scholarly journals Study of Anisotropy Characteristics of Bogor Volcanic Soil

UKaRsT ◽  
2021 ◽  
Vol 5 (1) ◽  
pp. 95
Author(s):  
Yusi Sulastri ◽  
Paulus Pramono Rahardjo
Keyword(s):  
Shear Strength ◽  
Field Testing ◽  
Deposition Process ◽  
Soil Parameters ◽  
Compression Index ◽  
Volcanic Soil ◽  
Horizontal Shear ◽  
Coefficient Of Consolidation ◽  
General Anisotropy ◽  
Strength Tests

Anisotropy in soil results from the deposition process which describes the characteristics of the soil grains or is caused by stress or from the consequences of stresses caused during deposition and subsequent erosion. All soils behave in general anisotropy and some exhibit undrained shear strength. This study conducted 2 tests, namely the first field testing with original soil samples in the form of CPTu and dilatometer. The CPTu test's objective is to determine the vertical soil parameters, while the dilatometer is to determine the horizontal soil parameters. This study indicates that the indication of anisotropy in all shear strength tests is evident in the results of the CPTu test and the Dilatometer test. TX - UU and consolidation show that the horizontal shear strength (Suh) is greater than the vertical slope shear strength (Suv). In this case, the ratio obtained for shear strength is Suh = 1.3 Suv. And from the results of the consolidation test in the laboratory, it was found that the horizontal compression index parameter  (Cc horizontal) was greater than the vertical (Cc vertical) and the horizontal coefficient of consolidation (Ch) is greater than the vertical coefficient of consolidation (Cv).

Performance of Abutment with Geocell Reinforced Cement Soil Backfill

2013 ◽  
Vol 353-356 ◽  
pp. 860-865
Author(s):  
Wen Ming Song ◽  
Yi Min Wang ◽  
Ye Kai Chen
Keyword(s):  
Shear Strength ◽  
Field Testing ◽  
Longitudinal Direction ◽  
Remarkable Effect ◽  
Direct Shear Tests ◽  
Strength Tests ◽  
Reinforced Cement ◽  
Strength And Deformation ◽  
Loading Tests ◽  
Cement Soil

Unconfined compressive strength tests of soil with different cement dosage of stabilization have been conducted to determine the optimum cement stabilizing dosage. And, the shear strength and deformation of the geocell reinforced cement soil have been investigated through a serial of direct shear tests and plate-loading tests. The results show that there is a significant improvement on shear strength and modulus of the soil by reinforcement. Moreover, FEM has been used to simulate and analyze the performance of abutment with geocell reinforced cement soil backfill. And the comparison of the computing results to field testing results has been carried out. The research results indicate that: the abutment with wedge-shape geocell reinforced cement soil backfill has remarkable effect on decreasing the differential settlement on bridge-embankment transition section. The gradient of settlement along the longitudinal direction of bridge-embankment gets much more smooth-going and less.

Physical properties of dewatered wastewater sludge for landfilling

1996 ◽  
Vol 34 (3-4) ◽  
pp. 533-540 ◽  
Author(s):  
A. Koenig ◽  
J. N. Kay ◽  
I. M. Wan
Keyword(s):  
Shear Strength ◽  
Hong Kong ◽  
Municipal Wastewater ◽  
Compressibility Factor ◽  
Wastewater Sludge ◽  
Municipal Wastewater Treatment ◽  
Intrinsic Resistance ◽  
Coefficient Of Consolidation ◽  
Minimum Requirement ◽  
Geotechnical Stability

In the context of landfilling dewatered wastewater sludge in Hong Kong, with landfills up to 140 m high, one of the most significant properties of sludge is its physical nature with regard to moisture characteristics and associated geotechnical stability. Commonly, lower limits are set on total solids content, but no geotechnical stability criteria are applied with the exception of Germany where a minimum requirement for vane shear strength is set at 25 kN/m2. The purpose of this study was to determine and evaluate dewatered wastewater sludge from three Hong Kong municipal wastewater treatment plants with regard to the following physical and geotechnical properties: (i) vane shear strength; (ii) consolidation characteristics such as compression index, compressibility factor, coefficient of consolidation and compressibility coefficient; and (iii) hydraulic characteristics such as permeability and intrinsic resistance. Although dewatered sludge exhibits quite different characteristics as compared to soils, predictive logarithmic relationships may be established between various properties which are consistent with the critical state model for soils, conventional filtration and consolidation theory. Such representation provides a valuable basis for understanding the sludge characteristics and behaviour to landfill design.

Finite Element Modeling of a Mechanically Stabilized Earth Trial Wall

2021 ◽  
pp. 036119812110164
Author(s):  
Andrew Lees ◽  
Michael Dobie
Keyword(s):  
Finite Element ◽  
Shear Strength ◽  
Retaining Wall ◽  
Back Analysis ◽  
Soil Parameters ◽  
Failure Behavior ◽  
Valuable Insight ◽  
Deformation And Failure ◽  
First Case ◽  
Soil Shear Strength

Polymer geogrid reinforced soil retaining walls have become commonplace, with routine design generally carried out by limiting equilibrium methods. Finite element analysis (FEA) is becoming more widely used to assess the likely deformation behavior of these structures, although in many cases such analyses over-predict deformation compared with monitored structures. Back-analysis of unit tests and instrumented walls improves the techniques and models used in FEA to represent the soil fill, reinforcement and composite behavior caused by the stabilization effect of the geogrid apertures on the soil particles. This composite behavior is most representatively modeled as enhanced soil shear strength. The back-analysis of two test cases provides valuable insight into the benefits of this approach. In the first case, a unit cell was set up such that one side could yield thereby reaching the active earth pressure state. Using FEA a test without geogrid was modeled to help establish appropriate soil parameters. These parameters were then used to back-analyze a test with geogrid present. Simply using the tensile properties of the geogrid over-predicted the yield pressure but using an enhanced soil shear strength gave a satisfactory comparison with the measured result. In the second case a trial retaining wall was back-analyzed to investigate both deformation and failure, the failure induced by cutting the geogrid after construction using heated wires. The closest fit to the actual deformation and failure behavior was provided by using enhanced fill shear strength.

scholarly journals Improved strength properties of LVL glued using PVAc adhesives with physical treatment-based Rubberwood (Hevea brasiliensis)

2020 ◽  
Vol 5 (1) ◽  
pp. 711-725
Author(s):  
Sutrisno ◽  
Eka Mulya Alamsyah ◽  
Ginanjar Gumilar ◽  
Takashi Tanaka ◽  
Masaaki Yamada
Keyword(s):  
Shear Strength ◽  
Hevea Brasiliensis ◽  
Formaldehyde Emission ◽  
Strength Properties ◽  
Modulus Of Rupture ◽  
Horizontal Shear ◽  
Physical Treatment ◽  
Cold Pressing ◽  
Laminated Veneer Lumber ◽  
Pressing Time

AbstractThe properties of the laminated veneer lumber (LVL) composed of the boiled veneer of Rubberwood (Hevea brasiliensis) using polyvinyl acetate (PVAc) adhesives in various cold-pressing time and various conditioned time with loaded and unloaded were studied. Five-ply LVL was produced by boiling veneer at 100°C for 90 min as pretreatment and cold-pressing time at 12 kgf cm−2 for 1.5, 6, 18, and 24 h then conditioned at 20°C and 65% relative humidity (RH) with loaded (12 kgf cm−2) and unloaded for 7 days as physical treatment. Especially for the delamination test, the specimens were immersed at 70 ± 3°C for 2 h and dried in the oven at 60 ± 3°C for 24 h; then, the specimens were solidified at room temperature (20°C and 65% RH) with loaded (12 kgf cm−2) and unloaded for 7, 10, 12, and 14 days. To determine the performance of LVL, the density, moisture content (MC), delamination, modulus of elasticity (MOE), modulus of rupture (MOR), horizontal shear strength, and formaldehyde emission tests were conducted according to the Japanese Agricultural Standard (JAS 2008) for structural LVL. The MOE and MOR values were significantly influenced by the physical treatment, however, neither to horizontal shear strength nor to formaldehyde emission. The best performance of LVL has resulted from unloaded LVL with cold-pressed time for 18 h; the MOE and MOR values were 9,345.05 ± 141.61 N mm−2 and 80.67 ± 1.77 N mm−2, respectively. The best value of the horizontal shear strength was obtained from the LVL with 18 h cold-pressing time and conditioned with loaded (13.10 ± 1.47 N mm−2) and unloaded (12.23 ± 1.36 N mm−2). The percentage of delamination values decreased with an increase in the cold-pressing time and conditioning time. The lowest value of delamination (19.06%) was obtained from the LVL with 24 h cold-pressing time and conditioned with loaded for 14 days. Except the delamination test, all other properties fulfilled the JAS.

scholarly journals Evaluation of Undrained Shear Strength of Miocene Clay from the Weight Sounding Test (WST)

2017 ◽  
Vol 62 (2) ◽  
pp. 367-384
Author(s):  
Sebastian Olesiak
Keyword(s):  
Shear Strength ◽  
Field Testing ◽  
Field Investigation ◽  
Undrained Shear Strength ◽  
Cohesive Soils ◽  
Strength Parameters ◽  
Additional Measurement ◽  
Carpathian Foredeep ◽  
Innovative Solution ◽  
Undrained Shear

Abstract Soil strength parameters needed for the calculation of bearing capacity and stability are increasingly determined from field testing. This paper presents a method to determine the undrained shear strength cuWST of the soil, based on the Weight Sounding Test (WST). The innovative solution which allows for a significant reduction of equipment needed for geotechnical field investigation is presented. The proposed method is based on an additional measurement of the torque during testing. It then becomes possible to estimate the undrained shear strength, cuWST of the soil, using the correlation given in this paper. The research results presented in this paper were carried out on selected cohesive soils, Miocene clays from the Carpathian Foredeep.

Deformability and consolidation characteristics of soft Bangkok clay using screw plate tests

1990 ◽  
Vol 27 (5) ◽  
pp. 531-545 ◽  
Author(s):  
D. T. Bergado ◽  
K. C. Chong ◽  
P. A. M. Daria ◽  
M. C. Alfaro
Keyword(s):  
Graphical Method ◽  
Soft Clay ◽  
Stress Path ◽  
Soil Parameters ◽  
Test Results ◽  
Coefficient Of Consolidation ◽  
Plate Test ◽  
Settlement Time ◽  
Oedometer Tests ◽  
Test Embankment

This study centred on the performance of the screw plate test (SPLT) to determine the deformability and consolidation characteristics of soft Bangkok clay. For comparison, a series of stress-path-controlled triaxial consolidation tests (tri) were carried out on good quality samples of Bangkok clay taken from the same testing sites and imposed with the same loading conditions as the screw plate tests. Undrained and drained moduli and coefficients of consolidation were obtained from the stress-path-controlled triaxial consolidation tests and were compared with the corresponding values of the screw plate test. In addition, the ultimate bearing capacity was derived from the pressure–deformation relationships of the screw plate test results. A graphical method was used to compute the coefficient of consolidation from the screw plate tests and from stress-path-controlled triaxial consolidation test results. The compressibility data were also obtained from conventional oedometer tests (oed). Both cv (SPLT)/cv (tri) and cv (SPLT)/cv(oed) ratios compared favorably with the cv (field)/cv (laboratory) ratio obtained from past investigations. The data from pressure–settlement–time relationships of the screw plate tests were used to successfully predict values that compared favorably with the measured values at each stress level. The pressure–deformation–time relationship from stress-path-controlled triaxial consolidation tests were also evaluated, and they indicated behaviour similar to that of the screw plate test results. Soil parameters obtained from screw plate tests were subsequently used to predict the settlement of two test embankments, giving fairly close agreement with the observed values. Key words: soft clay, settlement, deformation, consolidation, screw plate test, triaxial test, embankment, prediction, stress path.

scholarly journals Experimental and Numerical Investigation on the Stability of Loess Embankment Treated by Chemical Solution under Freezing-Thawing Conditions

2021 ◽  
Author(s):  
Hua Liu ◽  
Zelin Niu ◽  
Yuanhong Dong ◽  
Naifei Liu ◽  
Shuocheng Zhang
Keyword(s):  
Shear Strength ◽  
Safety Factor ◽  
Limit Equilibrium ◽  
Solution Concentration ◽  
Chemical Solution ◽  
Compression Index ◽  
Limit Equilibrium Methods ◽  
Novel Method ◽  
The Stability ◽  
Embankment Stability

Abstract In order to study the influence of chemical solution on the stability of loess embankment in seasonally frozen regions, the compression index, shear strength index and embankment safety factor of compacted loess fillings that were treated by different concentrations of chemical solution were analyzed through laboratory test and slope stability analysis program. The experimental results showed that the collapsible coefficients of remolded loess treated by different chemical solution will all increase which comparing the distilled water, and then will change again after freezing-thawing cycles (FTCs). The compression index of undisturbed loess will show regularity with the increase of chemical solution concentration. The shear strength of remolded loess also changed under the chemical solution and FTCs. Besides, simulation of the strength parameters by limit equilibrium methods showed that the safety factor of loess embankment with treatment of solution was significantly higher than that of untreated one, and the FTC would cause a further deterioration. The embankment stability improved after treated by chemical solution without considering seepage of rainwater. These results would provide a novel method to the problem of embankment stability related to environmental condition changes.

scholarly journals An Experimental Study on a Composite Bonding Structure for Steel Bridge Deck Pavements

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Xiaoguang Zheng ◽  
Qi Ren ◽  
Huan Xiong ◽  
Xiaoming Song
Keyword(s):  
Tensile Strength ◽  
Shear Strength ◽  
Epoxy Resin ◽  
Bonding Strength ◽  
Bridge Deck ◽  
Steel Bridge ◽  
Shear Tests ◽  
Bonding Structure ◽  
Asphalt Overlay ◽  
Strength Tests

As one of the major contributors to the early failures of steel bridge deck pavements, the bonding between steel and asphalt overlay has long been a troublesome issue. In this paper, a novel composite bonding structure was introduced consisting of epoxy resin micaceous iron oxide (EMIO) primer, solvent-free epoxy resin waterproof layer, and ethylene-vinyl acetate (EVA) hot melt pellets. A series of strength tests were performed to study its mechanical properties, including pull-off strength tests, dumbbell tensile tests, lap shear tests, direct tension tests, and 45°-inclined shear tests. The results suggested that the bonding structure exhibited fair bonding strength, tensile strength, and shear strength. Anisotropic behaviour was also observed at high temperatures. For epoxy resin waterproof layer, the loss of bonding strength, tensile strength, and shear strength at 60°C was 70%, 35%, and 39%, respectively. Subsequent pavement performance-oriented tests included five-point bending tests and accelerated wheel tracking tests. The impacts of bonding on fatigue resistance and rutting propagation were studied. It was found that the proposed bonding structure could provide a durable and well-bonded interface and was thus beneficial to prolong the fatigue lives of asphalt overlay. The choice of bonding materials was found irrelevant to the ultimate rutting depth of pavements. But the bonding combination of epoxy resin waterproof and EVA pellets could delay the early-stage rutting propagation.

scholarly journals Strength Tests and Numerical Simulations of Loess Modified by Desulfurization Ash and Fly Ash

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 512
Author(s):  
Zhi Cheng ◽  
Xinrong Cheng ◽  
Yuchao Xie ◽  
Zhe Ma ◽  
Yuhao Liu
Keyword(s):  
Shear Strength ◽  
Fly Ash ◽  
Power Plants ◽  
Utilization Rate ◽  
Direct Shear ◽  
Test Results ◽  
Mass Ratio ◽  
Direct Shear Tests ◽  
Strength Tests ◽  
Actual Test

Desulfurization ash and fly ash are solid wastes discharged from boilers of power plants. Their utilization rate is low, especially desulfurization ash, most of which is stored. In order to realize their resource utilization, they are used to modify loess in this paper. Nine group compaction tests and 32 group direct shear tests are done in order to explore the influence law of desulfurization ash and fly ash on the strength of the loess. Meanwhile, FLAC3D software is used to numerically simulate the direct shear test, and the simulation results and the test results are compared and analyzed. The results show that, with the increase of desulfurization ash’s amount, the shear strength of the modified loess increases first and then decreases. The loess modified by the fly ash has the same law with that of the desulfurization ash. The best mass ratio of modified loess is 80:20. When the mass ratio is 80:20, the shear strength of loess modified by the desulfurization ash is 12.74% higher than that of the pure loess on average and the shear strength of loess modified by fly ash is 3.59% higher than that of the pure loess on average. The effect of the desulfurization ash on modifying the loess is better than that of the fly ash. When the mass ratio is 80:20, the shear strength of loess modified by the desulfurization ash is 9.15% higher than that of the fly ash on average. Comparing the results of the simulation calculation with the actual test results, the increase rate of the shear stress of the FLAC3D simulation is larger than that of the actual test, and the simulated shear strength is about 8.21% higher than the test shear strength.

Sign in / Sign up

Export Citation Format

Share Document