scholarly journals Numerical Simulation on End Suction Centrifugal Pump Running in Inverse Flow for Microhydro Applications

2015 ◽  
Vol 773-774 ◽  
pp. 358-362 ◽  
Author(s):  
Mohd Azlan Ismail ◽  
Al Khalid Othman ◽  
Hushairi Zen
Keyword(s):  
Rural Communities ◽  
Centrifugal Pump ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Tetrahedral Mesh ◽  
Hydraulic Characteristics ◽  
Complex Flow ◽  
Steady State Condition ◽  
Performance Curves ◽  
Flow Domain

The initial capital cost for most microhydro projects has always been an overriding issue for self-funded remote communities. The cost will escalate significantly in the absence of local microhydro electromechanical manufacturers. The application of end suction centrifugal pump as turbine will reduce the overall cost, which renders microhydro systems feasible for self-funded projects and are therefore suitable for rural communities. The goal of this study is to design and develop a pump as turbine (PAT) which serves as a substitute to commercial electromechanical components. Numerical analysis of an inverse flow for an end suction centrifugal pump is presented in this paper, which includes the performance curves and hydraulic characteristics of the pump. ANSYS CFX, a commercial CFD software is used to simulate the performance of the pump with specific speed, Ns of 70 units (Euroflo EU50-20). The computational flow domain inside the pump is comprises of impeller, volute and draft tube. Unstructured tetrahedral mesh is used to maintain good surface mesh due to complex flow domain geometries. The governing equations used in the simulations are three-dimensional, incompressible Navier-Stokes and k-ϵ turbulence model under steady-state condition. The simulation results are compared with pump performance curve supplied by the pump manufacturer. The verification results show good agreement for flow rates between 0.7 and 1.3 QBEP. The best efficient point (BEP) for inverse flow is attained at a higher head and flow rate compared to pump mode, whereby the value is found to be 21.55 m and 14.0 l/s, respectively. It is believed that the findings of this study will be useful to predict hydraulic characteristics and performance curves of PAT and the model may be used to identify poor flow characteristics inside the pump. It is recommended that optimization process is carried out using CFD tools in future studies.

Flow Characteristics in a Three-Dimensional Rectangular Channel With a Pair of Ribs Placed Symmetrically at the Channel Walls

2000 ◽  
Author(s):  
M. Singh ◽  
P. K. Panigrahi ◽  
G. Biswas
Keyword(s):  
Heat Transfer ◽  
Large Scale ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Navier Stokes ◽  
Complex Flow ◽  
Energy Equations

Abstract A numerical study of rib augmented cooling of turbine blades is reported in this paper. The time-dependent velocity field around a pair of symmetrically placed ribs on the walls of a three-dimensional rectangular channel was studied by use of a modified version of Marker-And-Cell algorithm to solve the unsteady incompressible Navier-Stokes and energy equations. The flow structures are presented with the help of instantaneous velocity vector and vorticity fields, FFT and time averaged and rms values of components of velocity. The spanwise averaged Nusselt number is found to increase at the locations of reattachment. The numerical results are compared with available numerical and experimental results. The presence of ribs leads to complex flow fields with regions of flow separation before and after the ribs. Each interruption in the flow field due to the surface mounted rib enables the velocity distribution to be more homogeneous and a new boundary layer starts developing downstream of the rib. The heat transfer is primarily enhanced due to the decrease in the thermal resistance owing to the thinner boundary layers on the interrupted surfaces. Another reason for heat transfer enhancement can be attributed to the mixing induced by large-scale structures present downstream of the separation point.

scholarly journals A Multi-GPU Parallel Algorithm in Hypersonic Flow Computations

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Jianqi Lai ◽  
Hua Li ◽  
Zhengyu Tian ◽  
Ye Zhang
Keyword(s):  
Parallel Algorithm ◽  
Hypersonic Flow ◽  
Stokes Equations ◽  
Programming Model ◽  
Graphics Processing Unit ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Time Discretization ◽  
Processing Unit ◽  
Complex Flow

Computational fluid dynamics (CFD) plays an important role in the optimal design of aircraft and the analysis of complex flow mechanisms in the aerospace domain. The graphics processing unit (GPU) has a strong floating-point operation capability and a high memory bandwidth in data parallelism, which brings great opportunities for CFD. A cell-centred finite volume method is applied to solve three-dimensional compressible Navier–Stokes equations on structured meshes with an upwind AUSM+UP numerical scheme for space discretization, and four-stage Runge–Kutta method is used for time discretization. Compute unified device architecture (CUDA) is used as a parallel computing platform and programming model for GPUs, which reduces the complexity of programming. The main purpose of this paper is to design an extremely efficient multi-GPU parallel algorithm based on MPI+CUDA to study the hypersonic flow characteristics. Solutions of hypersonic flow over an aerospace plane model are provided at different Mach numbers. The agreement between numerical computations and experimental measurements is favourable. Acceleration performance of the parallel platform is studied with single GPU, two GPUs, and four GPUs. For single GPU implementation, the speedup reaches 63 for the coarser mesh and 78 for the finest mesh. GPUs are better suited for compute-intensive tasks than traditional CPUs. For multi-GPU parallelization, the speedup of four GPUs reaches 77 for the coarser mesh and 147 for the finest mesh; this is far greater than the acceleration achieved by single GPU and two GPUs. It is prospective to apply the multi-GPU parallel algorithm to hypersonic flow computations.

scholarly journals Flow Characteristics in Volute of a Double-Suction Centrifugal Pump with Different Impeller Arrangements

Energies ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 669 ◽  
Author(s):  
Yu Song ◽  
Honggang Fan ◽  
Wei Zhang ◽  
Zhifeng Xie
Keyword(s):  
Centrifugal Pump ◽  
High Efficiency ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Weighted Average ◽  
Complex Flow ◽  
Suction Pump ◽  
Impeller Outlet ◽  
Large Flow ◽  
Dominant Frequencies

As an important type of centrifugal pump, the double-suction pump has been widely used due to its high efficiency region and large flow rate. In the present study, the complex flow in volute of a double-suction centrifugal pump is investigated by numerical simulation using a re-normalization group (RNG) k-ε model with experimental validation. Axial flows are observed in volute near the impeller outlet and compared with four staggered angles. The net area-weighted average axial velocities decrease as the staggered angle increases. The axial flows are mainly caused by the different circumferential pressure distribution at the twin impeller outlet. The dominant frequencies of the axial velocities for different staggered angles are fBP and its harmonic. The pressure fluctuations in most regions of the volute are obtained by superimposing the pressure generated by the two impellers.

Experimental and Numerical Study of Hydrodynamic Cavitation of Orifice Plates with Multiple Triangular Holes

2012 ◽  
Vol 256-259 ◽  
pp. 2519-2522 ◽  
Author(s):  
Zhi Yong Dong ◽  
Qi Qi Chen ◽  
Yong Gang Yang ◽  
Bin Shi
Keyword(s):  
Velocity Profile ◽  
High Speed ◽  
Numerical Study ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Orifice Plate ◽  
Hydrodynamic Cavitation ◽  
High Speed Photography ◽  
Hydraulic Characteristics ◽  
Image Velocimetry

Hydraulic characteristics of orifice plates with multiple triangular holes in hydrodynamic cavitation reactor were experimentally investigated by use of three dimensional particle image velocimetry (PIV), high speed photography, electronic multi-pressure scanivalve and pressure data acquisition system, and numerically simulated by CFD software Flow 3D in this paper. Effects of number, arrangement and ratio of holes on hydraulic characteristics of the orifice plates were considered. Effects of arrangement and ratio of holes and flow velocity ahead of plate on cavitation number and velocity profile were compared. Distribution of turbulent kinetic energy and similarity of velocity profile were analyzed. And characteristics of cavitating flow downstream of the orifice plate were photographically observed by high speed camera. Also, a comparison with flow characteristics of orifice plate with hybrid holes (circle, square and triangle) was made.

Effect of Baffles in Between Stages on Performance and Flow Characteristics of a Two-Stage Split Case Centrifugal Pump

2017 ◽  
Author(s):  
Yiyun Wang ◽  
Ji Pei ◽  
Shouqi Yuan ◽  
Wenjie Wang
Keyword(s):  
Centrifugal Pump ◽  
High Efficiency ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Production Method ◽  
Navier Stokes ◽  
Centrifugal Pumps ◽  
Two Stage

Two-stage split case centrifugal pumps play an important role in large flow rate and high lift water transfer situations. To investigate the influence of baffles in between stages on the performance and internal flow characteristics, the unsteady simulations for the prototype pump were carried out by solving the three-dimensional Reynolds-averaged Navier-Stokes equations with a shear stress transport (SST) turbulence model. The structured grids were generated for the whole flow passage. The calculated performance results were verified by the experimental measurements. The entropy production method based on numerical simulation was applied to analyze the distribution and mechanism of flow losses. The results show that the turbulence dissipation is the dominant flow loss, and the viscous dissipation can be neglected. The baffles can reduce the turbulence dissipation power obviously and can improve the hydraulic efficiency by maximum 5%, especially under QBEP and over-load conditions. The baffles have the greatest effect on the hydraulic losses in the double suction impeller., because they change the flow characteristics in the channels between the first stage impeller and the double suction impeller, affecting the inflow condition dramatically for the impeller. The study can give a reference to optimize the design of the two-stage split case centrifugal pump for high efficiency.

Modeling and Computation of Flow in a Passage With 360-Degree Turning and Multiple Airfoils

1993 ◽  
Vol 115 (1) ◽  
pp. 103-108 ◽  
Author(s):  
W. Shyy ◽  
T. C. Vu
Keyword(s):  
Porous Medium ◽  
Global Analysis ◽  
Flow Behavior ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Hydraulic Turbine ◽  
Complex Flow ◽  
The Individual ◽  
Spiral Casing

The spiral casing of a hydraulic turbine is a complex flow device which contains a passage of 360-degree turning and multiple elements of airfoils (the so-called distributor). A three-dimensional flow analysis has been made to predict the flow behavior inside the casing and distributor. The physical model employs a two-level approach, comprising of (1) a global model that adequately accounts for the geometry of the spiral casing but smears out the details of the distributor, and represents the multiple airfoils by a porous medium treatment, and (2) a local model that performs detailed analysis of flow in the distributor region. The global analysis supplies the inlet flow condition for the individual cascade of distributor airfoils, while the distributor analysis yields the information needed for modeling the characteristics of the porous medium. Comparisons of pressure and velocity profiles between measurement and prediction have been made to assess the validity of the present approach. Flow characteristics in the spiral casing are also discussed.

Numerical Simulation and Model Test on Hydraulic Characteristics of Long-Distance Inverted Siphon

2012 ◽  
Vol 212-213 ◽  
pp. 1131-1135 ◽  
Author(s):  
Juan Li ◽  
Zhen Wei Mu ◽  
Lin Li
Keyword(s):  
Numerical Simulation ◽  
Model Test ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Inlet Section ◽  
Hydraulic Characteristics ◽  
Filling Process ◽  
Long Distance ◽  
Three Dimensional Flow ◽  
Inverted Siphon

Make Use of three-dimensional flow field turbulence numerical simulation of unsteady flow k~εturbulence model and tracking the free surface VOF method of long-distance inverted siphon. By numerical calculation of flow characteristics and pressure distribution, carried out with the model test contrast, the results were coordinate and meet the requirements of design. But vortex formed in the filling process, it is recommended to optimize the inverted siphon inlet section. The method of combining calculation and test on the long-distance inverted siphon provide the reference for the design and operation.

CFD Analysis and Experimental Verification of Multi-Stage Centrifugal Pump with Multi-Outlet Options

2013 ◽  
Vol 331 ◽  
pp. 94-97
Author(s):  
Si Huang ◽  
Guo Wei Ou ◽  
Zhi Guang Song ◽  
Peng Wang
Keyword(s):  
Flow Field ◽  
Centrifugal Pump ◽  
Three Dimensional ◽  
Flow Simulation ◽  
Cfd Analysis ◽  
Three Dimensional Flow ◽  
Pump Performance ◽  
Field Distributions ◽  
Multi Stage ◽  
Performance Curves

A three-dimensional flow in a whole multi-stage centrifugal pump with multi-outlet options is numerically simulated using CFX software. The flow field distributions inside pump with different outlet setting are observed and analyzed. Specially, it is found that the downstream of the pump outlet is considerably different from upstream of the pump outlet and forms some self-circulating vortexes inside the stage with more energy loss. The pump performance curves are predicted based on the flow simulation, showing that efficiency rises up while the pump outlet is set at the backward stages. Finally, CFD results are verified by comparing predicted performance curves with the experimental ones.

Creation of Transparent Flow Passage to Measure the Biomedical Flow Inside Human Body by PIV

2011 ◽  
Author(s):  
Sung Kyun Kim ◽  
Anna Seo ◽  
Jiwon Jang ◽  
Kangsoo Chung
Keyword(s):  
Automatic Segmentation ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Medical Doctors ◽  
Complex Flow ◽  
Web Based ◽  
Human Organ ◽  
Flow Passage ◽  
Post Surgery ◽  
Ct Data

Knowledge of flow characteristics in human airway and blood vessel is essential to understand the physiological and pathological aspects of respiratory and circulatory systems. Creating an accurate transparent flow passage is indispensable for the successful investigation on the flow inside a complex flow passage of human organ by PIV. The Web-based communication system between multi-researchers and medical doctors is established for making the post-surgery models and to discuss surgery plans. We also introduced a semi-automatic segmentation technique to reconstruct accurate three dimensional computer models from CT data rapidly and conveniently.

scholarly journals Performance Assessment of Shockwaves of Chute Spillways in Large Dams

2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
S. M. Mousavimehr ◽  
Omid Aminoroayaie Yamini ◽  
M. R. Kavianpour
Keyword(s):  
Flow Characteristics ◽  
Hydraulic Characteristics ◽  
Effective Parameters ◽  
Aerated Flow ◽  
Large Dams ◽  
Gate Opening ◽  
Experimental Formation ◽  
Flow Domain ◽  
Available Information ◽  
The Waves

Spillways are the most important structures of large dams that are responsible for releasing the excessive flood discharge from the reservoir. Although many studies have been performed to determine the flow characteristics over these structures, however, the available information on the shockwaves’ characteristics for spillways’ design is limited. The supercritical flow below the chute piers generates an aerated flow known as shockwaves. Due to the flow interaction with the chute piers, three kinds of standing waves just downstream of the pier, in the middle of the chute, and on the sidewalls are generated. This phenomenon affects the flow domain and its hydraulic characteristics along the chute spillway. The height of the waves increases downstream, where they hit the chute walls and reflect again into the flow to interact together again. The process repeated and intensified downstream in a lozenge shape. The height of these waves can be more than twice the depth flow and thus run over the sidewalls. This is important for the design of chute walls in chute spillways with control gates. In this study, the experimental formation of the shockwaves and their behavior along the chute and their reduction measures are presented. Experiments were conducted on a scaled physical model (1/50) of Kheirabad Dam, Water Research Institute, Iran. It was realized that apart from the geometry of piers and chute spillway, Froude number of flow and gate opening are the main effective parameters on the hydraulic performance of shockwaves’ formation and their development on gated spillways.

Sign in / Sign up

Export Citation Format

Share Document