Method of Slab Size Design Based on Maximum Yield Rate of Plates

2011 ◽  
Vol 204-210 ◽  
pp. 942-945
Author(s):  
Cheng Zhong Song ◽  
Li Min Shen ◽  
Qing Da Zhang ◽  
Fang He ◽  
Yi Min Jiang ◽  
...  
Keyword(s):  
Economic Efficiency ◽  
Maximum Yield ◽  
Steel Plates ◽  
Compression Rate ◽  
Spread Rate ◽  
Yield Rate

To improve the yield rate of steel plates, a method of slab size design is proposed based on maximum yield rate of plates. It includes material transformations algorithm and optimization of slab selection. Many factors are considered in the model covering the equipment capacity, spread rate, compression rate, burning loss and cutting loss. Initially, all possible types of slabs are obtained through material transformations algorithm after the order input. This allows the eventual determination of the slabs of the largest yield rate through the optimization of slab selection. The experiments prove that the model can reduce a number of materials and lessen the pressure of the inventory. An effective increase of plate yield can be expected to improve the economic efficiency of enterprise.

Rapidly extracted (0.02 M CaCl2-soluble) reactive aluminum as a measure of aluminum toxicity in soils

Soil Research ◽  
1989 ◽  
Vol 27 (4) ◽  
pp. 663 ◽  
Author(s):  
EA Close ◽  
HKJ Powell
Keyword(s):  
Salicylic Acid ◽  
White Clover ◽  
Aluminum Toxicity ◽  
Maximum Yield ◽  
Acid Soils ◽  
Aluminium Toxicity ◽  
Field Method ◽  
Colorimetric Analysis ◽  
Aluminium Species

This paper examines the use of short extraction times, and the determination of aluminium with chrome azurol S (CAS), for the estimation of 0.02 M CaCl2-soluble aluminium in soils. It reports the correlation between CAS-reactive aluminium in 5 min extracts and percent maximum yield of white clover (Trifolium repens) for a series of acid soils. The reactivity of soluble and colloidal aluminium species with the metallochromic reagent CAS has been assessed. ~ l ( a q ) ~ + , simple hydroxy species and complexes of weakly binding ligands (salicylic acid, tannins) are CAS-reactive (2 rnin). In contrast, complexes of strongly binding ligands (citric acid, fulvic acid) are not CAS-reactive ([Al] ~ [L] ~ [CAS] ~ 1-2~10-5 M). For a series of six limed phosphated topsoils and subsoils (pH 4.2-5.5), 0.02 M CaCl2- soluble aluminium, as determined with CAS, was negatively correlated against the percent maximum yield of white clover; r2 = -0.73** (5 min extraction), n = 20. This correlation is similar to that for yield against total aluminium as determined by atomic absorption spectroscopy after 60 min extraction (r2 = -0.77**). However, the colorimetric analysis is more convenient and sensitive; further, it does not measure colloidal and polymeric aluminium species (which may not be plant-available). The satisfactory correlation achieved for short extraction times suggests use of CAS for a rapid field method for aluminium toxicity in soils.

DETERMINATION OF THE REMOTION PERCENTAGE OF BARNACLE BIOFOULING FROM MARINE STEEL PLATES USING STEEL BRUSH FOR CLEANING

2021 ◽  
Author(s):  
Rodrigo Guedes ◽  
Vinícius Teles ◽  
Paulo Henrique Vieira Magalhães ◽  
Ana Letícia Pilz de Castro ◽  
Danilo Lisboa ◽  
...  
Keyword(s):  
Steel Plates ◽  
Steel Brush

A PROSPECTS OF THE SUPER-INTENSIVE UNSUPPORTED GARDENS ESTABLISHMENT OF COLUMNAR APPLE TREE VARIETIES

1970 ◽  
pp. 45-48
Author(s):  
S. А. Korneeva ◽  
Е. N. Sedov ◽  
T. V. Янчук
Keyword(s):  
Economic Efficiency ◽  
Apple Tree ◽  
Maximum Yield ◽  
Biological Features ◽  
Apple Cultivars ◽  
High Level ◽  
Dwarf Rootstocks

Columnar apple cultivars are optimally suited to lay apple tree plantings using intensive technology, which provides for super-dense placement of trees. The article considers a variant of growing columnar apple cultivars on inserts of dwarf rootstocks 3-17-38 and 62-396. The use of dwarf rootstocks 3-17-38 and 62-396 as intercalar inserts in the cultivation of columnar apple cultivars, along with good anchoring of plants, provides high precocity, productivity and economic efficiency of planting. All the costs of laying the orchard and annual works on agrotechnical care of the trees were paid off in the fourth year after planting.The economic and biological features of the columnar cultivars provided not only a quick return of the investments, but also a high level of profitability. The profitability of the studied columnar planting for the 6th year after planting (2020) on average for all cultivars was 106.0 % on the insert of the dwarf rootstock 62-396 and 104.7 % on the insert 3-17-38. The profit received on average for the plantings amounted to 2 378 661 rubles per ha. In the group of the studied cultivars, there is a difference in economic efficiency. The lowest level of productivity and profitability was in the Vostorg cultivar: on average, on two inserts, the yield in 2020 was 27.3 t/ha and the profitability was 66.6%. The Girlyanda cultivar was characterized by the maximum yield and profitability: 88.0 t/ha and 115.8%, respectively.

In Situ Measurement of Poisson’s Ratio of Steel Plates During Thermal Processes Using Resonant Modes

2021 ◽  
Author(s):  
Clemens Grünsteidl ◽  
Christian Kerschbaummayr ◽  
Edgar Scherleitner ◽  
Bernhard Reitinger ◽  
Georg Watzl ◽  
...  
Keyword(s):  
Poisson’S Ratio ◽  
Dual Phase Steel ◽  
Steel Plates ◽  
Poisson's Ratio ◽  
Austenitic Phase ◽  
Resonant Modes ◽  
Longitudinal Sound Velocity ◽  
Contact Free

Abstract We demonstrate the determination of the Poisson’s ratio of steel plates during thermal processing based on contact free laser ultrasound measurements. Our method utilizes resonant elastic waves sustained by the plate, provides high amplitudes, and requires only a moderate detection bandwidth. For the analysis, the thickness of the samples does not need to be known. The trend of the measured Poisson’s ratio reveals a phase transformation in dual-phase steel samples. While previous approaches based on the measurement of the longitudinal sound velocity cannot distinguish between the ferritic and austenitic phase above 770°C, the shown method can. If the thickness of the samples is known, the method also provides both sound velocities of the material. The gained complementary information could be used to analyze phase composition of steel from low temperatures up to its melting point.

Evaluation of Residual Stresses in PVD Coatings by Means of Strip Substrate Length Variation and Curvature Method of Plate Substrate

2017 ◽  
Vol 267 ◽  
pp. 212-218 ◽  
Author(s):  
Harri Lille ◽  
Alexander Ryabchikov ◽  
Jakub Kõo ◽  
Eron Adoberg ◽  
Liina Lind ◽  
...  
Keyword(s):  
Residual Stresses ◽  
Length Change ◽  
Steel Plates ◽  
Length Variation ◽  
Pvd Coatings ◽  
Compressive Stresses ◽  
Steel Strips ◽  
Middle Cross Section ◽  
Method Strip

The aim of the study was to determine macroscopic residual stresses in Physical Vapor Deposits (PVD) coatings through measurement of the length variation of the strip substrates coated on both sides. The length change of the strip was reduced to the deflection of the middle cross-section of the elastic element and was recorded by four strain gauges. For validating the obtained results, the conventional curvature method was used. As an application, residual stresses in hard AlCrN PVD coatings were investigated. The coatings were nanolayered to achieve better coating toughness for blanking and punching applications. The steel strips and steel plates with two thicknesses were used as the substrate. The values of the compressive residual stresses, determined by both methods for the investigated coatings, were very high (3.3 -3.6 GPa) independent of coating thickness and practically equal within the measurement uncertainty of the method. Good agreement between the experimental results obtained with both methods suggests that the presented method, strip length variation, is applicable for determination of residual stresses in coatings. Compressive stresses in coatings are desirable as they strengthen the coating.

Determination of some Mechanical Characteristics by Vibration Testing of Welded Structures with Tubular Wire

2013 ◽  
Vol 814 ◽  
pp. 127-134 ◽  
Author(s):  
Liviu Bereteu ◽  
Raul Moisa ◽  
Mihaela Popescu ◽  
Gheorghe Drăgănescu ◽  
Radu Alexandru Rosu ◽  
...  
Keyword(s):  
Steel Wire ◽  
Welding Process ◽  
Tensile Tests ◽  
Operating Conditions ◽  
Steel Plates ◽  
Vibration Testing ◽  
Welded Structures ◽  
Appropriate Behavior ◽  
Welded Structure

Applicability of the welded structures in different operating conditions requires experimental research developed in conditions previously imposed for each punctual application. There are analyzed in this case, in terms of vibration testing, some welded joints made with usual tubular steel wire. This is the case of the type carbon steel plates S235 JR according to EN 10025, with a thickness of 3 mm welded with MIG/MAG welding process with R713 tubular wire with a diameter of 1.2 mm, using SelcoNeoMig 3500 equipment. By processing the received signal based on the vibrations response to determine the elastic modulus of the welded structure, which will then be compared both with the modulus value obtained by tensile tests, and with the theoretical value obtained. The results thus obtained will be the basis of design, in optimal conditions of the welded structures regarding the appropriate behavior to the demands imposed.

scholarly journals Determination of Chemical Composition and Antimicrobial Activity of Melaleuca cajuputi Essential Oil from Quang Tri Province, Vietnam

2020 ◽  
Vol 32 (9) ◽  
pp. 2203-2207
Author(s):  
TRAN QUOC TOAN ◽  
LAI PHUONG PHUONG THAO ◽  
NGUYEN QUYET CHIEN ◽  
NGUYEN THI HONG VAN ◽  
ÐOAN LAN PHUONG ◽  
...  
Keyword(s):  
Essential Oil ◽  
Maximum Yield ◽  
Batch Process ◽  
Gram Negative Bacteria ◽  
Gram Negative ◽  
Qualitative And Quantitative ◽  
Melaleuca Cajuputi ◽  
Main Components ◽  
Bactericidal Agent

The essential oil of Melaleuca cajuputi was obtained by hydrodistillation method. This work aims to adopt water as a solvent in a batch process to extract essential oil from Melaleuca cajuputi fresh leaves. The leaves are collected from Quang Tri Province, Vietnam. Analysis of constituents was performed by GC/MS. The maximum yield ranged from 0.6 to 0.7%. Several compounds have been identified in high quantities and meaningful qualitative and quantitative differences have been observed under different conditions. The main components of the M. cajuputi essential oil included eucalyptol (27.512%), γ-terpinene (8.59%), terpinolene (9.047%), β-eudesmene (3.359%), α- selinene (3.889%), α-terpineol (4.108%), 1R-α-pinene (2.158%), caryophyllene (6.48%) and α-caryophyllene (3.522%). This study has confirmed that the essential oil of M. cajuputi essential oil is a promising bactericidal agent on several Gram-positive and Gram-negative bacteria.

Sign in / Sign up

Export Citation Format

Share Document