Research of Elastic Deformation of Rubber Ink Roller and Ink Flow Characteristics on Two Ink Rollers

2012 ◽  
Vol 220-223 ◽  
pp. 1703-1710
Author(s):  
Lei Su ◽  
Hong Yan Chu ◽  
Li Gang Cai ◽  
Jun Tao Zhao
Keyword(s):  
Theoretical Analysis ◽  
Flow Field ◽  
Layer Thickness ◽  
Elastic Deformation ◽  
Flow Characteristics ◽  
Rotation Velocity ◽  
Offset Printing ◽  
Rubber Roller

In order to improve the quality of colorful offset printing and know the process of ink transferring, this paper adopts the method of theoretical analysis and experiment, the velocity and pressure of the ink flow field are analyzed when the rubber roller deforms and the two rollers rotate, and the effective ink layer thickness is extracted, then the ink transferring rate can be got. The rubber roller’s deformation and ink transferring rate under different conditions are got, and factors, such as rotation velocity, deformation of rubber roller, ink layer thickness between two rollers, which affect the ink flow and transferring rate are analyzed.

Numerical Simulation of Quenchant Flow Characteristics in Large Quench Tank

2012 ◽  
Vol 271-272 ◽  
pp. 1372-1376
Author(s):  
Hui Sun
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Flow Field ◽  
Flow Rate ◽  
Inner Core ◽  
Flow Characteristics ◽  
Structure Design ◽  
Inner Surface ◽  
Computational Fluid Dynamics Cfd

The computational fluid dynamics (CFD) technique is employed to predict the flow of quenchant in a large quench tank. The characteristics of flow field in the existing quench tank are investigated, and the major deficiency occurred in the tank structure design is analyzed. Two different schemes for improving the tank structure design are brought forward, and further numerical simulations are carried out. Results show that the non-uniform flow field is generated throughout the quenching zone in the existing large quench tank. There is clear difference in flow rate in the regions near the inner surface of workpiece and the outer, which may cause the workpiece distortion and even cracking. Reduction in ring pipe intermediate diameter can not obviously enhance the uniformity of flow field in the quench tank. By adding an inner core in the center zone of the tank, the flow rate in the region near the inner surface of workpiece can be increased effectively, and the flow rate difference found in the quenching zone reduced significantly, which are beneficial to guarantee the quenching quality of workpiece.

Structure and Orientation of As Precipitates in LT-MBE Grown GaAs

1991 ◽  
Vol 49 ◽  
pp. 900-901 ◽  
Author(s):  
Alain Claverie ◽  
Zuzanna Liliental-Weber
Keyword(s):  
Transport Properties ◽  
Layer Thickness ◽  
Growth Temperature ◽  
Low Temperatures ◽  
Lattice Parameter ◽  
Crystalline Quality ◽  
Insulating Properties ◽  
Lt Gaas

GaAs layers grown by MBE at low temperatures (in the 200°C range, LT-GaAs) have been reported to have very interesting electronic and transport properties. Previous studies have shown that, before annealing, the crystalline quality of the layers is related to the growth temperature. Lowering the temperature or increasing the layer thickness generally results in some columnar polycrystalline growth. For the best “temperature-thickness” combinations, the layers may be very As rich (up to 1.25%) resulting in an up to 0.15% increase of the lattice parameter, consistent with the excess As. Only after annealing are the technologically important semi-insulating properties of these layers observed. When annealed in As atmosphere at about 600°C a decrease of the lattice parameter to the substrate value is observed. TEM studies show formation of precipitates which are supposed to be As related since the average As concentration remains almost unchanged upon annealing.

An experimental and theoretical study of the abrasion performance of digital light processing parts

2020 ◽  
pp. 095440542098133
Author(s):  
Mehdi Kazemi ◽  
Abdolreza Rahimi
Keyword(s):  
Layer Thickness ◽  
Normal Load ◽  
Digital Light Processing ◽  
One Step ◽  
Pin On Disk ◽  
The Relationship ◽  
Influential Parameters ◽  
Disk Method ◽  
Normal Angle

Generally, interactions at surface asperities are the cause of wear. Two-Thirds of wear in industry occurs because of the abrasive or adhesive mechanisms. This research presents an analytical model for abrasion of additive manufactured Digital Light Processing products using pin-on-disk method. Particularly, the relationship between abrasion volume, normal load, and surface asperities’ angle is investigated. To verify the proposed mathematical model, the results of this model are verified with the practical experiments. Results show that the most influential parameters on abrasion rate are normal load and surface’s normal angle. Abrasion value increases linearly with increasing normal load. The maximum abrasion value occurs when the surface’s normal angle during fabrication is 45°. After the asperities are worn the abrasion volume is the same for all specimens with different surface’s normal angle. Though layer thickness does not directly affect the wear rate, but surface roughness tests show that layer thickness has a great impact on the quality of the abraded surface. When the thickness of the layers is high, the abraded surface has deeper valleys, and thus has a more negative skewness. This paper presents an original approach in abrasion behavior improvement of DLP parts which no research has been done on it so far; thus, bringing the AM one step closer to maturity.

scholarly journals Investigation of the Heteroepitaxial Process Optimization of Ge Layers on Si (001) by RPCVD

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 928
Author(s):  
Yong Du ◽  
Zhenzhen Kong ◽  
Muhammet Toprak ◽  
Guilei Wang ◽  
Yuanhao Miao ◽  
...  
Keyword(s):  
High Temperature ◽  
Buffer Layer ◽  
Layer Thickness ◽  
Growth Temperature ◽  
Crystalline Quality ◽  
Initial Growth ◽  
Two Dimensional ◽  
High Quality ◽  
Reduced Pressure

This work presents the growth of high-quality Ge epilayers on Si (001) substrates using a reduced pressure chemical vapor deposition (RPCVD) chamber. Based on the initial nucleation, a low temperature high temperature (LT-HT) two-step approach, we systematically investigate the nucleation time and surface topography, influence of a LT-Ge buffer layer thickness, a HT-Ge growth temperature, layer thickness, and high temperature thermal treatment on the morphological and crystalline quality of the Ge epilayers. It is also a unique study in the initial growth of Ge epitaxy; the start point of the experiments includes Stranski–Krastanov mode in which the Ge wet layer is initially formed and later the growth is developed to form nuclides. Afterwards, a two-dimensional Ge layer is formed from the coalescing of the nuclides. The evolution of the strain from the beginning stage of the growth up to the full Ge layer has been investigated. Material characterization results show that Ge epilayer with 400 nm LT-Ge buffer layer features at least the root mean square (RMS) value and it’s threading dislocation density (TDD) decreases by a factor of 2. In view of the 400 nm LT-Ge buffer layer, the 1000 nm Ge epilayer with HT-Ge growth temperature of 650 °C showed the best material quality, which is conducive to the merging of the crystals into a connected structure eventually forming a continuous and two-dimensional film. After increasing the thickness of Ge layer from 900 nm to 2000 nm, Ge surface roughness decreased first and then increased slowly (the RMS value for 1400 nm Ge layer was 0.81 nm). Finally, a high-temperature annealing process was carried out and high-quality Ge layer was obtained (TDD=2.78 × 107 cm−2). In addition, room temperature strong photoluminescence (PL) peak intensity and narrow full width at half maximum (11 meV) spectra further confirm the high crystalline quality of the Ge layer manufactured by this optimized process. This work highlights the inducing, increasing, and relaxing of the strain in the Ge buffer and the signature of the defect formation.

EFFECTS OF BOUNDARY-LAYER THICKNESS ON UNSTEADY FLOW CHARACTERISTICS INSIDE OPEN CAVITIES AT SUBSONIC AND TRANSONIC SPEEDS

2012 ◽  
Vol 19 ◽  
pp. 206-213
Author(s):  
DANG-GUO YANG ◽  
JIAN-QIANG LI ◽  
ZHAO-LIN FAN ◽  
XIN-FU LUO
Keyword(s):  
Boundary Layer ◽  
Unsteady Flow ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Sound Pressure ◽  
Flow Characteristics ◽  
Open Cavity ◽  
Aerodynamic Noise ◽  
Sustained Oscillation ◽  
Cavity Depth

An experimental study was conducted in a 0.6m by 0.6m wind-tunnel to analyze effects of boundary-layer thickness on unsteady flow characteristics inside a rectangular open cavity at subsonic and transonic speeds. The sound pressure level (SPL) distributions at the centerline of the cavity floor and Sound pressure frequency spectrum (SPFS) characteristics on some measurement positions presented herein was obtained with cavity length-to-depth ratio (L/D) of 8 over Mach numbers (Ma) of 0.6 and 1.2 at a Reynolds numbers (Re) of 1.23 × 107 and 2.02 × 107 per meter under different boundary-layer thickness to cavity-depth ratios (δ/D). The experimental angle of attack, yawing and rolling angles were 0°. The results indicate that decrease in δ/D leads to severe flow separation and unsteady pressure fluctuation, which induces increase in SPL at same measurement points inside the cavity at Ma of 0.6. At Ma of 1.2, decrease in δ/D results in enhancing compressible waves. Generally, decrease in δ/D induces more flow self-sustained oscillation frequencies. It also makes severer aerodynamic noise inside the open cavity.

Thermo-flow characteristics and air flow field leading of the air-cooled condenser cell in a power plant

2011 ◽  
Vol 54 (9) ◽  
pp. 2475-2482 ◽  
Author(s):  
WanXi Zhang ◽  
LiJun Yang ◽  
XiaoZe Du ◽  
YongPing Yang
Keyword(s):  
Power Plant ◽  
Flow Field ◽  
Air Flow ◽  
Flow Characteristics

scholarly journals Study on the 3D Hydrodynamic Characteristics and Velocity Uniformity of a Gravity Flow Circular Flume

Water ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 927
Author(s):  
Yi Zhang ◽  
Longxi Han ◽  
Lina Chen ◽  
Chenfang Wang ◽  
Bo Chen ◽  
...  
Keyword(s):  
Flow Field ◽  
Environmental Science ◽  
Structural Characteristics ◽  
Longitudinal Velocity ◽  
Flow Characteristics ◽  
Science Research ◽  
Hydrodynamic Characteristics ◽  
Straight Channel ◽  
Uniformity Coefficient ◽  
Annular Flume

Flumes have been widely used in water conservancy science and environmental science research. It is of great significance to obtain the hydrodynamic characteristics and flow field uniformity in the flume. In this study, a new type of annular flume was taken as an example. The 3D flow field was simulated by using a commercial computational fluid dynamics (CFD) code, and was also measured by acoustic doppler velocimeter (ADV) to verify the simulation results. The average relative error range was between 8.37% and 9.95%, the simulated results basically reflected the actual situation of the flow field. On this basis, the structural characteristics of flow field were analyzed. A new calculation method of flow velocity uniformity was presented according to the flow characteristics of natural open channels. The velocity uniformity in the straight channel was calculated and analyzed based on this method, and the influence of speed on the velocity uniformity was further discussed. The length of uniform section was negatively correlated with the rotational speed (average velocity), which was between 39 cm and 101 cm in the straight, and the uniformity coefficient was less than 10%. Finally, the water flow characteristics in the straight channel without wheel were compared with the natural open channel flow. The longitudinal velocity was well fitted with the Prandtl logarithmic distribution formula (R2 > 0.977), and the application feasibility of the flume was analyzed. This study can provide technical support for the development and application of annular flume.

Effects of U-Shape Inner Cooler on Flow and Solidification of Molten Steel in Slab Continuous Casting Mold

2011 ◽  
Vol 291-294 ◽  
pp. 423-427
Author(s):  
Yan Juan Jin ◽  
Xiao Chao Cui ◽  
Zhu Zhang
Keyword(s):  
Fluid Dynamics ◽  
Temperature Field ◽  
Flow Field ◽  
Continuous Casting ◽  
Molten Steel ◽  
Continuous Casting Mold ◽  
Slab Continuous Casting ◽  
Cooling Technology ◽  
Steel Flow

An inner-outer coupled cooling technology of molten steel for 1240×200mm slab continuous casting, that is to set an inner cooler—U shape pipes in the mold, is put forward in order to enhance the efficiency of transmitting heat and improve inner structure of billet. The flow status and solidification status of molten steel under coupling flow field and temperature field in inner-outer coupled cooling mold are simulated by using fluid dynamics software, and compare with those in traditional mold. It is found that setting inner cooler in the mold can make molten steel flow status even, which is favorable to floating up of the inclusion, quickening the solidification of steel liquid and improving the quality of billet.

Sign in / Sign up

Export Citation Format

Share Document