Study on Optimum Meshing Efficiency for Spiral Bevel Gears in Mixed Elasto-Hydrodynamic Lubrication

2010 ◽  
Vol 37-38 ◽  
pp. 1321-1326
Author(s):  
Jian Gong Gu ◽  
Zong De Fang ◽  
Shan Shan Shen
Keyword(s):  
Friction Factor ◽  
Boundary Lubrication ◽  
Power Loss ◽  
Sliding Friction ◽  
Hydrodynamic Lubrication ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
The Mean ◽  
Spiral Bevel ◽  
Contact Parameters

The mean sliding friction factor was derived in the mixed elasto-hydrodynamic lubrication state, which contains the complete elasto-hydrodynamic and boundary lubrication synchronously. Based on the geometry and load contact characteristics of spiral bevel gears, the power loss from sliding friction of each point on the long axis of the instantaneous contact ellipse was calculated. Meanwhile, the function of sliding friction power loss in a mesh cycle was established. The meshing efficiency was obtained by integrating the above function. In addition, the meshing efficiency was increased through optimizing the contact parameters. The validity and superiority of the algorithm was demonstrated with analyzing an example.

Influence of Position Errors on EHD Lubrication in Spiral Bevel Gears

2010 ◽  
Author(s):  
Vilmos Simon
Keyword(s):  
Friction Factor ◽  
Carrying Capacity ◽  
Load Carrying Capacity ◽  
Oil Viscosity ◽  
Spiral Bevel Gears ◽  
Oil Film ◽  
Bevel Gears ◽  
Ehd Lubrication ◽  
Load Carrying ◽  
Spiral Bevel

The thermal elastohydrodynamic analysis of lubrication is applied to investigate the influence of misalignments of the meshing members on lubrication in spiral bevel gears. The calculation is based on the simultaneous solution of the Reynolds, elasticity, energy, and Laplace’s equations. The full thermal EHD lubrication analysis is applied, therefore, the oil viscosity variation with respect to pressure and temperature and the density variation with respect to pressure are included. By using the corresponding computer program, the influence of pinion’s running offset and axial adjustment errors, and angular position error of pinion axis on maximum oil film pressure and temperature, EHD load carrying capacity, and on power losses in the oil film is investigated. On the basis of the obtained results it can be concluded that the EHD load carrying capacity and the friction factor are very sensitive to misalignments of the mating members in the spiral bevel gear pair, the friction factor is reduced by the increase of EHD load carrying capacity and vise versa, and the maximum inlet oil temperature is almost insensitive to the misalignments.

A New Computational Method of the Friction Power Loss of Spiral Bevel Gears of a Helicopter Reducer

ICTE 2015 ◽  
2015 ◽  
Author(s):  
Yuan Li ◽  
Jiehong Yuan ◽  
Lijun Song ◽  
Guiming Mei ◽  
Kunlun Zhang ◽  
...  
Keyword(s):  
Power Loss ◽  
Computational Method ◽  
Spiral Bevel Gears ◽  
Friction Power ◽  
Bevel Gears ◽  
Spiral Bevel

scholarly journals Contact stiffness and damping of spiral bevel gears under transient mixed lubrication conditions

Friction ◽  
2021 ◽  
Author(s):  
Zongzheng Wang ◽  
Wei Pu ◽  
Xin Pei ◽  
Wei Cao
Keyword(s):  
Contact Stiffness ◽  
Mixed Lubrication ◽  
Asperity Contact ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Dry Contact ◽  
Spiral Bevel ◽  
Stiffness And Damping ◽  
Lubrication Conditions ◽  
Film Lubrication

AbstractExisting studies primarily focus on stiffness and damping under full-film lubrication or dry contact conditions. However, most lubricated transmission components operate in the mixed lubrication region, indicating that both the asperity contact and film lubrication exist on the rubbing surfaces. Herein, a novel method is proposed to evaluate the time-varying contact stiffness and damping of spiral bevel gears under transient mixed lubrication conditions. This method is sufficiently robust for addressing any mixed lubrication state regardless of the severity of the asperity contact. Based on this method, the transient mixed contact stiffness and damping of spiral bevel gears are investigated systematically. The results show a significant difference between the transient mixed contact stiffness and damping and the results from Hertz (dry) contact. In addition, the roughness significantly changes the contact stiffness and damping, indicating the importance of film lubrication and asperity contact. The transient mixed contact stiffness and damping change significantly along the meshing path from an engaging-in to an engaging-out point, and both of them are affected by the applied torque and rotational speed. In addition, the middle contact path is recommended because of its comprehensive high stiffness and damping, which maintained the stability of spiral bevel gear transmission.

Deformations and Stresses in Face-Hobbed Spiral Bevel Gears

2011 ◽  
Author(s):  
Vilmos V. Simon
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Nodal Point ◽  
Design Parameters ◽  
Element Discretization ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Tooth Surfaces ◽  
Spiral Bevel ◽  
Element Method

In this study an attempt is made to predict displacements and stresses in face-hobbed spiral bevel gears by using the finite element method. A displacement type finite element method is applied with curved, 20-node isoparametric elements. A method is developed for the automatic finite element discretization of the pinion and the gear. The full theory of the generation of tooth surfaces of face-hobbed spiral bevel gears is applied to determine the nodal point coordinates on tooth surfaces. The boundary conditions for the pinion and the gear are set automatically as well. A computer program was developed to implement the formulation provided above. By using this program the influence of design parameters and load position on tooth deflections and fillet stresses is investigated. On the basis of the results, obtained by performing a big number of computer runs, by using regression analysis and interpolation functions, equations for the calculation of tooth deflections and fillet stresses are derived.

scholarly journals Lubrication characteristics of gear after shot peening base on 25-pellet model

2018 ◽  
Vol 10 (7) ◽  
pp. 168781401879065 ◽  
Author(s):  
Shuai Mo ◽  
Shengping Zhu ◽  
Guoguang Jin ◽  
Jiabei Gong ◽  
Zhanyong Feng ◽  
...  
Keyword(s):  
Shot Peening ◽  
High Speed ◽  
Target Material ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Spiral Bevel ◽  
Lubrication Characteristics

High-speed heavy-load spiral bevel gears put forward high requirement for flexural strength; shot peening is a technique that greatly improves the bending fatigue strength of gears. During shot peening, a large number of fine pellets bombard the surface of the metal target material at very high speeds and let the target material undergo plastic deformation, at the same time strengthening layer is produced. Spiral bevel gear as the object of being bombarded inevitably brought the tooth surface micro-morphology changes. In this article, we aim to reveal the effect of microtopography of tooth shot peening on gear lubrication in spiral bevel gear, try to establish a reasonable description of the microscopic morphology for tooth surface by shot peening, to reveal the lubrication characteristics of spiral bevel gears after shot peening treatment based on the lubrication theory, and do comparative research on the surface lubrication characteristics of a variety of microstructures.

Sign in / Sign up

Export Citation Format

Share Document