Study on the Basic Mechanical Properties of Recycled Concrete Hollow Block Masonry

2013 ◽  
Vol 438-439 ◽  
pp. 749-755 ◽  
Author(s):  
Tong Hao ◽  
Dong Li
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Shear Behavior ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Test Results ◽  
Aggregate Concrete ◽  
Mortar Strength ◽  
Hollow Block

By the experimental studying on the basic mechanical properties of recycled concrete hollow block masonry, the compressive and shear behavior of recycled aggregate concrete hollow block masonry under different mortar strength were analyzed. Research indicated that the compressive and shear behavior of recycled aggregate concrete hollow block masonry was similar to that of ordinary concrete hollow block masonry. The normal formula was recommended to calculate the compressive strength of the masonry. The shear strength of the masonry was affected by the mortar strength. The shear strength calculation formula of recycled concrete hollow block masonry was proposed according to the formula of masonry design code. The calculating results were in good agreement with the test results.

scholarly journals Mechanical Properties of a New Type Recycled Aggregate Concrete Interlocking Hollow Block Masonry

2021 ◽  
Vol 13 (2) ◽  
pp. 745
Author(s):  
Jie Li ◽  
Hao Zhou ◽  
Wenwen Chen ◽  
Zhongfan Chen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Shear Strength ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Test Results ◽  
Hollow Block ◽  
New Type ◽  
Building Engineering

Considering the advantages of energy conservation and reducing the construction skill requirement of the workers, a new type of interlocking hollow block using recycled aggregates concrete (IHB-RAC) with the compressive strength up to 10 Mpa was proposed, which could help improve more than 56% of the construction efficiency compared to commonly used concrete hollow blocks. In order to study the mechanical properties and promote the application of this new type block in building engineering, the masonries considering different strengths of mortar and the concrete used in the grouting holes were designed, and the corresponding compressive and shear strength, as well as the failure mode of the masonries were studied according to the test results. Then, experimental results were compared with the calculated values obtained from Chinese code GB50003-2011 to check the suitability of the standards. In order to make an accurate prediction of the compressive strength of the masonry, modifying coefficients were suggested considering the positive contributions of the connecting keys. In addition, according to the test results, an appropriate calculation method for accurately predicting the shear strength of the grouted IHB-RAC masonry was proposed by separately considering the effort of the mortar and the grouting hole concrete.

scholarly journals Experimental Study on the Mechanical Properties and Compression Size Effect of Recycled Aggregate Concrete

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2323
Author(s):  
Yubing Du ◽  
Zhiqing Zhao ◽  
Qiang Xiao ◽  
Feiting Shi ◽  
Jianming Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Size Effect ◽  
Compressive Stress ◽  
Failure Modes ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Aggregate Concrete ◽  
Substitution Ratio ◽  
The Impact

To explore the basic mechanical properties and size effects of recycled aggregate concrete (RAC) with different substitution ratios of coarse recycled concrete aggregates (CRCAs) to replace natural coarse aggregates (NCA), the failure modes and mechanical parameters of RAC under different loading conditions including compression, splitting tensile resistance and direct shear were compared and analyzed. The conclusions drawn are as follows: the failure mechanisms of concrete with different substitution ratios of CRCAs are similar; with the increase in substitution ratio, the peak compressive stress and peak tensile stress of RAC decrease gradually, the splitting limit displacement decreases, and the splitting tensile modulus slightly increases; with the increase in the concrete cube’s side length, the peak compressive stress of RAC declines gradually, but the integrity after compression is gradually improved; and the increase in the substitution ratio of the recycled aggregate reduces the impact of the size effect on the peak compressive stress of RAC. Furthermore, an influence equation of the coupling effect of the substitution ratio and size effect on the peak compressive stress of RAC was quantitatively established. The research results are of great significance for the engineering application of RAC and the strength selection of RAC structure design.

Shear strength of reinforced concrete beams with recycled aggregates

2019 ◽  
Vol 22 (8) ◽  
pp. 1938-1951 ◽  
Author(s):  
George Wardeh ◽  
Elhem Ghorbel
Keyword(s):  
Tensile Strength ◽  
Shear Strength ◽  
Strain Softening ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Opening Displacement ◽  
Aggregate Concrete ◽  
Natural Aggregate ◽  
Hinge Model

This article presents an experimental program on the shear behavior of beams without transversal reinforcement manufactured with natural aggregate concrete and 100% recycled aggregate concrete. The beams were tested under four-point bending for a shear span-to-depth ratio ( a/ d) equal to 1.5 and 3.0. The mechanical properties of two mixes were characterized in terms of compressive strength, splitting tensile strength, and elastic modulus. Three-point bending tests were performed on plain pre-notched samples in order to determine the fracture properties by an inverse analysis of experimental force–crack mouth opening displacement curves using the analytical nonlinear hinge model and a power law strain-softening relationship. The strain-softening law is described by two parameters being, respectively, the power n and the critical crack opening displacement wc. The experimental results show that, for the same class of compressive strength, tensile strength, fracture energy, and the shear strength of recycled aggregate concrete are lower than natural aggregate concrete. The decrease in the fracture energy and the shear strength is consistent with the decrease in the splitting tensile strength of the recycled aggregate concrete mixes compared to the natural aggregate concrete. Critical shear crack theory was adopted to model the shear behavior of beams tested with a/ d = 3.0. For an accurate evaluation of the deformation capacity of tested beams, the nonlinear hinge model for recycled concrete members was extended to recycled concrete sections. For deep beams ( a/ d = 1.5), the strut-and-tie model was used. Finally, comparisons of prediction models to a wide range of experimental data are presented.

Meso-Analysis of Dynamic Compressive Behavior of Recycled Aggregate Concrete Using BFEM

2019 ◽  
Vol 17 (06) ◽  
pp. 1950013 ◽  
Author(s):  
Liping Ying ◽  
Yijiang Peng ◽  
Hongming Yang
Keyword(s):  
Mechanical Properties ◽  
High Strain ◽  
Dynamic Mechanical Properties ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Aggregate Concrete ◽  
Dynamic Mechanical ◽  
Concrete Materials ◽  
Dynamic Damage

In this paper, the base force element method (BFEM) for dynamic damage problems is proposed. And the BFEM model was applied to investigate the dynamic mechanical behavior of recycled aggregate concrete (RAC). Any convex polygon recycled aggregate was simulated. A constitutive relationship of dynamic damage was given. The compression test under dynamic loadings on the recycled concrete specimen was simulated. The stress–strain softening curve, variation law of dynamic enhancement coefficient and the damage pattern were researched under different strain rates. The dynamic properties of recycled concrete materials at high strain rate are also studied. The effect of different aggregate distribution on the mechanical properties of concrete was studied. The results of dynamic calculation of recycled concrete materials by this method are compared with the experimental results. The numerical simulation results are in good agreement with the experimental results. The comparative analysis on the dynamic mechanical properties of RAC and natural aggregate concrete (NAC) was also studied. The results show that the BFEM can be used to analyze the dynamic mechanical properties of RAC and NAC under high strain rate, and can be used for large-scale engineering calculations.

Analysis of Microstructure of Interfacial Transition Zone (ITZ) in Recycled Aggregate Concrete

2013 ◽  
Vol 811 ◽  
pp. 249-253 ◽  
Author(s):  
Wei Li ◽  
Hai Ying Zhang
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Interfacial Structure ◽  
Recycled Aggregate ◽  
Concrete Aggregate ◽  
Interfacial Zone ◽  
Aggregate Concrete ◽  
Mortar Strength

Experiments on influence of species of aggregate and mixing method on interfacial zone in recycled aggregate concrete were investigated. SEM observations revealed that a recycle normal-strength concrete aggregate consist of loose and porous interfacial structure, whereas a recycled high performance concrete (HPC) aggregate and a triple mixing (TM) consist mainly of dense hydrates. Various admixtures on ITZ was produced that consumed CH in the pore, modified attached cement mortar. Strength of recycled concrete was explained by interaction between cements paste and recycled aggregate. The result verified that the relatively dense pore structure of the recycled concrete benefit to development of mechanical properties.

scholarly journals Basic Mechanical Properties of Basalt Fiber Reinforced Recycled Aggregate Concrete

2017 ◽  
Vol 11 (1) ◽  
pp. 43-53 ◽  
Author(s):  
Huaxin Liu ◽  
Jianwei Yang ◽  
Xiangqing Kong ◽  
Xuxu Xue
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Basalt Fiber ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Mixing Ratio ◽  
Fiber Reinforced ◽  
Aggregate Concrete ◽  
Chopped Basalt Fiber

In order to study the basic mechanical properties of basalt fiber reinforced recycled aggregate concrete, the concrete mix ratio, the length and the volume mixing ratio of chopped basalt fiber yarn are designed for changing factors. A total of 324 specimens have been completed for this investigation. The compressive strength, splitting tensile strength, elastic modulus and axial compressive strength of basalt fiber recycled concrete have carried on the experimental study and theoretical analysis as 81 specimens, respectively. In all specimens, coarse aggregate were replaced by recycled aggregate with a replacement rate of 100%. Experimental results show that the failure process and failure pattern of basalt fiber recycled concrete and ordinary concrete are similar; With the improvement of concrete strength grade; When the volume mixing ratio of chopped basalt fiber yarn is 0.2%, the mechanic performance can effectively improve, and the length of chopped basalt fiber has less effect on the mechanical indexes; The conversion relation between common concrete mechanics index is no longer suitable for basalt fiber recycled concrete, new conversion formulas for basalt fiber recycled concrete between the mechanics index were presented through fitting experimental data.

scholarly journals Mechanical Properties of Recycled Aggregate Concrete at Low and High Water/Binder Ratios

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Gai-Fei Peng ◽  
Yan-Zhu Huang ◽  
Hai-Sheng Wang ◽  
Jiu-Feng Zhang ◽  
Qi-Bing Liu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fracture Energy ◽  
Main Type ◽  
High Water ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Heating Process ◽  
Aggregate Concrete

This paper presents an experimental research on mechanical properties of recycled aggregate concrete (RAC) at low and high water/binder (W/B) ratios. Concrete at two W/B ratios (0.255 and 0.586) was broken into recycled concrete aggregates (RCA). A type of thermal treatment was employed to remove mortar attached to RCA. The RAC at a certain (low or high) W/B ratio was prepared with RCA made from demolished concrete of the same W/B ratio. Tests were conducted on aggregate to measure water absorption and crushing values and on both RAC and natural aggregate concrete (NAC) to measure compressive strength, tensile splitting strength, and fracture energy. The mechanical properties of RAC were lower than those of NAC at an identical mix proportion. Moreover, the heating process caused a decrease in compressive strength and fracture energy in the case of low W/B ratio but caused an increase in those properties in the case of high W/B ratio. The main type of flaw in RCA from concrete at a low W/B ratio should be microcracks in gravel, and the main type of flaw in RCA from concrete at a high W/B ratio should be attached mortar.

scholarly journals Utilization of Demolished Waste as Coarse Aggregate in Concrete

2019 ◽  
Vol 5 (3) ◽  
pp. 540 ◽  
Author(s):  
Abdulsamee M Halahla ◽  
Mohammad Akhtar ◽  
Amin H. Almasri
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Recycled Concrete ◽  
International Standards ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Test Results ◽  
Aggregate Concrete ◽  
Natural Aggregate ◽  
Concrete Building

Demolishing concrete building usually produces huge amounts of remains and wastes worldwide that have promising possibilities to be utilized as coarse aggregate for new mixes of concrete. High numbers of structures around the world currently need to be removed for several reasons, such as reaching the end of the expected life, to be replaced by new investments, or were not built by the local and international standards. Maintaining or removal of such structures leads to large quantities of concrete ruins. Reusing these concrete wastes will help in saving landfill spaces in addition to more sustainability in natural resources. The objective of this study is to investigate the possibility of using old recycled concrete as coarse aggregate to make new concrete mixes, and its effect on the evolution of the compressive strength of the new concrete mixes.  Core samples for demolished concrete were tested to determine its compressive strength. The core test results can be thought of as aggregate properties for the new concrete. Then, the compressive strength and splitting tensile strength of the new recycled aggregate concrete (RAC) were determined experimentally by casting a cubes and cylinders, respectively. It was found that the evolution of compressive strength of recycled aggregate concrete is similar in behavior to the concrete with natural aggregate, except that it is about 10% lower in values. It was also seen that water absorption for recycled aggregate is noticeably higher than that for natural aggregate, and should be substituted for in the mix design.

scholarly journals Mechanical Property Tests and Strength Formulas of Basalt Fiber Reinforced Recycled Aggregate Concrete

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1851 ◽  
Author(s):  
Sheng-En Fang ◽  
Hua-Shan Hong ◽  
Pei-Hui Zhang
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Failure Modes ◽  
Volume Fraction ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Test Results ◽  
Fiber Reinforced ◽  
Aggregate Concrete ◽  
Volume Fractions

In order to investigate the influence of basalt fibers (BFs) on the mechanical performance of recycled aggregate concrete (RAC), some groups of RAC specimens were first tested involving different types of fibers such as carbon fibers, steel fibers, polypropylene fibers and hybrid fibers. The main four indices for the investigation consisted of cube compressive strengths, axial compressive strengths, splitting tensile strengths and Young’s modulus. The effects of fiber volume fractions on the RAC slumps were also discussed. Meanwhile, the mechanical properties and failure modes of the BF-reinforced RAC were compared with those of other fiber-reinforced RAC and common concrete (CC). Subsequently the optimal volume fractions of BFs were explored for different mechanical properties within the volume fraction range of 0–0.2%. The back propagation neural networks were further applied to predict and validate the optimal BF fractions. Lastly, the general strength formulas, as well as the elastic modulus formula, for BF-reinforced RAC were deducted based on the specimen test results. It is found that the addition of fibers may improve the failure modes of RAC and different fibers present positive or negative effects on the mechanical properties. The optimal volume fractions of BF with respect to the four mechanical indices are 0.1%, 0.15%, 0.1% and 0.2% respectively. The proposed strength and elastic modulus formulas of BF-reinforced RAC provide satisfactory predictions with the test results and thus can be used as a reference in practice.

scholarly journals Prediction of Shear Strength of Reinforced Recycled Aggregate Concrete Beams without Stirrups

Buildings ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 402
Author(s):  
Monthian Setkit ◽  
Satjapan Leelatanon ◽  
Thanongsak Imjai ◽  
Reyes Garcia ◽  
Suchart Limkatanyu
Keyword(s):  
Shear Strength ◽  
Shear Failure ◽  
Concrete Beams ◽  
Reduction Factor ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Shear Stresses ◽  
Test Results ◽  
Aggregate Concrete ◽  
Effective Depth

For decades, recycled coarse aggregate (RCA) has been used to make recycled aggregate concrete (RAC). Numerous studies have compared the mechanical properties and durability of recycled aggregate concrete (RAC) to those of natural aggregate concrete (NAC). However, test results on the shear strength of reinforced recycled aggregate concrete beams are still limited and sometimes contradictory. Shear failure is generally brittle and must be prevented. This article studies experimentally and analytically the shear strength of reinforced RAC beams without stirrups. Eight RAC beams and two controlled NAC beams were tested under the four-point flexural test with the shear span-to-effective depth ratio (a/d) of 3.10. The main parameters investigated were the replacement percentage of RCA (0%, 25%, 50%, 75%, and 100%) and longitudinal reinforcement ratio (ρw) of 1.16% and 1.81%. It was found that the normalized shear stresses of RAC beams with ρw = 1.81% at all levels of replacement percentage were quite similar to those of the NAC counterparts. Moreover, the normalized shear stress of the beam with 100% RCA and ρw = 1.16% was only 6% lower than that of the NAC beam. A database of 128 RAC beams without shear reinforcement from literature was analyzed to evaluate the accuracy of the ACI 318-19 shear provisions in predicting the shear strength of the beams. For an RCA replacement ratio of between 50% and 100%, it was proposed to apply a reduction factor of 0.75 to the current ACI code equation to account for the physical variations of RCA, such as replacement percentage, RCA source and quality, density, amount of residual mortar, and physical irregularity.

Sign in / Sign up

Export Citation Format

Share Document