Performance of Abutment with Geocell Reinforced Cement Soil Backfill

2013 ◽  
Vol 353-356 ◽  
pp. 860-865
Author(s):  
Wen Ming Song ◽  
Yi Min Wang ◽  
Ye Kai Chen
Keyword(s):  
Shear Strength ◽  
Field Testing ◽  
Longitudinal Direction ◽  
Remarkable Effect ◽  
Direct Shear Tests ◽  
Strength Tests ◽  
Reinforced Cement ◽  
Strength And Deformation ◽  
Loading Tests ◽  
Cement Soil

Unconfined compressive strength tests of soil with different cement dosage of stabilization have been conducted to determine the optimum cement stabilizing dosage. And, the shear strength and deformation of the geocell reinforced cement soil have been investigated through a serial of direct shear tests and plate-loading tests. The results show that there is a significant improvement on shear strength and modulus of the soil by reinforcement. Moreover, FEM has been used to simulate and analyze the performance of abutment with geocell reinforced cement soil backfill. And the comparison of the computing results to field testing results has been carried out. The research results indicate that: the abutment with wedge-shape geocell reinforced cement soil backfill has remarkable effect on decreasing the differential settlement on bridge-embankment transition section. The gradient of settlement along the longitudinal direction of bridge-embankment gets much more smooth-going and less.

scholarly journals Strength Tests and Numerical Simulations of Loess Modified by Desulfurization Ash and Fly Ash

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 512
Author(s):  
Zhi Cheng ◽  
Xinrong Cheng ◽  
Yuchao Xie ◽  
Zhe Ma ◽  
Yuhao Liu
Keyword(s):  
Shear Strength ◽  
Fly Ash ◽  
Power Plants ◽  
Utilization Rate ◽  
Direct Shear ◽  
Test Results ◽  
Mass Ratio ◽  
Direct Shear Tests ◽  
Strength Tests ◽  
Actual Test

Desulfurization ash and fly ash are solid wastes discharged from boilers of power plants. Their utilization rate is low, especially desulfurization ash, most of which is stored. In order to realize their resource utilization, they are used to modify loess in this paper. Nine group compaction tests and 32 group direct shear tests are done in order to explore the influence law of desulfurization ash and fly ash on the strength of the loess. Meanwhile, FLAC3D software is used to numerically simulate the direct shear test, and the simulation results and the test results are compared and analyzed. The results show that, with the increase of desulfurization ash’s amount, the shear strength of the modified loess increases first and then decreases. The loess modified by the fly ash has the same law with that of the desulfurization ash. The best mass ratio of modified loess is 80:20. When the mass ratio is 80:20, the shear strength of loess modified by the desulfurization ash is 12.74% higher than that of the pure loess on average and the shear strength of loess modified by fly ash is 3.59% higher than that of the pure loess on average. The effect of the desulfurization ash on modifying the loess is better than that of the fly ash. When the mass ratio is 80:20, the shear strength of loess modified by the desulfurization ash is 9.15% higher than that of the fly ash on average. Comparing the results of the simulation calculation with the actual test results, the increase rate of the shear stress of the FLAC3D simulation is larger than that of the actual test, and the simulated shear strength is about 8.21% higher than the test shear strength.

Fibre reinforced polymer strengthening of the Sainte-Émélie-de-l'Énergie bridge: design, instrumentation, and field testing

2000 ◽  
Vol 27 (5) ◽  
pp. 916-927 ◽  
Author(s):  
P Labossière ◽  
K W Neale ◽  
P Rochette ◽  
M Demers ◽  
P Lamothe ◽  
...  
Keyword(s):  
Shear Strength ◽  
Composite Materials ◽  
Bending Strength ◽  
Field Testing ◽  
Longitudinal Direction ◽  
Concrete Bridges ◽  
Repair Work ◽  
Reinforcement Scheme ◽  
Reinforced Composite ◽  
Current Loading

An experimental research project was undertaken to evaluate the need to strengthen existing reinforced concrete bridges belonging to the Ministère des Transports du Québec. A typical bridge consisting of a single-span bridge with T-shaped sections was identified. Evaluation of the bridge showed that an increase in bending strength and shear strength would be necessary to satisfy current loading conditions and code requirements. The increase in bending strength was obtained by bonding carbon-reinforced composite materials to the underface of the beams, with fibres in the longitudinal direction. External U-shaped stirrups made of glass-reinforced composite materials were installed on the outside faces of the beams in order to increase their shear strength. This paper presents a selection of experimental results initially obtained on T-section beams, scaled 1:3 with respect to the bridge under consideration. The actual reinforcement scheme selected for the bridge is then presented, accompanied by comments on the construction process. Conventional instrumentation and fibre optic sensors were incorporated to the repair work in order to evaluate the behaviour of the bridge, before and after strengthening. Initial results of this ongoing evaluation are presented here.Key words: bridge strengthening, FRP, composite materials, instrumentation, field testing.

Study on the Relationship between Soil-Cement Parameters and Unconfined Compressive Strength

2011 ◽  
Vol 255-260 ◽  
pp. 4012-4016
Author(s):  
Jun Qing Ma ◽  
You Xi Wang
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Shear Strength ◽  
Unconfined Compressive Strength ◽  
Deformation Modulus ◽  
Soil Cement ◽  
Strength And Deformation ◽  
Cement Soil ◽  
Relationship Of ◽  
The Relationship

This paper studies relationship between soil-cement parameters and unconfined compressive strength. The research in tensile strength and deformation modulus of soil-cement is an important basis for soil-cement failure mechanism and intensity theory. They also impact cracks, deformation and durability of cement-soil structure. Shear strength and deformation of soil-cement is important to the destruction analysis and finite element calculations. Therefore it needs to study on tensile strength, shear strength and deformation modulus of soil-cement. Based on previous experiments, the relationship of tensile strength, shear strength, deformation modulus and unconfined compressive strength of soil-cement are quantitatively studied.

scholarly journals Study of Anisotropy Characteristics of Bogor Volcanic Soil

UKaRsT ◽  
2021 ◽  
Vol 5 (1) ◽  
pp. 95
Author(s):  
Yusi Sulastri ◽  
Paulus Pramono Rahardjo
Keyword(s):  
Shear Strength ◽  
Field Testing ◽  
Deposition Process ◽  
Soil Parameters ◽  
Compression Index ◽  
Volcanic Soil ◽  
Horizontal Shear ◽  
Coefficient Of Consolidation ◽  
General Anisotropy ◽  
Strength Tests

Anisotropy in soil results from the deposition process which describes the characteristics of the soil grains or is caused by stress or from the consequences of stresses caused during deposition and subsequent erosion. All soils behave in general anisotropy and some exhibit undrained shear strength. This study conducted 2 tests, namely the first field testing with original soil samples in the form of CPTu and dilatometer. The CPTu test's objective is to determine the vertical soil parameters, while the dilatometer is to determine the horizontal soil parameters. This study indicates that the indication of anisotropy in all shear strength tests is evident in the results of the CPTu test and the Dilatometer test. TX - UU and consolidation show that the horizontal shear strength (Suh) is greater than the vertical slope shear strength (Suv). In this case, the ratio obtained for shear strength is Suh = 1.3 Suv. And from the results of the consolidation test in the laboratory, it was found that the horizontal compression index parameter  (Cc horizontal) was greater than the vertical (Cc vertical) and the horizontal coefficient of consolidation (Ch) is greater than the vertical coefficient of consolidation (Cv).

Influence of Density on the Hydraulic and Mechanical Properties of Sands

2014 ◽  
Vol 580-583 ◽  
pp. 659-664
Author(s):  
Osvaldo de Freitas Neto ◽  
Olavo Francisco dos Santos Jr. ◽  
Ricardo Nascimento Flores Severo
Keyword(s):  
Shear Strength ◽  
Hydraulic Conductivity ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Coarse Fraction ◽  
Direct Shear ◽  
Direct Shear Tests ◽  
Strength Tests ◽  
Constant Head ◽  
Direct Shear Testing

This article aims at assessing the influence of relative density on the hydraulic conductivity and shear strength of two sands, denominated S01 and S02, derived from different regions and formation processes. S01 is wind-blown and S2 alluvial. The results of characterization and hydraulic conductivity in constant head tests were presented for both samples. The results of direct shear tests with sand S01 prepared with 5 different void ratios were also presented, for a vertical stress of 100kPa. The S02 sample was prepared with 4 different void ratios and these underwent direct shear testing with vertical stresses of 25kPa and 150kPa. This sample was prepared with the maximum and minimum void ratio and submitted to strength tests at CD triaxial compression with confining stresses of 50kPa, 100kPa and 200kPa. Results showed that even with different grain sizes, and under different density conditions, there were no significant variations in the permeability of the materials. With respect to shear strength, sand S01 obtained higher angle of friction values than sand S02, even though the latter had a higher percent coarse fraction. Sand S02 was relatively similar in terms of friction angle values obtained in direct shear and triaxial compression strength tests.

Shear strength and deformation modeling of conventionally reinforced short coupling beams

2021 ◽  
Vol 239 ◽  
pp. 112282
Author(s):  
Ke-Jing Zhou ◽  
Wei-Jian Yi ◽  
Hui Chen ◽  
Yun Zhou ◽  
Wang-Xi Zhang
Keyword(s):  
Shear Strength ◽  
Coupling Beams ◽  
Strength And Deformation

scholarly journals Mechanical Properties and Micro Mechanism of Nano-Clay-Modified Soil Cement Reinforced by Recycled Sand

2021 ◽  
Vol 13 (14) ◽  
pp. 7758
Author(s):  
Biao Qian ◽  
Wenjie Yu ◽  
Beifeng Lv ◽  
Haibo Kang ◽  
Longxin Shu ◽  
...  
Keyword(s):  
Shear Strength ◽  
Void Ratio ◽  
Soil Mass ◽  
Direct Shear ◽  
Test Results ◽  
The Sustainable Development ◽  
Direct Shear Tests ◽  
Soil Cement ◽  
Nano Clay ◽  
New Material

To observe the effect of recycled sand and nano-clay on the improvement of the early strength of soil-cement (7d), 0%, 10%, 15% and 20% recycled sand were added. While maintaining a fixed moisture content of 30%, the ratios of each material are specified in terms of soil mass percentage. The shear strength of CSR (recycled sand blended soil-cement) was investigated by direct shear test and four groups of specimens (CSR-1, CSR-2, CSR-3 and CSR-4) were obtained. In addition, 8% nano-clay was added to four CSR groups to obtain the four groups of CSRN-1, CSRN-2, CSRN-3 and CSRN-4 (soil-cement mixed with recycled sand and nano-clay), which were also subjected to direct shear tests. A detailed analysis of the modification mechanism of soil-cement by recycled sand and nano-clay was carried out in combination with scanning electron microscopy (SEM) and IPP (ImagePro-Plus) software. The test results showed that: (1) CSR-3 has the highest shear strength due to the “concrete-like” effect of the incorporation of recycled sand. With the addition of 8% nano-clay, the overall shear strength of the cement was improved, with CSRN-2 having the best shear strength, thanks to the filling effect of the nano-clay and its high volcanic ash content. (2) When recycled sand and nano-clay were added to soil-cement, the improvement in shear strength was manifested in a more reasonable macroscopic internal structure distribution of soil-cement. (3) SEM test results showed that the shear strength was negatively correlated with the void ratio of its microstructure. The smaller the void ratio, the greater the shear strength. This shows that the use of reclaimed sand can improve the sustainable development of the environment, and at the same time, the new material of nano-clay has potential application value.

scholarly journals Evaluation of Undrained Shear Strength of Miocene Clay from the Weight Sounding Test (WST)

2017 ◽  
Vol 62 (2) ◽  
pp. 367-384
Author(s):  
Sebastian Olesiak
Keyword(s):  
Shear Strength ◽  
Field Testing ◽  
Field Investigation ◽  
Undrained Shear Strength ◽  
Cohesive Soils ◽  
Strength Parameters ◽  
Additional Measurement ◽  
Carpathian Foredeep ◽  
Innovative Solution ◽  
Undrained Shear

Abstract Soil strength parameters needed for the calculation of bearing capacity and stability are increasingly determined from field testing. This paper presents a method to determine the undrained shear strength cuWST of the soil, based on the Weight Sounding Test (WST). The innovative solution which allows for a significant reduction of equipment needed for geotechnical field investigation is presented. The proposed method is based on an additional measurement of the torque during testing. It then becomes possible to estimate the undrained shear strength, cuWST of the soil, using the correlation given in this paper. The research results presented in this paper were carried out on selected cohesive soils, Miocene clays from the Carpathian Foredeep.

Sign in / Sign up

Export Citation Format

Share Document