Material ◽  
Water Ratio

The compressive and flexural strength of ordinary mortar and fiber reinforced mortar with five different pp fiber content were tested in this paper. The results show that the compressive strength reduced gradually with PP fiber increasing, and the flexural strength increased when the fiber volume fraction is no more than 0.12%. The higher water ratio can weaken the cohesiveness of the fiber and cement material, and the influence of polypropylene fiber on the flexural strength of mortar decreased after soaking. The major strength damage in the process of curing is caused in the early age and appropriate amount of fiber is beneficial to reduce strength damage.

Effect of Polypropylene Fiber on Strength and Flexural Properties of Concrete Containing Silica Fume

2011 ◽  
Vol 346 ◽  
pp. 30-33
Author(s):  
Hong Wei Wang
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Silica Fume ◽  
Modulus Of Elasticity ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Flexural Modulus ◽  
Polypropylene Fiber ◽  
Flexural Properties ◽  
Fiber Volume

A designed experimental study has been conducted to investigate the effect of polypropylene fiber on the compressive strength and flexural properties of concrete containing silica fume, a large number of experiments have been carried out in this study. The flexural properties include flexural strength and flexural modulus of elasticity. On the basis of the experimental results of the specimens of six sets of mix proportions, the mechanism of action of polypropylene fiber on compressive strength, flexural strength and flexural modulus of elasticity has been analyzed in details. The results indicate that there is a tendency of increase in the compressive strength and flexural strength, and the flexural modulus of elasticity of concrete containing silica fume decrease gradually with the increase of fiber volume fraction.

scholarly journals Surface Cracking and Fractal Characteristics of Bending Fractured Polypropylene Fiber-Reinforced Geopolymer Mortar

2021 ◽  
Vol 5 (4) ◽  
pp. 142
Author(s):  
Li Li ◽  
Hai-Xin Sun ◽  
Yang Zhang ◽  
Bo Yu
Keyword(s):  
Fractal Dimension ◽  
Crack Length ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Polypropylene Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Surface Cracking ◽  
Fractal Characteristics ◽  
Geopolymer Composites

Fiber is effective in restricting cracks and improving the toughness of geopolymer composites, but few studies have focused on the surface crack characteristics of fiber-reinforced geopolymer composites. In this paper, after flexural tests of polypropylene fiber-reinforced geopolymer mortar, the surface cracking image was collected by a digital camera and cracking information was extract by deep learning. Finally, the cracking and fractal characteristics were specifically discussed. The semantic segmentation network can accurately extract surface cracks for calculating various parameters. The results showed that the mean intersection over union (mIoU) and mean pixel accuracy (mPA) of the cracks are 0.8451 and 0.9213, respectively. Generally, the crack length, width, area, and fractal dimension of the specimen are all increased with the increase in the fiber volume fraction. These crack parameters grow rapidly when the fiber content is small, and the growth of the crack parameters gradually slows down as the fiber volume fraction increases to approximately 1.5%. The highest crack parameter values were found in the geopolymer mortar, with a 0.48 water–binder ratio and 12 mm fiber length. The variation of the bottom crack length and the side crack fractal dimension can be used to represent the overall crack variation patterns. Meanwhile, the crack parameters increase with the increased fiber factor in a quadratic function. Based on these crack parameters, the critical fiber factor and dense fiber factor of polypropylene fiber-reinforced geopolymer mortar were 200 and 550, respectively. They are greater than those of fiber-reinforced Portland cementitious composites. The influence of various crack parameters on the flexural strength is in the order of the crack area, width, length, and fractal dimension.

scholarly journals Investigation on the Mechanical Properties of Fiber Reinforced Recycled Concrete

2016 ◽  
Vol 2 (1) ◽  
pp. 13-22 ◽  
Author(s):  
Hasan Jalilifar ◽  
Fatholla Sajedi ◽  
Sadegh Kazemi
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Experimental Test ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Fiber Content ◽  
Recycled Concrete ◽  
Test Results ◽  
Fiber Volume ◽  
Flexural Toughness

The flexural strength of conventional concrete material is known to be enhanced by incorporating a moderate volume-fraction of randomly distributed fibers. However, there is limited information on describing the influence of fiber volume-fraction on the compressive and flexural strength of recycled coarse aggregate concrete (RCA-C) material. This paper reports on experimental test results of the RCA-C material replaced with 0, 30, 50 and 100% recycled aggregate and 0, 0.5, 1 and 1.5% steel fiber volume fraction. Three-point flexural tests of notched prism specimens were completed. The mechanical properties in compression were characterized using cube specimens. Significant improvement in compressive and flexural strength of RCA-C was found as fiber content increased from 0 to 1.5%. The experimental test results of RCA-C were further evaluated to investigate the influence of fiber content on flexural toughness. According to test results, the addition of steel fibers to RCA-C material appreciably increased the flexural toughness.

Optimization of Flexural Strength and Thermal Conductivity of Mortar Reinforced with Alfa Fibers

2015 ◽  
Vol 799-800 ◽  
pp. 794-799 ◽  
Author(s):  
Sebti Jaballi ◽  
Imed Miraoui ◽  
Hedi Hassis
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Flexural Strength ◽  
Fiber Volume Fraction ◽  
Bending Strength ◽  
Volume Fraction ◽  
Fiber Content ◽  
Fiber Volume ◽  
Degradation Of Mechanical Properties ◽  
Alfa Fibers

This paper focuses on the optimization of flexural strength and thermal conductivity of mortar reinforced with Alfa fibers. Fibers were manually extracted from Alfa leafs to avoid the risk of degradation of mechanical properties. A first group of samples (300 x 300 x 30 mm) having a fiber volume fraction of 0.5 to 1.5% is prepared to measure the thermal conductivity.The second composite family (40 x 40 x 160 mm) cured in a wet chamber is used for measuring its bending strength. The fiber percentage varies from 0.74 to 1,85%.The results show that the thermal conductivity decreases by increasing the fiber content. While the optimal percentage of fiber for the flexural strength is estimated at 1%, corresponding to an increase of 27% in strength.

scholarly journals Effect of SIFRCCs with Varying Steel Fiber Volume Fractions on Flexural Behavior

2020 ◽  
Vol 10 (6) ◽  
pp. 2072
Author(s):  
Seungwon Kim ◽  
Cheolwoo Park ◽  
Yongjae Kim
Keyword(s):  
Flexural Strength ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Flexural Behavior ◽  
Cementitious Composites ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Conventional Concrete ◽  
Volume Fractions ◽  
Fiber Reinforced Cementitious Composites

Conventional concrete is a brittle material with a very low tensile strength as a result of compressive strength and tensile strain. In this study, the flexural behavior characteristics of slurry-infiltrated fiber-reinforced cementitious composites (SIFRCCs) based on slurry-infiltrated fiber concrete (SIFCON), such as high-performance fiber-reinforced cementitious composites (HPFRCCs), were analyzed to maximize the fiber volume fraction and increase resistance to loads with very short working times (such as explosions or impacts). For extensive experimental variables, one fiber aspect ratio and three fiber volume fractions (6%, 5%, and 4%) were designed, and the flexural toughness and strength were figured out with respect to variables. A maximum flexural strength of 45 MPa was presented for a fiber volume fraction of 6%, and it was found that by increasing the fiber volume fraction the flexural strength and toughness increased. The test results with respect to fiber volume fraction revealed that after the initial crack, the load of SIFRCCs frequently increased because of the high fiber volume fraction. In addition to maximum strength, acceptable strength was found, which could have a positive effect on brittle fractures in structures where an accidental load is applied (such as an impact or explosion).

Monitoring of mechanical properties of prestressed glass fiber epoxy composites over 12 months after fabrication

2021 ◽  
pp. 002199832110047
Author(s):  
Mahmoud Mohamed ◽  
Siddhartha Brahma ◽  
Haibin Ning ◽  
Selvum Pillay
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Flexural Strength ◽  
Compressive Residual Stress ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Epoxy Composites ◽  
Flexural Properties ◽  
Initial Increase ◽  
Fiber Volume

Fiber prestressing during matrix curing can significantly improve the mechanical properties of fiber-reinforced polymer composites. One primary reason behind this improvement is the generated compressive residual stress within the cured matrix, which impedes cracks initiation and propagation. However, the prestressing force might diminish progressively with time due to the creep of the compressed matrix and the relaxation of the tensioned fiber. As a result, the initial compressive residual stress and the acquired improvement in mechanical properties are prone to decline over time. Therefore, it is necessary to evaluate the mechanical properties of the prestressed composites as time proceeds. This study monitors the change in the tensile and flexural properties of unidirectional prestressed glass fiber reinforced epoxy composites over a period of 12 months after manufacturing. The composites were prepared using three different fiber volume fractions 25%, 30%, and 40%. The results of mechanical testing showed that the prestressed composites acquired an initial increase up to 29% in the tensile properties and up to 32% in the flexural properties compared to the non-prestressed counterparts. Throughout the 12 months of study, the initial increase in both tensile and flexural strength showed a progressive reduction. The loss ratio of the initial increase was observed to be inversely proportional to the fiber volume fraction. For the prestressed composites fabricated with 25%, 30%, and 40% fiber volume fraction, the initial increase in tensile and flexural strength dropped by 29%, 25%, and 17%, respectively and by 34%, 26%, and 21%, respectively at the end of the study. Approximately 50% of the total loss took place over the first month after the manufacture, while after the sixth month, the reduction in mechanical properties became insignificant. Tensile modulus started to show a very slight reduction after the fourth/sixth month, while the flexural modulus reduction was observed from the beginning. Although the prestressed composites displayed time-dependent losses, their long-term mechanical properties still outperformed the non-prestressed counterparts.

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

Improved Early-Age Cohesive Stress Response from Hybrid Blends of Micro and Macro Fibers

2021 ◽  
Vol 1046 ◽  
pp. 1-7
Author(s):  
Manjunath V. Bhogone ◽  
Kolluru V.L. Subramaniam
Keyword(s):  
Reinforced Concrete ◽  
Stress Response ◽  
Volume Fraction ◽  
Polypropylene Fiber ◽  
Fiber Reinforced Concrete ◽  
Early Age ◽  
Fiber Reinforced ◽  
Cohesive Stress ◽  
Concrete Matrix ◽  
Polypropylene Fiber Reinforced Concrete

The fracture response of macro polypropylene fiber reinforced concrete (PPFRC) and hybrid blend of macro and micro polypropylene fiber reinforced concrete (HyFRC) are evaluated at 1, 3, 7 and 28 days. There is an improvement in the early-age fracture response of HyFRC compared to PPFRC. The changing cohesive stress-crack separation relationship produced by ageing of the concrete matrix is determined from the fracture test responses. An improved early-age cohesive stress response is obtained from the hybrid blend containing micro and macro fibers. The hybrid fiber blend also has a higher tensile strength at early age when compared to an identical volume fraction of macro polypropylene fibers.

scholarly journals Influence of the Fiber Volume Content on the Durability-Related Properties of Polypropylene-Fiber-Reinforced Concrete

2020 ◽  
Vol 12 (2) ◽  
pp. 549
Author(s):  
Chenfei Wang ◽  
Zixiong Guo ◽  
Ditao Niu
Keyword(s):  
Reinforced Concrete ◽  
Flexural Strength ◽  
Volume Content ◽  
Polypropylene Fiber ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Freeze Thaw ◽  
Chloride Environment ◽  
Polypropylene Fiber Reinforced Concrete

Polypropylene-fiber-reinforced concrete impacts the early shrinkage during the plastic stage of concrete, and the fiber volume content influences the durability-related properties of concrete. The purpose of this paper was to investigate the influence of fiber volume content on the mechanical properties, durability, and chloride ion penetration of polypropylene-fiber-reinforced concrete in a chloride environment. Tests were carried out on cubes and cylinders of polypropylene-fiber-reinforced concrete with polypropylene fiber contents ranging from 0% to 0.5%. Extensive data from flexural strength testing, dry–wet testing, deicer frost testing, and chloride penetration testing were recorded and analyzed. The test results show that the addition of the fiber improves the failure form of the concrete specimens, and 0.1% fiber content maximizes the compactness of the concrete. The flexural strength of specimen C2 with 0.1% fiber shows the highest strength obtained herein after freeze–thaw cycling, and the water absorption of specimen C2 is also the lowest after dry–wet cycling. The results also indicate that increasing the fiber volume content improves the freeze–thaw resistance of the concrete in a chloride environment. Chlorine ions migrate with the moisture during dry–wet and freeze–thaw cycling. The chlorine ion diffusion coefficient (Dcl) increases with increasing fiber content, except for that of specimen C2 in a chloride environment. The Dcl during freeze–thaw cycling is much higher than that during dry–wet cycling.

Sign in / Sign up

Export Citation Format

Share Document