Effect of Fenton Reagent on the Thermal Stability of Proton-Exchange Membrane for Fuel Cell

2012 ◽  
Vol 217-219 ◽  
pp. 780-784
Author(s):  
Yi Heng Lu ◽  
Feng Wei ◽  
Wei Long Liu
Keyword(s):  
Thermal Stability ◽  
Thermal Degradation ◽  
Proton Exchange Membrane ◽  
Degradation Kinetics ◽  
Proton Exchange ◽  
Thermal Degradation Kinetics ◽  
Fenton Reagent ◽  
Exponential Factor ◽  
Average Value ◽  
Exchange Membrane

The thermal stability and thermal degradation kinetics of proton-exchange membrane were investigated, as the membrane reacted with Fenton reagent at 80°C. Non-isothermal kinetic data of the membrane were analyzed by using the thermo-gravimetry analysis and the Kissinger、Flynn-Wall-Ozawa and Friedman methods under the conditions of flowing gas nitrogen and the heating rate of 5、10 and 20°C/min. The minimum temperature of the thermal degradation is greater than 360.8°C in the conversion rate of 10%. The thermal decomposition process occurred one step. The average value of apparent activation energy is 245.48kJ/mol, pre-exponential factor is 2.52×1018 min-1, the reaction mechanism is controlled by D4.

Thermal degradation kinetics of Opuntia Ficus Indica flour and talc-filled poly (lactic acid) hybrid biocomposites by TGA analysis

2021 ◽  
pp. 002199832110082
Author(s):  
Azzeddine Gharsallah ◽  
Abdelheq Layachi ◽  
Ali Louaer ◽  
Hamid Satha
Keyword(s):  
Thermal Stability ◽  
Lactic Acid ◽  
Thermal Degradation ◽  
Degradation Kinetics ◽  
Degradation Mechanism ◽  
Melt Processing ◽  
Thermal Degradation Kinetics ◽  
Poly Lactic Acid ◽  
Opuntia Ficus Indica ◽  
Model Free

This paper reports the effect of lignocellulosic flour and talc powder on the thermal degradation behavior of poly (lactic acid) (PLA) by thermogravimetric analysis (TGA). Lignocellulosic flour was obtained by grinding Opuntia Ficus Indica cladodes. PLA/talc/ Opuntia Ficus Indica flour (OFI-F) biocomposites were prepared by melt processing and characterized using Wide-angle X-ray scattering (WAXS) and Scanning Electron Microscope (SEM). The thermal degradation of neat PLA and its biocomposites can be identified quantitatively by solid-state kinetics models. Thermal degradation results on biocomposites compared to neat PLA show that talc particles at 10 wt % into the PLA matrix have a minor impact on the thermal stability of biocomposites. Loading OFI-F and Talc/OFI-F mixture into the PLA matrix results in a decrease in the maximum degradation temperature, which means that the biocomposites have lower thermal stability. The activation energies (Ea) calculated by the Flynn Wall Ozawa (FWO) and Kissinger Akahira Sunose (KAS) model-free approaches and by model-fitting (Kissinger method and Coats-Redfern method) are in good agreement with one another. In addition, in this work, the degradation mechanism of biocomposites is proposed using Coats-Redfern and Criado methods.

scholarly journals Thermal Degradation Kinetics and Modeling Study of Ultra High Molecular Weight Polyethylene (UHMWP)/Graphene Nanocomposite

Molecules ◽  
2021 ◽  
Vol 26 (6) ◽  
pp. 1597
Author(s):  
Iman Jafari ◽  
Mohamadreza Shakiba ◽  
Fatemeh Khosravi ◽  
Seeram Ramakrishna ◽  
Ehsan Abasi ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Molecular Weight ◽  
Thermal Degradation ◽  
High Molecular Weight ◽  
Degradation Kinetics ◽  
Graphene Nanosheets ◽  
Thermal Degradation Kinetics ◽  
Graphene Nanocomposites ◽  
Kinetics Of ◽  
Ultra High Molecular Weight

The incorporation of nanofillers such as graphene into polymers has shown significant improvements in mechanical characteristics, thermal stability, and conductivity of resulting polymeric nanocomposites. To this aim, the influence of incorporation of graphene nanosheets into ultra-high molecular weight polyethylene (UHMWPE) on the thermal behavior and degradation kinetics of UHMWPE/graphene nanocomposites was investigated. Scanning electron microscopy (SEM) analysis revealed that graphene nanosheets were uniformly spread throughout the UHMWPE’s molecular chains. X-Ray Diffraction (XRD) data posited that the morphology of dispersed graphene sheets in UHMWPE was exfoliated. Non-isothermal differential scanning calorimetry (DSC) studies identified a more pronounced increase in melting temperatures and latent heat of fusions in nanocomposites compared to UHMWPE at lower concentrations of graphene. Thermogravimetric analysis (TGA) and derivative thermogravimetric (DTG) revealed that UHMWPE’s thermal stability has been improved via incorporating graphene nanosheets. Further, degradation kinetics of neat polymer and nanocomposites have been modeled using equations such as Friedman, Ozawa–Flynn–Wall (OFW), Kissinger, and Augis and Bennett’s. The "Model-Fitting Method” showed that the auto-catalytic nth-order mechanism provided a highly consistent and appropriate fit to describe the degradation mechanism of UHMWPE and its graphene nanocomposites. In addition, the calculated activation energy (Ea) of thermal degradation was enhanced by an increase in graphene concentration up to 2.1 wt.%, followed by a decrease in higher graphene content.

Thermal Stabilities and the Thermal Degradation Kinetics Study of the Flame Retardant Epoxy Resins

2014 ◽  
Vol 1053 ◽  
pp. 263-267 ◽  
Author(s):  
Xiu Juan Tian
Keyword(s):  
Thermal Stability ◽  
Thermal Degradation ◽  
Flame Retardant ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Degradation Kinetics ◽  
Thermal Degradation Kinetics ◽  
Thermal Stabilities ◽  
Degradation Kinetic ◽  
Modified Epoxy

Thermal stability and thermal degradation kinetics of epoxy resins with 2-(Diphenylphosphinyl)-1, 4-benzenediol were investegated by thermogravimetric analysis (TGA) at different heating rates of 5 K/min, 10 K/min, 20 K/min and 40 K/min. The thermal degradation kinetic mechanism and models of the modified epoxy resins were determined by Coast Redfern method.The results showed that epoxy resins modified with the flame retardant had more thermal stability than pure epoxy resin. The solid-state decomposition mechanism of epoxy resin and the modified epoxy resin corresponded to the controlled decelerating ځ˽̈́˰̵̳͂͆ͅ˼˰̴̱̾˰̸̵̈́˰̵̸̳̱̹̽̾̓̽˰̶̳̹̾̈́̿̾̓ͅ˰̶˸ځ˹˰̵̵͇͂˰̃˸́˽ځ˹2/3. The introduction of phosphorus-containing flame retardant reduced thermal degradation rate of epoxy resins in the primary stage, and promote the formation of carbon layer.

Novel Proton Exchange Membrane for High Temperature Fuel Cells

1997 ◽  
Vol 496 ◽  
Author(s):  
M. Bhamidipati ◽  
E. Lazaro ◽  
F. Lyons ◽  
R. S. Morris
Keyword(s):  
Thermal Stability ◽  
Fuel Cells ◽  
High Temperature ◽  
Electrochemical Performance ◽  
Proton Exchange Membrane ◽  
Research Effort ◽  
Analysis Data ◽  
Proton Exchange ◽  
Temperature Conductivity ◽  
Exchange Membrane

ABSTRACTThis research effort sought to demonstrate that combining select phosphonic acid additives with Nafion could improve Nafion's high temperature electrochemical performance. A 1:1 mixture of the additive with Nafion, resulted in a film that demonstrated 30% higher conductivity than a phosphoric acid equilibrated Nafion control at 175°C. This improvement to the high temperature conductivity of the proton exchange membrane Nafion is without precedent. In addition, thermal analysis data of the test films suggested that the additives did not compromise the thermal stability of Nafion. The results suggest that the improved Nafion proton exchange membranes could offer superior electrochemical performance, but would retain the same degree of thermal stability as Nafion. This research could eventually lead to portable fuel cells that could oxidize unrefined hydrocarbon fuels, resulting in wider proliferation of fuel cells for portable power.

Thermo-oxidative and thermal degradation kinetics of silica/polymethyl methacrylate composites with electrostatic interaction phase interfaces

2019 ◽  
Vol 39 (2) ◽  
pp. 105-116 ◽  
Author(s):  
Hongyan Li ◽  
Yongqiang Fu ◽  
Hongli Liu ◽  
Cong Sun ◽  
Ruyi Li ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Thermal Degradation ◽  
Polymethyl Methacrylate ◽  
Electrostatic Interaction ◽  
Degradation Kinetics ◽  
Thermal Degradation Kinetics ◽  
Degradation Kinetic ◽  
Further Development ◽  
Kinetics Of ◽  
Insulation Performance

AbstractThe thermo-oxidative and thermal degradation kinetic parameters of polymethyl methacrylate-methacryloxyethyltrimethyl ammonium chloride/silica aerogel composites (PMMA-MTC/SA) were investigated in this paper and were compared with the thermal stability and thermal conductivity of different types of composites. As a composite with electrostatic interaction, the thermo-oxidative and thermal degradation activation energies (E) of PMMA-MTC/SA were 173.97 and 188.05 kJ/mol, respectively. The results indicated that the electrostatic interaction could indeed enhance the thermal stability of silica/polymethyl methacrylate composites on the premise of good mechanical properties and heat insulation performance. It is of great significance for the further development of silica-based thermal insulation composites.

Non-isothermal crystallization and thermal degradation kinetics of MXene/linear low-density polyethylene nanocomposites

e-Polymers ◽  
2017 ◽  
Vol 17 (5) ◽  
pp. 373-381 ◽  
Author(s):  
Xinxin Cao ◽  
Mengqi Wu ◽  
Aiguo Zhou ◽  
You Wang ◽  
Xiaofang He ◽  
...  
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Thermal Degradation ◽  
Isothermal Crystallization ◽  
Degradation Kinetics ◽  
Thermal Degradation Kinetics ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Kinetics Of

AbstractA novel two-dimensional material MXene was used to synthesize nanocomposites with linear low-density polyethylene (LLDPE). The influence of MXene on crystallization and thermal degradation kinetics of LLDPE was investigated. Non-isothermal crystallization kinetics was investigated by using differential scanning calorimetry (DSC). The experimental data was analyzed by Jeziorny theory and the Mo method. It is found that MXene acted as a nucleating agent during the non-isothermal crystallization process, and 2 wt% MXene incorporated in the nanocomposites could accelerate the crystallization rate. Findings from activation energy calculation for non-isothermal crystallization came to the same conclusion. Thermal gravity (TG) analysis of MXene/LLDPE nanocomposites was conducted at different heating rates, and the TG thermograms suggested the nanocomposites showed an improvement in thermal stability. Apparent activation energy (Ea) of thermal degradation was calculated by the Kissinger method, and Ea values of nanocomposites were higher than that of pure LLDPE. The existence of MXene seems to lead to better thermal stability in composites.

Thermal properties and thermal degradation kinetics of phenolic and wood flour-reinforced phenolic foams

2016 ◽  
Vol 51 (1) ◽  
pp. 125-138 ◽  
Author(s):  
JC Domínguez ◽  
B del Saz-Orozco ◽  
M Oliet ◽  
MV Alonso ◽  
F Rodriguez
Keyword(s):  
Thermal Stability ◽  
Thermal Degradation ◽  
Degradation Kinetics ◽  
Wood Flour ◽  
Activation Energies ◽  
Thermal Degradation Kinetics ◽  
Kinetic Methods ◽  
Model Free ◽  
Phenolic Foam ◽  
Kinetics Of

In the present work, the thermal stability, changes in chemical structure during thermal degradation, and the kinetics of thermal degradation of a phenolic foam were studied. An 8.5 wt% of Pinus radiata wood flour reinforcement was added to the phenolic foam. A commercial phenolic resol was used as the matrix for the foam. The wood flour-reinforced foam showed a structure similar to the phenolic foam according to the Fourier transform infrared spectroscopy results. The wood flour increased the thermal stability of the phenolic foam in the first stage of thermal degradation ( T 5%), decreased it in the second step ( T 25%), and negligibly influenced the final stage. The activation energies of the degradation processes of the studied materials were obtained by the Kissinger-Akahira-Sunose and Flynn-Wall-Ozawa model-free kinetic methods and a 2-Gaussian distributed activation energy model. The values of the activation energies obtained by the model-free kinetic methods for the first degradation stage of the phenolic foams were in a range between 110 and 170 kJ mol−1, whereas for the wood flour it was 162 kJ mol−1 for almost all of the conversion range of its main degradation stage. The applied models showed good fits for all the materials, and the activation energies calculated were in agreement with the values found in the literature.

Sign in / Sign up

Export Citation Format

Share Document