Sound-Absorbing Composites Based on Flax and Polymer Fibers

2015 ◽  
Vol 806 ◽  
pp. 161-166 ◽  
Author(s):  
Nikolay V. Yakimovich ◽  
Sergey N. Bukharov ◽  
Victor V. Kozhushko ◽  
Anastasiya S. Khmara ◽  
Vladimir P. Sergienko
Keyword(s):  
Composite Materials ◽  
Sound Absorption ◽  
Low Frequency ◽  
Single Layer ◽  
Polymer Fibers ◽  
Frequency Range ◽  
Normal Absorption

The paper considers sound absorption of the composite materials, which are based on the natural flax and polymer fibers. The thickness of a single layer of obtained nonwoven composite is about 10 mm. The analysis of absorption dependences is carried out for different thicknesses of the material. It is shown that in the low frequency range the absorption almost linearly increases depending on the thickness. The coefficient of the normal absorption increases with the frequency in the range from 50 Hz up to 1600 Hz. The hot-pressed material can be used for panel production. The sound absorption increases with the thickness of the pressed material. The measurements show the possibilities of application of the composite for the production of the parts of cabs’ interior.

Broadening of the Sound Absorption Bandwidth of the Perforated Panel Using a Membrane-Type Resonator

2018 ◽  
Vol 140 (3) ◽  
Author(s):  
Xuezhi Zhu ◽  
Zhaobo Chen ◽  
Yinghou Jiao ◽  
Yanpeng Wang
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Degrees Of Freedom ◽  
Low Frequency ◽  
Absorption Capacity ◽  
Sound Absorption Coefficient ◽  
Sound Waves ◽  
Frequency Range ◽  
Absorption Bandwidth ◽  
Membrane Type

In order to broaden the sound absorption bandwidth of a perforated panel in the low frequency range, a lightweight membrane-type resonator is installed in the back cavity of the perforated panel to combine into a compound sound absorber (CSA). Because of the great flexibility, the membrane-type resonator can be vibrated easily by the incident sound waves passing through the holes of the perforated panel. In the low frequency range, the membrane-type resonator and the perforated panel constitute a two degrees-of-freedom (DOF)-resonant type sound absorption system, which generates two sound absorption peaks. By tuning the parameters of the membrane type resonator, a wide frequency band having a large sound absorption coefficient can be obtained. In this paper, the sound absorption coefficient of CSA is derived analytically by combining the vibration equation of the membrane-type resonator with the acoustic impedance equation of the perforated panel. The influences of the parameters of the membrane-type resonator on the sound absorption performance of the CSA are numerically analyzed. Finally, the wide band sound absorption capacity of the CSA is validated by the experimental test.

A Preliminary Study on the Sound Absorption of Self-Facing Date Palm Fibers

2014 ◽  
Vol 565 ◽  
pp. 25-30 ◽  
Author(s):  
Elwaleed A. Khidir ◽  
N. Nikabdullah ◽  
M.J.M. Nor ◽  
M.F.Mat Tahir ◽  
M.Z. Nuawi
Keyword(s):  
Sound Absorption ◽  
Date Palm ◽  
Perforated Plate ◽  
Low Frequency ◽  
Single Layer ◽  
Absorption Properties ◽  
Date Palm Fibers ◽  
Layer Sample ◽  
Good Improvement ◽  
Preliminary Study

Sound absorption of self-facing natural date palm fibershas been investigated.A single layer sample of the fibers was tested for its sound absorption properties. The sample was then faced with the originally date palm fiber netted structure. Experimental measurements were conducted on the impedance tube at the acoustic lab, Faculty of Engineering, UniversitiKebangsaan Malaysia, to determine the sound absorption coefficient.The single layer was also tested using an aluminum perforated plate, as facing, for comparison purposes.The results show a good improvement in the sound absorption for the self-facing panel for the whole frequency range. However, when using the aluminum perforated panel an improvement in the sound absorption was observed only above 2500 Hz. The effect of introducing air gap thickness was studied. The results show improvement for the sound absorption the low frequency.

Analysis of Sound Absorption Properties of Three-Leaf Microperforated Panel Absorbers without a Rigid Backing

2014 ◽  
Vol 937 ◽  
pp. 465-471
Author(s):  
Xiao Ling Gai ◽  
Xian Hui Li ◽  
Rui Wu ◽  
Bin Zhang ◽  
Jun Juan Zhao
Keyword(s):  
Sound Absorption ◽  
Low Frequency ◽  
Wide Frequency Range ◽  
Structure Design ◽  
Frequency Region ◽  
Theoretical Development ◽  
Frequency Range ◽  
Absorption Properties ◽  
High Frequency Region ◽  
Energy Dissipated

Microperforated panel (MPP) absorbers have been developed rapidly and used in many fields in recent years. First, based on the Maa’s theory, the theoretical development of MPP is reviewed in this paper. Furthermore, structure design and processing technology of MPP are introduced. Finally, the further development of MPP is discussed. Based on the MPP theory and electro-acoustical equivalent circuit principle, sound absorption properties of three-leaf microperforated panel (TMPP) absorbers without a rigid backing are studied to broaden the sound absorption bandwidth of MPP structure. Simulation results show that TMPP absorbers without a rigid backing have two resonance peaks and the energy dissipated coefficient remains constant in the low frequency range. The resonance frequency moves toward low frequency region with the increasing of the distance, thickness and pore diameter of MPP and moves toward high frequency region with the increasing of the perforation when other parameters keep invariant. The energy dissipated coefficient more than 0.5 over 8 octaves by choosing proper parameters. In conclusion, TMPP absorbers without a rigid backing have good sound absorption properties in a wide frequency range.

scholarly journals Sound absorption properties of multi-layer structural composite materials based on waste corn husk fibers

2020 ◽  
Vol 15 ◽  
pp. 155892502091086
Author(s):  
Lihua Lyu ◽  
Jing Lu ◽  
Jing Guo ◽  
Yongfang Qian ◽  
Hong Li ◽  
...  
Keyword(s):  
Composite Materials ◽  
Absorption Coefficient ◽  
Sound Absorption ◽  
Low Frequency ◽  
Sound Absorption Coefficient ◽  
Absorption Properties ◽  
Cavity Depth ◽  
Air Cavity ◽  
Corn Husk ◽  
Structural Composite

In order to find a reasonable way to use the waste corn husk, waste degummed corn husk fibers were used as reinforcing material in one type of composite material. And polylactic acid particles were used as matrix material. The composite materials were prepared by mixing and hot-pressing process, and they were processed into the micro-slit panel. Then, the multi-layer structural sound absorption composite materials were prepared sequentially by micro-slit panel, air cavity, and flax felt. Finally, the sound absorption properties of the multi-layer structural composite materials were studied by changing flax felt thickness, air cavity depth, slit rate, and thickness of micro-slit panel. As the flax felt thickness varied from 0 to 10 mm in 5 mm increments, the peak of sound absorption coefficient shifted to low frequency. The sound absorption coefficient in the low frequency was improved with the air cavity depth varied from 0 to 10 mm in 5 mm increments. With the slit rate increased from 3% to 7% in 2% increments, the peak of sound absorption coefficient shifted to high frequency. With the thickness of micro-slit panel increased from 2 to 6 mm in 2 mm increments, the sound absorption bandwidth was broaden, and the peak of sound absorption coefficient was increased and shifted to low frequency. Results showed that the highest sound absorption coefficient of the multi-layer structural composite materials was about 1 under the optimal process conditions.

scholarly journals Synthesis and Evaluation of Polyurethane Foam Composites for Enhanced Sound Absorption at Low Frequency

2019 ◽  
Vol 8 (3) ◽  
pp. 6815-6818
Keyword(s):  
Absorption Coefficient ◽  
Polyurethane Foam ◽  
Sound Absorption ◽  
Low Frequency ◽  
Weight Fraction ◽  
Crumb Rubber ◽  
Polyurethane Foams ◽  
Sound Absorption Coefficient ◽  
Filler Materials ◽  
Frequency Range

Polyurethane foams are extensively used as sound absorbing materials in various automobile parts. However, the sound absorption capability of polyurethane foam ispoorin low frequency range. The advancement of technologies to develop newerpolymer composites, provide scope to develop composite polyurethane foam with better sound absorption coefficient in low frequency range. Composite foams are made with two different filler materials as crumb rubber and coconut fiber, in varying weight fraction of up to 2.0%. Density, Sound absorption coefficient, and Noise reduction, measurements were done on all polyurethane foams. The effect offiller additionsto polyurethane foams ondensity and sound absorption coefficient at low frequency are discussed.The 1.4 % crumb rubber polyurethane foam offers the best combination of low density, improved sound absorption coefficient value and noise absorption at low frequency.

scholarly journals Modifikasi Permukaan Elemen Peredam Bising Dengan Profil Berbentuk Prisma

2016 ◽  
Vol 6 (01) ◽  
Author(s):  
Hanif Azimut
Keyword(s):  
High Frequency ◽  
Sound Absorption ◽  
Coupling Effect ◽  
Low Frequency ◽  
The Other ◽  
Frequency Range ◽  
Closed Type ◽  
Wave Resonance ◽  
Half Wave ◽  
Absorption Performance

<p class="AbstractText">The influence of surface modification by using prism shaped profile on the sound absorption of absorber element was investigated experimentally. A prime number based configuration of the two types opened and closed type rism shaped profile inclusion was tested by using impedance tube according ASTM E1050 standard. The result shows that sound absorption at low frequency band below 200 Hz increased with the increasing of closed prism number. It is related to the coupling effect between the cavities of the absorber element and the prisms that changes reactance of the coupled structure. In the other side, a half wave resonance like effect occur on the use of opened prisms inclusion, which is increase the sound absorption performance at mid to high frequency range between 800 Hz to 1,25 kHz.  </p>

Comparison of multiple-layer versus multiple-cavity microperforated panels for sound absorption at low frequency

2021 ◽  
Vol 69 (4) ◽  
pp. 341-350
Author(s):  
Pedro Cobo ◽  
Francisco Simón ◽  
Carlos Colina
Keyword(s):  
Sound Absorption ◽  
Low Frequency ◽  
Single Layer ◽  
Helmholtz Resonator ◽  
Layer Versus ◽  
Low Frequencies ◽  
High Frequencies ◽  
Multiple Layer ◽  
Band Absorption ◽  
Microperforated Panels

Microperforated panels (MPPs) are recognized as suitable absorbers for noise control applications demanding special clean and health requirements.While it is relatively easy to design single-layer MPPs for sound absorption in one-to-two octave bands at medium-high frequencies, the performance for low frequencies (below 600 Hz) leads to a rather narrow-band absorption, similar to that of a Helmholtz resonator. However, multiple-layer MPPs can be designed as sound absorbers that yield low-frequency absorption in a wide frequency band. Recently, multiple-cavity perforated panels have been proposed to improve the performance of MPPs in the low-frequency range. In this article, the capability of multiple-layer and multiple-cavity MPPs to provide sound absorption at low frequencies is analyzed.

scholarly journals Effect of Porous Materials Combination in Layers on Sound Absorption Characteristics

2015 ◽  
Vol 773-774 ◽  
pp. 210-215
Author(s):  
Muhd Hafeez Zainulabidin ◽  
M.H.M. Yusuff ◽  
Al Emran Ismail ◽  
M.Z. Kasron ◽  
A.S.M. Kassim
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Low Frequency ◽  
Sound Absorption Coefficient ◽  
Frequency Range ◽  
Sound Absorber ◽  
Number Of Layers ◽  
Combination Number ◽  
Impedance Tubes ◽  
Absorption Characteristics

This paper describes the investigation and analysis on two materials in which one material is a relatively good sound absorber at low frequency range and another is a relatively good sound absorber at high frequency range, combined together in layers to form a better sound absorber for a wider range of frequencies. The layer combinations of the materials are varied and the values of Sound Absorption Coefficient, α are measured experimentally by using impedance tubes with two microphones transfer function method according to ISO 10534-2 standard. The results obtained are compared in terms of the order of material and the number of layer combinations of materials for each sample. The orders of combinations and number of layers of combinations have significant influence on the sound absorption characteristics. The order of materials has reversed effect on Sound Absorption Coefficient, α as the number of layer combination is increased. Increase in the combination number will make the specimen performed relatively better at a wider frequency range.

scholarly journals An innovative composite plywood for the acoustic improvement of small closed spaces

Holzforschung ◽  
2017 ◽  
Vol 71 (6) ◽  
pp. 521-526
Author(s):  
Francesco Negro ◽  
Corrado Cremonini ◽  
Marco Fringuellino ◽  
Roberto Zanuttini
Keyword(s):  
Sound Absorption ◽  
Resonance Effect ◽  
Low Frequency ◽  
Frequency Range ◽  
Honeycomb Core ◽  
Final Size ◽  
Absorption Properties ◽  
Reverberation Chamber ◽  
The Core ◽  
Dining Room

Abstract Poor acoustics is a common problem in many small closed rooms such as offices or dining rooms. Sound absorbing panels used as wall or ceiling coverings can be a remedy. In the present paper, the sound absorption properties of a composite made of two plywood skins bonded to an inner honeycomb core of plywood cells, designed by the authors in a previous study, were improved by drilling the surfaces. The holes communicate with the void cells of the core, activating the Helmholtz resonance effect. The acoustic behavior of small specimens and final-size samples are described, which were also tested in a reverberation chamber and in a real dining room. The developed lightweight composite plywood achieved αmax 0.90 values (maximal sound absorption coefficients) around 400 Hz, i.e. in the low frequency range, resulting in being well suited for various acoustic improvements.

Sign in / Sign up

Export Citation Format

Share Document