The Forced Response Analysis of Heavy Duty Vehicle’s Cab

2014 ◽  
Vol 599-601 ◽  
pp. 503-506
Author(s):  
Jun Liang Liu ◽  
Yu Hong Long ◽  
Wen Shang Li ◽  
Jie Cai
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Theoretical Basis ◽  
Element Model ◽  
Forced Response ◽  
Response Analysis ◽  
Heavy Duty ◽  
Inherent Frequency ◽  
The Impact ◽  
Response Region

An automobile will sustain various incentives from the outside and inside in the process of being driven, in which the impact of the wheel and the vibration of engine mainly dominates. This paper gets the inherent frequency through modal analysis on finite element model in a heavy vehicle’s driving cab. And then it conducts the forced response analysis on finite element model by modeling a condition where the vibration of driving cab is caused by outside incentive. Through analyzing, it finds the main response region generated in driving cab when affected by outside incentive. At the same time, it can provide certain theoretical basis for controlling the noise of driving cab in the future.

Numerical analysis of collision between a tractor-trailer and bridge pier

2018 ◽  
Vol 9 (4) ◽  
pp. 484-503 ◽  
Author(s):  
Luwei Chen ◽  
Hao Wu ◽  
Qin Fang ◽  
Tao Zhang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Impact Force ◽  
Element Model ◽  
Bridge Pier ◽  
Bridge Piers ◽  
Highway Bridge ◽  
Heavy Duty ◽  
The Impact ◽  
The Finite Element Model

Accidents involving collisions of heavy-duty trucks with highway bridge piers occurred occasionally, in which the bridge piers might be subjected to severe damage, and cause the collapse of the superstructure due to the loss of axial loading capacity. The existing researches are mostly concentrated on the light- or medium-duty trucks. This article mainly concerns about the collisions between the heavy-duty trucks (e.g. tractor-trailer) and bridge piers as well as the evaluation of the impact force. First, by modifying the finite element model of Ford F800 single-unit truck, which was developed by National Crash Analysis Center, the finite element model of a tractor-trailer is established. Then, the full-scale tractor-trailer crash test on concrete-filled steel pier jointly conducted by Texas Transportation Institute, Federal Highway Administration, and Texas Department of Transportation is numerically simulated. The impact process is well reproduced and the established model is validated by comparison of the impact force. It indicates that the tractor-trailer impact force time history consists of two or three peaks and the corresponding causes are revealed. Furthermore, the parametric influences on the impact force are discussed, including the diameter and cross section shape of the pier, cargo weight, impact velocity, relative impact position, and vehicle type. Finally, the finite element model of an actual reinforced concrete highway bridge pier is established, and the impact force and lateral displacement of the pier subjected to the impact of the tractor-trailer are numerically derived and discussed.

Behavior of Structures Using Simple Plastic Hinge Theory

1994 ◽  
Author(s):  
Ramakrishnan Maruthayappan ◽  
Hamid M. Lankarani
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Cantilever Beam ◽  
Reliable Method ◽  
Plastic Hinge ◽  
Element Model ◽  
Finite Element Models ◽  
Computational Program ◽  
Hinge Model ◽  
The Impact

Abstract The behavior of structures under the impact or crash situations demands an efficient modeling of the system for its behavior to be predicted close to practical situations. The various formulations that are possible to model such systems are spring mass models, finite element models and plastic hinge models. Of these three techniques, the plastic hinge theory offers a more accurate model compared to the spring mass formulation and is much simpler than the finite element models. Therefore, it is desired to model the structure using plastic hinges and to use a computational program to predict the behavior of structures. In this paper, the behavior of some simple structures, ranging from an elementary cantilever beam to a torque box are predicted. It is also shown that the plastic hinge theory is a reliable method by comparing the results obtained from a plastic hinge model of an aviation seat structure with that obtained from a finite element model.

scholarly journals Design optimization of vehicle asynchronous motors based on fractional harmonic response analysis

2021 ◽  
Vol 12 (1) ◽  
pp. 689-700
Author(s):  
Ao Lei ◽  
Chuan-Xue Song ◽  
Yu-Long Lei ◽  
Yao Fu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Natural Frequency ◽  
Asynchronous Motor ◽  
Element Model ◽  
Design Parameters ◽  
Response Analysis ◽  
Harmonic Response ◽  
First Order ◽  
Harmonic Response Analysis

Abstract. To make vehicles more reliable and efficient, many researchers have tried to improve the rotor performance. Although certain achievements have been made, the previous finite element model did not reflect the historical process of the motor rotor well, and the rigidity and mass in rotor optimization are less discussed together. This paper firstly introduces fractional order into a finite element model to conduct the harmonic response analysis. Then, we propose an optimal design framework of a rotor. In the framework, objective functions of rigidity and mass are defined, and the relationship between high rigidity and the first-order frequency is discussed. In order to find the optimal values, an accelerated optimization method based on response surface (ARSO) is proposed to find the suitable design parameters of rigidity and mass. Because the higher rigidity can be transformed into the first-order natural frequency by objective function, this paper analyzes the first-order frequency and mass of a motor rotor in the experiment. The results proved that not only is the fractional model effective, but also the ARSO can optimize the rotor structure. The first-order natural frequency of asynchronous motor rotor is increased by 11.2 %, and the mass is reduced by 13.8 %, which can realize high stiffness and light mass of asynchronous motor rotors.

Experimentally validated predictive finite element modeling of the V0-V100 probabilistic penetration response of a Kevlar fabric against a spherical projectile

2018 ◽  
Vol 9 (4) ◽  
pp. 504-524 ◽  
Author(s):  
Gaurav Nilakantan
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Modeling ◽  
Element Model ◽  
Ballistic Impact ◽  
Impact Testing ◽  
Woven Fabric ◽  
Projectile Impact ◽  
Element Modeling ◽  
The Impact

This work presents the first fully validated and predictive finite element modeling framework to generate the probabilistic penetration response of an aramid woven fabric subjected to ballistic impact. This response is defined by a V0-V100 curve that describes the probability of complete fabric penetration as a function of projectile impact velocity. The exemplar case considered in this article comprises a single-layer, fully clamped, plain-weave Kevlar fabric impacted at the center by a 0.22 cal spherical steel projectile. The fabric finite element model comprises individually modeled three-dimensional warp and fill yarns and is validated against the experimental material microstructure. Sources of statistical variability including yarn strength and modulus, inter-yarn friction, and precise projectile impact location are mapped into the finite element model. A series of impact simulations at varying projectile impact velocities is executed using LS-DYNA on the fabric models, each comprising unique mappings. The impact velocities and outcomes (penetration, non-penetration) are used to generate the numerical V0-V100 curve which is then validated against the experimental V0-V100 curve obtained from ballistic impact testing and shown to be in excellent agreement. The experimental data and its statistical analysis used for model input and validation, namely, the Kevlar yarn tensile strengths and moduli, inter-yarn friction, and fabric ballistic impact testing, are also reported.

Biomechanical Comparison of Real World Concussive Impacts in Children, Adolescents, and Adults

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Lauren Dawson ◽  
David Koncan ◽  
Andrew Post ◽  
Roger Zemek ◽  
Michael D. Gilchrist ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Brain Tissue ◽  
Dynamic Models ◽  
Element Model ◽  
Tissue Response ◽  
Model Simulations ◽  
Child Group ◽  
Adolescents And Adults ◽  
The Impact

Abstract Accidental falls occur to people of all ages, with some resulting in concussive injury. At present, it is unknown whether children and adolescents are at a comparable risk of sustaining a concussion compared to adults. This study reconstructed the impact kinematics of concussive falls for children, adolescents, and adults and simulated the associated brain tissue deformations. Patients included in this study were diagnosed with a concussion as defined by the Zurich Consensus guidelines. Eleven child, 10 adolescent, and 11 adult falls were simulated using mathematical dynamic models(MADYMO), with three ellipsoid pedestrian models sized to each age group. Laboratory impact reconstruction was conducted using Hybrid III head forms, with finite element model simulations of the brain tissue response using recorded impact kinematics from the reconstructions. The results of the child group showed lower responses than the adolescent group for impact variables of impact velocity, peak linear acceleration, and peak rotational acceleration but no statistical differences existed for any other groups. Finite element model simulations showed the child group to have lower strain values than both the adolescent and adult groups. There were no statistical differences between the adolescent and adult groups for any variables examined in this study. With the cases included in this study, young children sustained concussive injuries at lower modeled brain strains than adolescents and adults, supporting the theory that children may be more susceptible to concussive impacts than adolescents or adults.

scholarly journals Characterization of Adhesives Bonding in Aircraft Structures

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4816
Author(s):  
Maria Grazia Romano ◽  
Michele Guida ◽  
Francesco Marulo ◽  
Michela Giugliano Auricchio ◽  
Salvatore Russo
Keyword(s):  
Finite Element ◽  
Composite Material ◽  
Finite Element Model ◽  
Impact Energy ◽  
Element Model ◽  
Cohesive Zone Modeling ◽  
Main Task ◽  
Opening Displacement ◽  
Lap Shear ◽  
The Impact

Structural adhesives play an important role in aerospace manufacturing, since they provide fewer points of stress concentration compared to faster joints. The importance of adhesives in aerospace is increasing significantly because composites are being adopted to reduce weight and manufacturing costs. Furthermore, adhesive joints are also studied to determine the crashworthiness of airframe structure, where the main task for the adhesive is not to dissipate the impact energy, but to keep joint integrity so that the impact energy can be consumed by plastic work. Starting from an extensive campaign of experimental tests, a finite element model and a methodology are implemented to develop an accurate adhesive model in a single lap shear configuration. A single lap joint finite element model is built by MSC Apex, defining two specimens of composite material connected to each other by means of an adhesive; by the Digimat multi-scale modeling solution, the composite material is treated; and finally, by MSC’s Marc, the adhesive material is characterized as a cohesive applying the Cohesive Zone Modeling theory. The objective was to determine an appropriate methodology to predict interlaminar crack growth in composite laminates, defining the mixed mode traction separation law variability in function of the cohesive energy (Gc), the ratio between the shear strength τ and the tensile strength σ (β1), and the critical opening displacement υc.

Structural Optimization Scheme for Horizontal Filtering Tank

2014 ◽  
Vol 577 ◽  
pp. 310-313
Author(s):  
Ping Yang ◽  
Zhou De Qu ◽  
Min Li
Keyword(s):  
Finite Element ◽  
Optimal Design ◽  
Finite Element Model ◽  
Element Model ◽  
Structural Instability ◽  
Optimization Scheme ◽  
Design Scheme ◽  
Operation Process ◽  
The Impact ◽  
The Finite Element Model

Based on the impact of some horizontal filtering tank’s instability in operation process on production, the present paper discusses the optimal design scheme for horizontal filtering tank structure with the help of finite element. Theoretical guidance will be given to enterprise from the perspective of finite element for the purpose of improving the horizontal filtering tank through constructing the finite element model for horizontal filtering tank with Creo parametric software, conducting simulation with workbench software[1] and finally arriving at the reasonable design scheme after analysis, thus avoiding the structural instability caused by the over-constraint of structural leg support beam and filter plate under-constraint.

Sign in / Sign up

Export Citation Format

Share Document