Discharge Flow Ripple of Axial Piston Pump with Conical Cylinder Block

2010 ◽  
Vol 34-35 ◽  
pp. 440-445
Author(s):  
Lei Li ◽  
Jian Ke ◽  
Jia Xu ◽  
Wang Yong
Keyword(s):  
Block Design ◽  
Cone Angle ◽  
Point Of View ◽  
Piston Pump ◽  
Cylinder Block ◽  
Axial Piston Pump ◽  
Discharge Flow ◽  
Flow Ripple ◽  
Displacement Pump ◽  
Axial Piston

The discharge flow ripple is a crucial criterion for evaluating the piston pump. This research examines the discharge flow ripple of axial piston pump with conical cylinder block by developing a comprehensive mathematical model based upon the Bernoulli equation and the continuity equation. The novel aspect of this research is that it includes the analysis of cylinder block cone angle. From the results of this research, it can be concluded that cylinder block cone angle has a significant impact on the discharge flow ripple, and utilizing a conical cylinder block design is more feasible than cylindrical cylinder block from a flow ripple point of view. This conclusion can be used to guide the up-front design for the variable displacement pump.

Flow Characteristic of Axial Piston Pump with Conical Cylinder Block

2010 ◽  
Vol 42 ◽  
pp. 43-47 ◽  
Author(s):  
Lei Li ◽  
Ming Heng Xu ◽  
Jian Ke ◽  
Lan Ying Yu
Keyword(s):  
Flow Characteristic ◽  
Characteristic Point ◽  
Block Design ◽  
Cone Angle ◽  
Simulation Software ◽  
Piston Pump ◽  
Cylinder Block ◽  
Parameter Method ◽  
Axial Piston Pump ◽  
Axial Piston

To examine the flow characteristic of axial piston pump with conical cylinder block, a comprehensive mathematical model of flow condition within a single cylinder bore was developed by utilizing discrete approximation. Each step of the discrete analog was fallen into three successive phases with oil compressibility and classical orifice equation. Besides, the discharge flow equation of whole pump was obtained with lumped parameter method. Based upon this model, a simulation system was built in the simulation software. The novel aspect of this research is that analysis of cylinder block cone angle. From the result of numerical simulation, it can be concluded that cylinder block cone angle has a significant impact on the flow characteristics, and conical cylinder block design is more feasible than cylindrical cylinder block from a flow characteristic point of view.

scholarly journals Flow Ripple Reduction of Axial-Piston Pump by Structure Optimizing of Outlet Triangular Damping Groove

Processes ◽  
2020 ◽  
Vol 8 (12) ◽  
pp. 1664
Author(s):  
Haocen Hong ◽  
Chunxiao Zhao ◽  
Bin Zhang ◽  
Dapeng Bai ◽  
Huayong Yang
Keyword(s):  
Numerical Models ◽  
Structural Parameters ◽  
Piston Pump ◽  
Axial Piston Pump ◽  
Discharge Flow ◽  
Flow Ripple ◽  
Ripple Reduction ◽  
Simulation Results ◽  
The Time Domain ◽  
Axial Piston

The triangular damping groove on the valve plate can effectively reduce the discharge flow ripple of an axial piston pump, which structural parameters will directly affect the pump’s dynamic characteristics. Herein, a multi-parameter data-based structure optimizing method of the triangular damping groove is investigated using numerical models and simulation results. The mathematical models of a nine-piston pump are proposed and developed by MATLAB/Simulink, and the simulation results are verified by experimental results. Then, the effects of width angle and depth angle on discharge flow are analyzed. Based on the analysis of groove parameters, an optimizing index, which considering the time domain characteristics of discharge flow, is proposed. As results show, comparing with the initial specific groove structure, the amplitude of flow ripple is reduced from 14.6% to 9.8% with the optimized structure. The results demonstrate that the outlet flow ripple can be significantly reduced by the optimized structure, and the proposed multi-parameter optimizing method can play a guiding significance in the design of low-ripple axial piston pumps.

scholarly journals Novel design of hydrodynamic–magnetic compound support for cylinder block–valve plate in axial piston pump

AIP Advances ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 115221
Author(s):  
Jihai Jiang ◽  
Boran Du ◽  
Jian Zhang ◽  
Geqiang Li
Keyword(s):  
Valve Plate ◽  
Piston Pump ◽  
Cylinder Block ◽  
Axial Piston Pump ◽  
Axial Piston ◽  
Novel Design

A Fast and Effective Method for the Optimization of the Valve Plate of Swashplate Axial Piston Pumps

2021 ◽  
Author(s):  
Gianluca Marinaro ◽  
Emma Frosina ◽  
Kim Stelson ◽  
Adolfo Senatore
Keyword(s):  
Numerical Model ◽  
Dynamic Pressure ◽  
Valve Plate ◽  
Lumped Parameter Model ◽  
Piston Pump ◽  
Axial Piston Pump ◽  
Flow Ripple ◽  
Lumped Parameter ◽  
Pressure Ripple ◽  
Axial Piston

Abstract This research presents a lumped parameter numerical model aimed at designing and optimizing an axial piston pump. For the first time, it has been shown that a lumped parameter model can accurately model axial piston pump dynamics based on a comparison with CFD models and experimental results. Since the method is much more efficient than CFD, it can optimize the design. Both steady-state and dynamic behaviors have been analyzed. The model results have been compared with experimental data, showing a good capacity in predicting the pump performance, including pressure ripple. The swashplate dynamics have been investigated experimentally, measuring the dynamic pressure which controls the pump displacement; a comparison with the numerical model results confirmed the high accuracy. An optimization process has been conducted on the valve plate geometry to control fluid-born noise by flow ripple reduction. The NLPQL algorithm is used since it is suitable for this study. The objective function to minimize is the well-known function, the Non-Uniformity Grade, a parameter directly correlated with flow ripple. A prototype of the best design has been realized and tested, confirming a reduction in the pressure ripple. An endurance test was also conducted. As predicted from the numerical model, a significant reduction of cavitation erosion was observed.

Analysis on the Side Leakage Amount of the Friction between Piston and Cylinder Block in Axial Piston Pump

2014 ◽  
Vol 635-637 ◽  
pp. 341-345 ◽  
Author(s):  
Wei Wang
Keyword(s):  
Flow Rate ◽  
Piston Pump ◽  
Cylinder Block ◽  
Correction Coefficient ◽  
Leakage Flow ◽  
Fluid Viscosity ◽  
Axial Piston Pump ◽  
Viscosity Change ◽  
Leakage Flow Rate ◽  
Axial Piston

The spherical distribution pairs of the plunger and the cylinder friction, has an important influence on the performance of spherical port plate axial piston pump. Based on the analysis of fluid viscosity change with pressure and temperature, considering friction differential pressure flow and shear flow, establishes the mathematics model of the friction pair of leakage. The simulation analysis using MATLAB software, the leakage flow rate is not proportional to pressure, but with the increase of pressure leakage flow was increased, and with the increase of pressure viscosity coefficient and temperature coefficient of viscosity, the leakage flow rate correction coefficient increases obviously, so in the choice of the hydraulic oil cylinder hole, should choose a relatively moving average leakage rate had no effect the piston ring slot.

Theoretical and Simulation Investigations on Flow Ripple Reduction of Axial Piston Pumps Using Nonuniform Distribution of Pistons

2020 ◽  
Vol 143 (4) ◽  
Author(s):  
Fei Lyu ◽  
Shaogan Ye ◽  
Junhui Zhang ◽  
Bing Xu ◽  
Weidi Huang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Optimization Design ◽  
Nonuniform Distribution ◽  
Piston Pump ◽  
Axial Piston Pump ◽  
Flow Ripple ◽  
Distribution Rule ◽  
Dynamic Simulation Model ◽  
Ripple Reduction ◽  
Axial Piston

Abstract The output flow ripple of the axial piston pump is one of the excitation sources for the hydraulic system vibration. The amplitudes of its specific harmonics must be reduced to avoid the resonance with the hydraulic pipeline. In this paper, a method on the nonuniform distribution of the pistons is put forward to adjust the flow ripple. The deflection angles of the pistons are used to describe the distribution rule. The distribution rule is imported to the Fourier expansion of the flow rate of each single-piston chamber, and then every single flow rate is superposed to obtain the Fourier coefficient of total flow rate that becomes the function of deflection angles. After this, objective optimization design is carried out to reduce the amplitudes of specific harmonics. Finally, the dynamic simulation model of the nonuniformly distributed axial piston pump is established to verify the effects of objective optimization. The results show that the amplitude of the ninth harmonic of the flow ripple can be reduced by about 40%, and the reductions are about 99% for the 18th and 27th harmonic.

scholarly journals Tribological Properties of Cylinder Block/Valve Plate Interface of Axial Piston Pump on the Tribometer

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Jiahai Huang ◽  
Zhenhua Dou ◽  
Zhenglei Wang ◽  
Long Quan ◽  
Linkai Niu
Keyword(s):  
Heat Treatment ◽  
Contact Pressure ◽  
Tribological Properties ◽  
Optimization Design ◽  
Valve Plate ◽  
Piston Pump ◽  
Cylinder Block ◽  
Axial Piston Pump ◽  
Plate Interface ◽  
Axial Piston

AbstractThe tribological properties of cylinder block/valve plate is an important consideration in the design of axial piston pump. The effect of materials and heat treatment on friction and wear properties has been studied in depth. Engineering experiences show that the speed and load also affect the tribological properties, but these have not been systematically analyzed. The purpose of this paper is to evaluate the tribological properties of the commonly used materials (CuPb15Sn5 and 38CrMoAl/42CrMo) for cylinder block/valve plate with different heat treatment and contact pressure at different speed. During the test, tribometer is used to simulate the contact pattern between the valve plate/cylinder block in axial piston pump, the friction coefficient, wear rate and surface topography are analyzed to evaluate the tribological properties of different types of friction samples at different speed. Results indicate that: (1) contact surface of the samples at 1800 r/min is more prone to adhesive wear than those at 500 r/min; (2) in the terms of wear resistance, quench-tempered and nitrided 38CrMoAl (38CrMoAl QTN for short) is better than quench-tempered and nitrided 42CrMo, although they are all commonly used materials in the axial piston pump; (3) 2.5 MPa is the critical contact pressure of the interface between valve plate made of 38CrMoAl QTN and cylinder block made of CuPb15Sn5 on the tribometer, which implies the pressure bearing area at the bottom of the cylinder block should be carefully designed; (4) the valve plate/cylinder block made of 38CrMoAl QTN/CuPb15Sn5 exhibits good tribological properties in a real axial piston pump. This research is useful for the failure analysis and structural optimization design of the valve plates/cylinder block.

Sign in / Sign up

Export Citation Format

Share Document