Tool Life and Wear Mechanism when Machining LM6 Aluminium (MMC) with Coated and Uncoated High Speed Steel

2015 ◽  
Vol 761 ◽  
pp. 262-266
Author(s):  
A. Siti Sarah ◽  
A.B. Mohd Hadzley ◽  
Raja Izamshah ◽  
Abu Abdullah
Keyword(s):  
Tool Life ◽  
Feed Rate ◽  
High Speed ◽  
Adhesive Wear ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Radial Depth ◽  
Titanium Aluminium

This paper aims to study the tool life of coated and uncoated high speed steel (HSS) when machining LM6 aluminium. The experiment was carried out in dry condition with spindle speed of 5000 rpm and 6000 rpm, and feed rate of 90 mm/min and 120 mm/min. Axial and radial depth of cut remain constant at 0.5 mm and 1.0 mm, respectively during the experiment. Throughout the experiments, coated HSS showed higher tool life as compared to uncoated HSS due to the coating layer of titanium aluminium nitride (TiAlN) provides protection from rapid wear during machining. For both cutting tools, the optimum cutting parameter was recorded at 5000 rpm spindle speed, 90 mm/min feed rate, 0.5 mm axial depth of cut and 1.0 mm radial depth of cut. Some evidence of built up edge (BUE) formation were observed at most of cutting tools, showing the dominant wear mechanisms appear to be adhesive wear.

The Influence of Copy Strategy on the Tool Life of Ball End Mills and Achieved Surface Roughness

2016 ◽  
Vol 686 ◽  
pp. 240-245
Author(s):  
Tomáš Vopát ◽  
Jozef Peterka ◽  
Vladimír Šimna ◽  
Ivan Buranský
Keyword(s):  
Surface Roughness ◽  
Tool Life ◽  
High Speed ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Tool Material ◽  
High Speed Steel ◽  
Depth Of Cut ◽  
Radial Depth ◽  
End Mills

The article deals with the tool life of ball nose end mills and surface roughness of steel C45 depending on up-copying and down-copying. The cemented carbide and high speed steel was used as tool material. Furthermore, the new and sharpened cutting tools were also compared. In the experiment, the cutting speed, feed rate, axial and radial depth of cut were not changed. The results show different achieved surface roughness of machined material C45 and tool life of ball nose end mills depending on the copy milling strategy for various tool materials.

scholarly journals Tool Wear and Surface Evaluation in Drilling Fly Ash Geopolymer Using HSS, HSS-Co, and HSS-TiN Cutting Tools

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1628
Author(s):  
Mohd Fathullah Ghazali ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Shayfull Zamree Abd Rahim ◽  
Joanna Gondro ◽  
Paweł Pietrusiewicz ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Tool Life ◽  
High Speed ◽  
Flank Wear ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Spindle Speed ◽  
Drilling Process ◽  
Potential Use

This paper reports on the potential use of geopolymer in the drilling process, with respect to tool wear and surface roughness. The objectives of this research are to analyze the tool life of three different economy-grade drill bit uncoated; high-speed steel (HSS), HSS coated with TiN (HSS-TiN), and HSS-cobalt (HSS-Co) in the drilling of geopolymer and to investigate the effect of spindle speed towards the tool life and surface roughness. It was found that, based on the range of parameters set in this experiment, the spindle speed is directly proportional to the tool wear and inversely proportional to surface roughness. It was also observed that HSS-Co produced the lowest value of surface roughness compared to HSS-TiN and uncoated HSS and therefore is the most favorable tool to be used for drilling the material. For HSS, HSS coated with TiN, and HSS-Co, only the drilling with the spindle speed of 100 rpm was able to drill 15 holes without surpassing the maximum tool wear of 0.10 mm. HSS-Co exhibits the greatest tool life by showing the lowest value of flank wear and produce a better surface finish to the sample by a low value of surface roughness value (Ra). This finding explains that geopolymer is possible to be drilled, and therefore, ranges of cutting tools and parameters suggested can be a guideline for researchers and manufacturers to drill geopolymer for further applications.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

Investigation of Surface Roughness and Material Removal Rate for High Speed Micro End Milling on PMMA

2015 ◽  
Vol 1115 ◽  
pp. 12-15
Author(s):  
Nur Atiqah ◽  
Mohammad Yeakub Ali ◽  
Abdul Rahman Mohamed ◽  
Md. Sazzad Hossein Chowdhury
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
High Speed ◽  
End Milling ◽  
Removal Rate ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Micro End Milling

Micro end milling is one of the most important micromachining process and widely used for producing miniaturized components with high accuracy and surface finish. This paper present the influence of three micro end milling process parameters; spindle speed, feed rate, and depth of cut on surface roughness (Ra) and material removal rate (MRR). The machining was performed using multi-process micro machine tools (DT-110 Mikrotools Inc., Singapore) with poly methyl methacrylate (PMMA) as the workpiece and tungsten carbide as its tool. To develop the mathematical model for the responses in high speed micro end milling machining, Taguchi design has been used to design the experiment by using the orthogonal array of three levels L18 (21×37). The developed models were used for multiple response optimizations by desirability function approach to obtain minimum Ra and maximum MRR. The optimized values of Ra and MRR were 128.24 nm, and 0.0463 mg/min, respectively obtained at spindle speed of 30000 rpm, feed rate of 2.65 mm/min, and depth of cut of 40 μm. The analysis of variance revealed that spindle speeds are the most influential parameters on Ra. The optimization of MRR is mostly influence by feed rate. Keywords:Micromilling,surfaceroughness,MRR,PMMA

SURFACE ROUGHNESS OF MAGNESIUM ALLOY AZ91D IN HIGH SPEED MILLING

2016 ◽  
Vol 78 (6-9) ◽  
Author(s):  
Mohd Shahfizal Ruslan ◽  
Kamal Othman ◽  
Jaharah A.Ghani ◽  
Mohd Shahir Kassim ◽  
Che Hassan Che Haron
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Parameters ◽  
Experimental Result ◽  
Depth Of Cut ◽  
Polishing Process ◽  
High Speed Cutting ◽  
Radial Depth

Magnesium alloy is a material with a high strength to weight ratio and is suitable for various applications such as in automotive, aerospace, electronics, industrial, biomedical and sports. Most end products require a mirror-like finish, therefore, this paper will present how a mirror-like finishing can be achieved using a high speed face milling that is equivalent to the manual polishing process. The high speed cutting regime for magnesium alloy was studied at the range of 900-1400 m/min, and the feed rate for finishing at 0.03-0.09 mm/tooth. The surface roughness found for this range of cutting parameters were between 0.061-0.133 µm, which is less than the 0.5µm that can be obtained by manual polishing. Furthermore, from the S/N ratio plots, the optimum cutting condition for the surface roughness can be achieved at a cutting speed of 1100 m/min, feed rate 0.03 mm/tooth, axial depth of cut of 0.20 mm and radial depth of cut of 10 mm. From the experimental result the lowest surface roughness of 0.061µm was obtained at 900 m/min with the same conditions for other cutting parameters. This study revealed that by milling AZ91D at a high speed cutting, it is possible to eliminate the polishing process to achieve a mirror-like finishing.

Development of Tooling Cost Model for High Speed Hard Turning

2011 ◽  
Vol 418-420 ◽  
pp. 1482-1485 ◽  
Author(s):  
Erry Yulian Triblas Adesta ◽  
Muataz Al Hazza ◽  
Delvis Agusman ◽  
Agus Geter Edy Sutjipto
Keyword(s):  
Feed Rate ◽  
High Speed ◽  
Hard Turning ◽  
Cost Model ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Depth Of Cut ◽  
Predictive Regression ◽  
Aisi 4340

The current work presents the development of cost model for tooling during high speed hard turning of AISI 4340 hardened steel using regression analysis. A set of experimental data using ceramic cutting tools, composed approximately of Al2O3 (70%) and TiC (30%) on AISI 4340 heat treated to a hardness of 60 HRC was obtained in the following design boundary: cutting speeds (175-325 m/min), feed rate (0.075-0.125 m/rev), negative rake angle (0 to -12) and depth of cut of (0.1-0.15) mm. The output data is used to develop a new model in predicting the tooling cost using in terms of cutting speed, feed rate, depth of cut and rake angle. Box Behnken Design was used in developing the model. Predictive regression model was found to be capable of good predictions the tooling cost within the boundary design.

scholarly journals Tribological properties of ion-modified composite coatings

2021 ◽  
Vol 2059 (1) ◽  
pp. 012015
Author(s):  
M Sh Migranov ◽  
A M Migranov ◽  
S R Shekhtman
Keyword(s):  
Wear Resistance ◽  
Tool Life ◽  
High Speed ◽  
Composite Coatings ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Hard Coating ◽  
Ion Nitriding ◽  
Additional Layer ◽  
Nitrided Surface

Abstract The paper presents the results of a study of one of the ways to increase the wear resistance of “duplex” coatings applied to cutting tools, which are due to preliminary diffusion saturation of the tool surface with nitrogen (known as ion nitriding) followed by physical deposition of a hard coating (Ti, Cr) N. The proposed coating also contains an additional layer with an impurity of ions, deposited on a preliminary nitrided surface of high speed steel before the deposition of a hard coating. Tests were carried out to evaluate the effect of these modified layers on the tool life of the HSS tool. The greatest wear resistance after "triplex" - treatment was achieved during ion implantation of titanium into a pre-nitrided surface. The coefficient of friction of the modified layer was studied at different contact temperatures. Ionic mixing contributes to the appearance of a thin surface layer with an amorphous-like structure, which prolongs the stage of normal wear, which significantly increases the tool life as a result of the self-organization process.

Tool Wear Characteristics in High Speed Milling of Ti-6Al-4V Alloy with Nitrogen Gas Medium

2006 ◽  
Vol 315-316 ◽  
pp. 588-592 ◽  
Author(s):  
Wei Zhao ◽  
Ning He ◽  
Liang Li ◽  
Z.L. Man
Keyword(s):  
Tool Wear ◽  
High Speed ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth ◽  
Oil Mist ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes

High speed milling experiments using nitrogen-oil-mist as cutting medium were undertaken to investigate the characteristics of tool wear for Ti-6Al-4V Alloy, a kind of important and commonly used titanium alloy in the aerospace and automobile industries. Uncoated carbide tools have been applied in the experiments. The cutting speed was 300 m/min. The axial depth of cut and the radial depth of cut were kept constant at 5.0 mm and 1.0 mm, respectively. The feed per tooth was 0.1 mm/z. Optical and scanning electron microscopes have been utilized to determine the wear mechanisms of the cutting tools, and energy spectrum analysis has been carried out to measure the elements distribution at the worn areas. Meanwhile, comparisons were made to discuss the influence of different cutting media such as nitrogen-oil-mist and air-oil–mist upon the tool wear. The results of this investigation indicate that the tool life in nitrogen-oil-mist is significantly longer than that in air-oil-mist, and nitrogen-oil-mist is more suitable for high speed milling of Ti-6Al-4V alloy than air-oil-mist.

scholarly journals Optimization of Boring Process Parameters in Manufacturing of Polyacetal Bushing using High Speed Steel

2019 ◽  
Vol 130 ◽  
pp. 01031 ◽  
Author(s):  
The Jaya Suteja ◽  
Yon Haryono ◽  
Andri Harianto ◽  
Esti Rinawiyanti
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Feed Rate ◽  
High Speed ◽  
Removal Rate ◽  
High Speed Steel ◽  
Cutting Edge ◽  
Depth Of Cut ◽  
Optimum Result ◽  
Edge Angle

Polyacetal is commonly used as bushing material because of its low coefficient of friction and self lubricant characteristics. The polyacetal is machined by using boring process to produce bushing in certain surface roughness. The objectives of this research are to optimize three independent parameters (depth of cut, feed rate and principal cutting edge angle) of boring process of polyacetal using high speed steel tool to achieve the highest material removal rate and the required surface roughness. Response Surface Methodology is used to investigate the influence of the parameters and optimize the boring process. The research shows that the influence of the boring process parameters on polyacetal is similar compared to on metal. The result reveals that the optimum result is achieved by applying the value of depth of cut, feed rate, and principal cutting edge angle is 2.9 × 10–3 m, 0.229 mm rev–1, and 99.1° respectively. By applying these values, the maximum material rate removal achieved in this research is 1263.4 mm3 s–1 and the surface roughness achieved is 1.57 × 10–6 m.

Tool life prediction by RSM for cryogenic milling of inconel 718

2019 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Nurul Hayati Binti Abdul Halim ◽  
Che Hassan Che Haron ◽  
Jaharah A. Ghani ◽  
Muammar Faiq Azhar
Keyword(s):  
Tool Life ◽  
Inconel 718 ◽  
High Speed ◽  
Metal Cutting ◽  
Milling Process ◽  
Average Error ◽  
Depth Of Cut ◽  
Content Type ◽  
Radial Depth ◽  
Ball Nose Milling

Purpose The purpose of this study is to present the tool life optimization of carbide-coated ball nose milling inserts when high-speed milling of Inconel 718 under cryogenic CO2 condition. The main aims are to analyze the influence level of each cutting parameter on the tool life and to identify the optimum parameters that can lengthen the tool life to the maximum. Design/methodology/approach The experimental layout was designed using Box–Behnken RSM where all parameters were arranged without combining their highest and lowest values of each factor at the same time. A total of 29 milling experiments were conducted. Then, a statistical analysis using ANOVA was conducted to identify the relationship between the controlled factors on tool life. After that, a predictive model was developed to predict the variation of tool life within the predetermined parameters. Findings Results from the experimental found that the longest tool life of 22.77 min was achieved at Vc: 120 m/min, fz: 0.2 mm/tooth, ap: 0.5 mm and ae: 0.2 mm. ANOVA suggests the tool life of 23.4 min can be reached at Vc: 120.06 m/min, fz: 0.15 mm/tooth, ap: 0.66 mm and ae: 0.53 mm. All four controlled factors have influenced the tool life with the feed rate and radial depth of cut (DOC) as the major contributors. The developed mathematical model accurately represented the tool life at an average error of 8.2 per cent when compared to the actual and predicted tool life. Originality/value These experimental and statistical studies were conducted using Box–Behnken RSM method under cryogenic CO2 condition. It is a proven well-known method. However, the cooling method used in this study is a new technique and its effects on metal cutting, especially in the milling process of Inconel 718, has not yet been explored.

Sign in / Sign up

Export Citation Format

Share Document