Irradiation of Polyamide Measured by Micro-Indentation Test

2015 ◽  
Vol 1120-1121 ◽  
pp. 1179-1182
Author(s):  
Martin Ovsik ◽  
David Manas ◽  
Miroslav Manas ◽  
Michal Stanek ◽  
Adam Skrobak ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Layer ◽  
Material Properties ◽  
Indentation Test ◽  
Polymer Chains ◽  
Cross Linking ◽  
Indentation Hardness ◽  
Chemical Bonds ◽  
Depth Sensing ◽  
Micro Indentation

Cross-linking is a process in which polymer chains are associated through chemical bonds. This research paper deals with the possible utilization of irradiated polyamide. Influence of the intensity of irradiation on micro-indentation hardness was investigated. Material properties created by β – radiation are measured by micro-indentation test using the DSI method (Depth Sensing Indentation). Hardness increased with increasing dose of irradiation at everything samples; however results of micro-indentation test shows increasing in micro-mechanical properties of surface layer. The highest values of micro-mechanical properties were reached radiation dose of 99 kGy, when the micro-mechanical values increased by about 18%.

The Effect of Cross-Linking on Nano-Mechanical Properties of Polyamide

2016 ◽  
Vol 699 ◽  
pp. 37-42 ◽  
Author(s):  
Martin Ovsik ◽  
David Manas ◽  
Miroslav Manas ◽  
Michal Stanek ◽  
Martin Reznicek
Keyword(s):  
Mechanical Properties ◽  
Surface Layer ◽  
Material Properties ◽  
Basic Material ◽  
Nanoindentation Test ◽  
Cross Linking ◽  
Indentation Hardness ◽  
Depth Sensing ◽  
Nanomechanical Properties ◽  
Radiation Crosslinking

Radiation crosslinking of polyamidu 6 (PA 6) is a well-recognized modification of improving basic material characteristics. Radiation, which penetrated through specimens and reacted with the cross-linking agent, gradually formed cross-linking (3D net), first in the surface layer and then in the total volume, which resulted in considerable changes in specimen behaviour. This research paper deals with the possible utilization of irradiated PA6. The material already contained a special cross-linking agent TAIC (5 volume %), which should enable subsequent cross-linking by ionizing β – radiation (15, 30 and 45 kGy). The effect of the irradiation on mechanical behavior of the tested PA 6 was investigated. Material properties created by β – radiation are measured by nanoindentation test using the DSI method (Depth Sensing Indentation). Hardness increased with increasing dose of irradiation at everything samples; however results of nanoindentation test shows increasing in nanomechanical properties of surface layer. The highest values of nanomechanical properties were reached radiation dose of 45 kGy, when the nanomechanical values increased by about 95%. These results indicate advantage cross-linking of the improved mechanical properties.

The Behaviour of Cross-Linking Filled PP to Micro-Indentation Test

2016 ◽  
Vol 368 ◽  
pp. 138-141
Author(s):  
Martin Ovsík ◽  
Vojtech Šenkeřík ◽  
David Manas ◽  
Miroslav Maňas ◽  
Michal Stanek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Indentation Test ◽  
Polymer Chains ◽  
Beta Radiation ◽  
Cross Linking ◽  
X Ray Diffraction ◽  
Depth Sensing ◽  
Surface Layers ◽  
Micro Indentation ◽  
Different Doses

Cross-linking is a process in which polymer chains are associated through chemical bonds. Radiation, which penetrated through specimens and reacted with the cross-linking agent, gradually formed cross-linking (3D net), first in the surface layer and then in the total volume, which resulted in considerable changes in specimen behaviour. The aim of the experiments was to study the influence of different doses of Beta radiation to the structure and micro-mechanical properties of polypropylene filled by 30% glass fiber (PP+GF). Hard surface layers of PP+GF can be formed by radiation cross-linking by β – radiation with doses of 33, 66 and 99 kGy. Material properties created by β – radiation are measured by micro-indentation test using the DSI method (Depth Sensing Indentation). Individual radiation doses caused structural and micro-mechanical changes which have a significant effect on the final properties of the PP+GF tested. Micro-mechanical properties increased with increasing value of the dose of irradiation material (increase about 49%). The changes were examined and confirmed by X-ray diffraction.

Surface Properties of Crosslinking Polyamide Measured by Micro-Indentation Test

2018 ◽  
Vol 919 ◽  
pp. 111-119
Author(s):  
Martin Ovsik ◽  
Michal Stanek ◽  
Vojtech Senkerik
Keyword(s):  
Mechanical Properties ◽  
Surface Layer ◽  
Surface Properties ◽  
Electron Beam Irradiation ◽  
Indentation Test ◽  
Polymer Chains ◽  
Beta Radiation ◽  
Cross Linking ◽  
Micro Indentation ◽  
Different Doses

Cross-linking is a process in which polymer chains are associated through chemical bonds. Radiation, which penetrated through specimens and reacted with the cross-linking agent, gradually formed cross-linking (3D net), first in the surface layer and then in the total volume, which resulted in considerable changes in specimen behavior. This paper studies the effect of different doses of ionizing beta radiation on the micro-mechanical properties of commercially available polyamide. The measured results indicate, that electron beam irradiation is very effective tool for improvement of surface properties of PA6. In terms of micro-mechanical properties, the values of micro-hardness of surface layer increased by 24% at radiation dose of 132 kGy, stiffness of surface micro layer by 26% (132 kGy) as a result of different loads (0.5N and 2N). Improvement of micro-mechanical properties of radiated polyamide has a great significance also for industry. The modified polyamide shifts to the group of materials that have considerably better properties. Its micro-mechanical properties make polyamide ideal for a wide application in areas where higher resistance to wear, creep are required. Commonly manufactured PA6 can hardly fulfil these criteria.

Surface Layer Micro-Hardness of Modified LDPE by Radiation Cross-Linking after Temperature Load

2015 ◽  
Vol 662 ◽  
pp. 177-180 ◽  
Author(s):  
Ales Mizera ◽  
Miroslav Manas ◽  
David Manas ◽  
Martin Ovsik ◽  
Martina Kaszonyiová ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Layer ◽  
Cross Linking ◽  
Indentation Hardness ◽  
Micro Hardness ◽  
Depth Sensing ◽  
Indentation Method ◽  
Temperature Load ◽  
Irradiation Process ◽  
Different Doses

The presented article deals with the research of surface layer ́s micro-mechanical properties of modified LDPE by radiation cross-linking after temperature load. These micro-mechanical properties were measured by the DSI (Depth Sensing Indentation) method on samples which were non-irradiated and irradiated by different doses of the β – radiation and then were temperature loaded. The purpose of the article is to consider to what extent the irradiation process influences the resulting micro-mechanical properties measured by the DSI method. The LDPE tested showed significant changes of indentation hardness and modulus after temperature load.

The Behaviour of Cross-Linking Filled PA66 by Micro-Indentation Test

2016 ◽  
Vol 699 ◽  
pp. 43-48
Author(s):  
Martin Ovsik ◽  
David Manas ◽  
Miroslav Manas ◽  
Michal Stanek ◽  
Vojtech Senkerik
Keyword(s):  
Mechanical Properties ◽  
Surface Layer ◽  
Glass Fiber ◽  
Indentation Test ◽  
Polymer Materials ◽  
Beta Radiation ◽  
Indentation Hardness ◽  
Indentation Modulus ◽  
Polyamide 66 ◽  
Depth Sensing

The process of radiation crosslinking helps to improve some mechanical properties of polymer materials. Micro-mechanical changes in the surface layer of glass-fiber filled PA 66 modified by beta radiation were measured by the Depth Sensing Indentation - DSI method on samples which were non-irradiated and irradiated by different doses of the β - radiation. The specimens were prepared by injection technology and subjected to radiation doses of 0, 33, 66 nad 99 kGy. The change of micro-mechanical properties is greatly manifested mainly in the surface layer of the modified polypropylene where a significant growth of micro-hardness values can be observed. Indentation modulus increased from 1.8 to 3.0 GPa (increasing about 66%) and indentation hardness increased from 87 to 157 MPa (increasing about 80%). This research paper studies the influence of the dose of irradiation on the micro-mechanical properties of semi-crystalline polyamide 66 filled by 30% glass fiber at room temperature. The study is carried out due to the ever-growing employment of this type of polymer.

Micro-Indentation Test of Cross-Linking Polyethylene

2015 ◽  
Vol 1120-1121 ◽  
pp. 1175-1178
Author(s):  
Martin Ovsik ◽  
David Manas ◽  
Miroslav Manas ◽  
Michal Stanek ◽  
Martin Reznicek
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Indentation Test ◽  
Basic Material ◽  
Cross Linking ◽  
Indentation Hardness ◽  
Indentation Modulus ◽  
Linear Polyethylene ◽  
Radiation Crosslinking ◽  
Micro Indentation

Radiation crosslinking of linear polyethylene (LLDPE) is a well-recognized modification of improving basic material characteristics. This research paper deals with the utilization of electron beam irradiated LLDPE on the micro-indentation test. The effect of the irradiation on mechanical behavior of the tested polyethylene was investigated. The results indicate that the mechanical behavior, highly depends on the intensity of irradiation. Toughness and hardness grew with increasing dose of the irradiation LLDPE. Indentation modulus increased from 0.25 to 0.28 GPa and indentation hardness increased from 21.89 to 26.25 MPa. These results indicate advantage crosslinking of the improved mechanical properties.

Micro-Indentation Test and Morphology of Electron Beam Irradiated HDPE

2015 ◽  
Vol 662 ◽  
pp. 189-192
Author(s):  
Martin Ovsik ◽  
Petr Kratky ◽  
David Manas ◽  
Miroslav Manas ◽  
Michal Stanek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Indentation Test ◽  
Polymer Chains ◽  
Cross Linking ◽  
Thermal Treatments ◽  
X Ray Diffraction ◽  
Irradiation Dosage ◽  
The Cross ◽  
Micro Indentation ◽  
Different Doses

Cross-linking is a process in which polymer chains are associated through chemical bonds. The cross-linking level can be adjusted by the irradiation dosage and often by means of a cross-linking booster. The polymer additional cross-linking influences the surface nanoand micro layers in the way comparable to metals during the thermal and chemical-thermal treatments. The aim of this paper is to study the effect of ionizing radiation with different doses (33, 66 and 99 kGy), on micro-mechanical properties of polyethylene (HDPE) and compare these results with those of non-irradiated samples. Influence of the cross-linking by β – radiation of the tested HDPE on micro-indentation test and morphology was investigated. Micro-mechanical properties increased with increasing value of the dose of irradiation material. The changes were examined and confirmed by X-ray diffraction.

scholarly journals LOCAL NANO-MECHANICAL PROPERTIES OF CROSS-LINKED POLYBUTYLENE

2020 ◽  
Vol 27 ◽  
pp. 112-115
Author(s):  
Martin Ovsík ◽  
Michal Staněk ◽  
Adam Dočkal ◽  
Petr Fluxa
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Polymer Chains ◽  
Cross Linking ◽  
Indentation Hardness ◽  
Indentation Modulus ◽  
Depth Sensing ◽  
Polybutylene Terephthalate ◽  
3D Network ◽  
Irradiation Dosage

Cross-linking is a process in which polymer chains are associated through chemical bonds. The cross-linking level can be adjusted by the irradiation dosage and often by means of a cross-linking booster. The polymer additional cross-linking influences the surface nano and micro layers in the way comparable to metals during the thermal and chemical-thermal treatments. Polybutylene terephthalate (PBT) can be found in a group of structural polymers, which are often used in industry, especially in automotive. Applying the technology of electron radiation induces a creation of 3D network structure, which improves the local mechanical properties. These were later measured by a depth sensing indentation (DSI) test. This state of the art method is based on immediate detection of indentation depth in relation to applied force. The creation of 3D network caused an increase in nano-mechanical properties values, such as indentation hardness and indentation modulus, in comparison to the virgin material. The indentation hardness rose by 80%, while the indentation modulus elevated by 62%. The selected structural materials, e.g. PBT, were modified by the electron irradiation in a positive way and as such could be moved to a group of high performance materials.

Improvement of PA6 Mechanical Properties by Radiation Cross-Linking

2015 ◽  
Vol 1120-1121 ◽  
pp. 1163-1166 ◽  
Author(s):  
Petr Kratky ◽  
David Manas ◽  
Miroslav Manas ◽  
Michal Stanek ◽  
Martin Ovsik ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Layer ◽  
Polymer Material ◽  
Polyamide 6 ◽  
Polymer Materials ◽  
Cross Linking ◽  
Depth Sensing ◽  
Surface Layers ◽  
Hard Surface ◽  
End Use

Influence of mechanical properties of the hard surface layer of modified polyamide 6 is studied. Mechanical properties are acquired by nanohardness test with using the DSI method (Depth Sensing Indentation). Hard surface layers are created by radiation cross-linking technology. This technology allows polymer materials modification followed by the change of their end-use properties. The surface layer of polymer material is modified by ionizing β - radiation. When the polymer material is exposed to the β radiation, it is possible to observe changes of the surface layer at applied load. Radiation cross-linking usually improves strength, reduces creep, contributes to chemical resistance improvement, and in many cases improves tribological properties.

Micro-Hardness of PA6 Influenced by Beta Irradiation

2015 ◽  
Vol 752-753 ◽  
pp. 322-325
Author(s):  
Martin Ovsik ◽  
David Manas ◽  
Miroslav Manas ◽  
Michal Stanek ◽  
Martin Reznicek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Crosslinking Agent ◽  
Polyamide 6 ◽  
Point Of View ◽  
Polymer Chains ◽  
Indentation Creep ◽  
Indentation Hardness ◽  
Indentation Modulus ◽  
Micro Hardness ◽  
Depth Sensing

In this paper, the effect of the electron beam irradiation on the indentation hardness, indentation modulus and indentation creep have been studied by means of the Depth sensing indentation (DSI). Cross-linking is a process in which polymer chains are associated through chemical bonds. Radiation doses of 33, 66 and 99 kGy were used for unfilled polyamide 6 with the 7% crosslinking agent (triallyl isocyanurate). Beta irradiation of the examined thermoplastic caused the growth of values of material parameters as micro-hardness, indentation modulus or indentation creep etc. From this point of view, there may be new application in areas with mechanical properties higher than their original properties. This study compared the mechanical properties of irradiated and non-irradiated PA6.

Sign in / Sign up

Export Citation Format

Share Document