Study in Simulated Heat-Affected Zone of Ship Steel

2011 ◽  
Vol 228-229 ◽  
pp. 1196-1200
Author(s):  
Wen Yan Liu ◽  
Ji Bin Liu ◽  
Cong Mao Zhu ◽  
Hui Wang
Keyword(s):  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Physical Simulation ◽  
Wide Range ◽  
Lath Bainite ◽  
Quench Hardening ◽  
Impact Energies ◽  
The Impact ◽  
Cct Diagrams

The experiments were carried out upon the determination of simulated heat-affected zone continuous cooling transformation (SH-CCT) diagrams, the characteristics of microstructure and Vickers hardness of SH-CCT specimens, and impact toughness in simulated coarse grain heat-affected zone (CGHAZ) of ship steels under different heat input based on physical simulation. The SH-CCT diagram reveals that bainite is always obtained in a wide range of cooling rates. When the maximum cooling rate reaches 100 °C/s (t8/5=3 seconds), the maximum fraction of martensite (8%) is obtained and the microstructures mainly consist of lath bainite and the hardness is only 255 HV. This demonstrates that the steel has a low quench-hardening tendency and excellent resistance to cold cracking. There are no obvious hardening and softening phenomena in simulated CGHAZ. Test results of impact toughness under different heat input in simulated CGHAZ show that the impact energies reach over 30 J at -40 °C when t8/5 is less than 20 s, meeting the stipulated requirements of ship steel (≥22 J at -40 °C) but no great allowance. Thus, to meet the requirement of properties during welding, it is proposed to choose t8/5 ranging from 5 to 20 s, correspondently the line energies ranging from 14 to 37 KJ/cm for 30 mm thick plate.

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

2018 ◽  
Vol 937 ◽  
pp. 61-67
Author(s):  
Yu Jie Li ◽  
Jin Wei Lei ◽  
Xuan Wei Lei ◽  
Oleksandr Hress ◽  
Kai Ming Wu
Keyword(s):  
Low Temperature ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
High Strength ◽  
High Heat ◽  
Coarse Grained ◽  
Low Temperature Impact Toughness ◽  
The Impact ◽  
Welding Processes

Utilizing submerged arc welding under heat input 50 kJ/cm on 60 mm thick marine engineering structure plate F550, the effect of preheating and post welding heat treatment on the microstructure and impact toughness of coarse-grained heat-affected zone (CGHAZ) has been investigated. The original microstructure of the steel plate is tempered martensite. The yield and tensile strength is 610 and 660 MPa, respectively. The impact absorbed energy at low temperature (-60 °C) at transverse direction reaches about 230~270 J. Welding results show that the preheating at 100 °C did not have obvious influence on the microstructure and toughness; whereas the tempering at 600 °C for 2.5 h after welding could significantly reduce the amount of M-A components in the coarse-grained heat-affected zone and thus improved the low temperature impact toughness.

Physical Simulation for Evaluating Heat-Affected Zone Toughness of High and Ultra-High Strength Steels

2013 ◽  
Vol 762 ◽  
pp. 711-716 ◽  
Author(s):  
Risto O. Laitinen ◽  
David A. Porter ◽  
L. Pentti Karjalainen ◽  
Pasi Leiviskä ◽  
Jukka Kömi
Keyword(s):  
Heat Affected Zone ◽  
Heat Input ◽  
Physical Simulation ◽  
Energy Requirement ◽  
High Strength Steels ◽  
High Strength ◽  
Coarse Grained ◽  
Test Results ◽  
Ultra High Strength Steels ◽  
The Impact

Physical simulation of the most critical sub-zones of the heat-affected zone is a useful tool for the evaluation of the toughness of welded joints in high-strength and ultra-high-strength steels. In two high-strength offshore steels with the yield strength of 500 MPa, the coarse grained, intercritical and intercritically reheated coarse grained zones were simulated using the cooling times from 800 to 500 °C (t8/5) 5 s and 30 s. Impact and CTOD tests as well as microstructural investigations were carried out in order to evaluate the weldability of the steels without the need for expensive welding tests. The test results showed that the intercritically reheated coarse grained zone with the longer cooling time t8/5=30 s was the most critical sub-zone in the HAZ due to the M-A constituents and coarse ferritic-bainitic microstructure. In 6 mm thick ultra-high-strength steel Optim 960 QC, the coarse grained and intercritically reheated coarse grained zones were simulated using the cooling times t8/5 of 5, 10, 15 and 20s and the intercritical zone using the cooling times t8/5 of 5 and 10 s in order to select the suitable heat input for welding. The impact test results from the simulated zones fulfilled the impact energy requirement of 14 J (5x10 mm specimen) at -40 °C for the cooling times, t8/5, from 5 to 15 s, which correspond to the heat input range 0.4-0.7 kJ/mm (for a 6 mm thickness).

Effect of Heat Input on Toughness of Coarse-Grained Heat-Affected Zone of an Ultra Low Carbon Acicular Ferrite Steel

2012 ◽  
Vol 538-541 ◽  
pp. 2003-2008 ◽  
Author(s):  
Zheng Hai Xia ◽  
Xiang Liang Wan ◽  
Xue Li Tao ◽  
Kai Ming Wu
Keyword(s):  
Electron Microscopy ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Acicular Ferrite ◽  
High Heat ◽  
Coarse Grained ◽  
Low Carbon ◽  
Ferrite Steel ◽  
The Impact

The effect of heat input on toughness of coarse-grained heat-affected zone of an ultra low carbon acicular ferrite steel were investigated when the welding was conducted with high heat input. Microstructural observations, energy dispersive X-ray spectroscopy analyses were conducted using optical microscopy, scanning electron microscopy and transmission electron microscopy, respectively. The microstructures of coarse-grained heat-affected zone consist of predominantly bainitic microstructure and a small proportion of acicular ferrite grains. The bainitic microstructures become coarsened with increasing heat input. The impact toughness of coarse-grained heat-affected zone remained at a higher level when the heat input ranged from 42 to 55 kJ/cm. It became not stable and dropped to a lower level when the heat input increased to 110150 kJ/cm. The enhancement in impact toughness was attributable to the MnS precipitation on the pre-formed Ti oxides as well as the formation of intragranular ferrite. When specimens were welded with higher heat input, the deterioration of impact toughness was caused by the coarsening of austenite grains.

Influence of Weld Heat Input on Weld Joint between B610CF and 16MnR Steel

2010 ◽  
Vol 154-155 ◽  
pp. 421-424
Author(s):  
Tian Hui Zhang ◽  
Hong Cai Fu ◽  
Wen Min Liu ◽  
Yun Chun Cheng ◽  
Ren Ping Xu
Keyword(s):  
Impact Toughness ◽  
Weld Joint ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Experimental Results ◽  
Distinct Difference ◽  
Shielded Metal Arc Welding ◽  
Metal Arc Welding ◽  
The Impact ◽  
Weld Heat

The influence of weld heat input on weld joint between B610CF and 16MnR steel using shielded metal arc welding method was investigated by metallographic experiment and mechanical properties experiment. Metallographic experimental results show that in welded metal with the increasing of weld heat input the quantity of bainite is decreased and crystalline grain is larger; but in both B610CF and 16MnR steel heat affected zone, with the increasing of weld heat input there is no distinct difference in microstructure. Mechanical property experimental results show that in weld metal with the increasing of weld heat input the impact toughness decreases, but in both B610CF and 16MnR heat affected zone, there is less difference in impact toughness; and there is no distinct difference in tensile strength and plasticity of weld joint, which is consistent with the metallographic experiment results.

Investigations on Impact Toughness and Microstructure Characteristics of Gas Metal Arc Welded HY-80 Steel Plate

2019 ◽  
Vol 964 ◽  
pp. 68-79 ◽  
Author(s):  
Herry Oktadinata ◽  
Winarto Winarto ◽  
Eddy S. Siradj
Keyword(s):  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Arc Welding ◽  
Steel Plate ◽  
Gas Metal Arc Welding ◽  
Hardness Test ◽  
Fusion Line ◽  
High Yield ◽  
The Impact

HY-80 is the high yield steel that commonly used for naval ship and submarine. Arc welding operations are critical stage in fabrication of this steel. During welding, the problem may occur in the heat affected zone due to the high temperature makes the microstructure suddenly changes. Coarse grain heat affected zone (CGHAZ) develops close to the fusion line, steel become brittle and the impact toughness decrease. This research investigated the microstructure of HY-80 weldment, impact toughness at sub-zero temperatures, and hardness distribution along cross-section of the welded joint. ER100S welding wire, Ar+10%CO2 shielding gas mixture and single V-groove butt joint with an angle of 60° were selected prior to welding. 12 mm thick of HY-80 steel plate that used in this experiment was multipass welded by gas metal arc welding (GMAW). Impact toughness at sub-zero temperature, hardness and microstructure evolutions of base metal (BM), heat affected zone (HAZ) and weld metal (WM) were observed. The result shows at a temperature of-80 °C, the lowest impact toughness was measured at WM (61 J) as compared to fusion line (101 J) and BM (217 J). The hardness measurement shows the maximum hardness was measured in CGHAZ followed WM and BM. Vickers hardness test result of weld joint at bottom area are higher than top area. It may caused of the low heat input of back weld compared to other passes. The lower heat input, cooling rate increased and initiate the formation of hard phase. The microstructure of WM shows acicular ferrites and non-metallic inclusions, these inclusions may deteriorate the impact toughness.

Microstructures and Toughness in Simulated Coarse Grain Heat-Affected Zones of Copper-Bearing Steel

2008 ◽  
Vol 575-578 ◽  
pp. 910-914
Author(s):  
Wen Yan Liu ◽  
Lai Wang ◽  
Ji Bin Liu ◽  
Ping He Li ◽  
Kai Miao ◽  
...  
Keyword(s):  
Impact Toughness ◽  
Heat Affected Zone ◽  
Physical Simulation ◽  
Bearing Steel ◽  
Granular Bainite ◽  
Coarse Grain ◽  
Factors Influencing ◽  
Visible Effect ◽  
Main Factors ◽  
The Impact

Microstructures and toughness of simulated coarse grain heat-affected zone of hot continuously rolled copper-bearing steel were investigated using physical simulation. The results showed that brittlement is easy to happen in the region of CGHAZ with slower thermal cycles (t8/5≥45s). Granular bainite transformed from austenite led to brittlement. The dimensions of granular martensite and austenite (M-A) constituents are main factors influencing the impact toughness. There is no visible effect on the toughness when the dimensions of M-A constituents are less than 1μ m. However, the toughness decreases greatly once the dimensions exceed 1μ m. Therefore, decreasing the dimensions of M-A constituents by controlling weld heat input will do good to improve the impact toughness of copper-bearing steel.

Effect of Heat Input on Impact Toughness of Coarse-Grained Heat-Affected Zone of a Nb-Ti Microalloyed Pipeline Steel

2012 ◽  
Vol 538-541 ◽  
pp. 2026-2031 ◽  
Author(s):  
Zhou Gao ◽  
Ran Wei ◽  
Kai Ming Wu
Keyword(s):  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Pipeline Steel ◽  
High Heat ◽  
Coarse Grained ◽  
Bainitic Microstructure ◽  
Homogenous Distribution ◽  
High Heat Input ◽  
The Impact

The effect of varying heat inputs (20, 100, 200 kJ/cm) on the microstructures and toughness of the simulated coarse-grained heat-affected zone of a Nb-Ti microalloyed pipeline steel were investigated utilizing optical and electron microscope. Results showed that the impact toughness of the coarse-grained heat-affected zone maintained a higher level at the heat input of 20 and 100 kJ/cm, whereas it dropped to a much lower level at the heat input of 200 kJ/cm. The good toughness was attributed to the grain refinement and the homogenous distribution of fine and elongated martensite/austenite constituents. The deterioration of toughness for high heat input simulated welding was mainly caused by the coarse bainitic microstructure and massive martensite/austenite constituents.

scholarly journals Effect of Welding Heat Input on Microstructure and Impact Toughness in the Simulated CGHAZ of Low Carbon Mo-V-Ti-N-B Steel

Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1997
Author(s):  
Mingliang Qiao ◽  
Huibing Fan ◽  
Genhao Shi ◽  
Leping Wang ◽  
Qiuming Wang ◽  
...  
Keyword(s):  
Impact Toughness ◽  
Heat Input ◽  
Acicular Ferrite ◽  
Granular Bainite ◽  
Equivalent Diameter ◽  
Low Carbon ◽  
Welding Heat Input ◽  
Lath Bainite ◽  
Gleeble 3500 ◽  
The Impact

Welding thermal cycles with heat inputs ranging from 25 to 75 kJ/cm were performed on a Gleeble 3500. The impact energy improved significantly (from 10 to 112 J), whereas the simulated coarse-grain heat-affected zone (CGHAZ) microstructure changed from lath bainite ferrite (LBF) and granular bainite ferrite (GBF) + martensite/austenite (M/A) to acicular ferrite (AF) + polygonal ferrite (PF) + M/A as the heat input increased. Simultaneously, the mean coarse precipitate sizes and the degree of V(C,N) enrichment on the precipitate surface increased, which provided favorable conditions for intragranular ferrite nucleation. The Ar3 of CGHAZ increased from 593 °C to 793 °C with increasing heat inputs; the longer high-temperature residence time inhibited the bainite transformation and promoted the ferrite transformation. As a result, acicular ferrite increased and bainite decreased in the CGHAZ. The CGHAZ microstructure was refined for the acicular ferrite segmentation of the prior austenite, and the microstructure mean equivalent diameter (MED) in the CGHAZ decreased from 7.6 µm to 4.2 µm; the densities of grain boundaries higher than 15° increased from 20.3% to 45.5% and significantly increased the impact toughness. The correlation of heat input, microstructure, and impact toughness was investigated in detail. These results may provide new ideas for the development of high welding heat input multiphase steels.

scholarly journals Continuous Cooling Transformation Diagram, Microstructures, and Properties of the Simulated Coarse-Grain Heat-Affected Zone in a Low-Carbon Bainite E550 Steel

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 939 ◽  
Author(s):  
Yun Zong ◽  
Chun-Ming Liu
Keyword(s):  
Impact Toughness ◽  
Cooling Rate ◽  
Vickers Hardness ◽  
Heat Affected Zone ◽  
Granular Bainite ◽  
Coarse Grain ◽  
Low Carbon ◽  
Transformation Diagram ◽  
Lath Bainite ◽  
Continuous Cooling Transformation Diagram

In order to provide important guidance for controlling and obtaining the optimal microstructures and mechanical properties of a welded joint, the continuous cooling transformation diagram of a new low-carbon Nb-microalloyed bainite E550 steel in a simulated coarse-grain heat-affected zone (CGHAZ) has been constructed by thermal dilatation method in this paper. The welding thermal simulation experiments were conducted on a Gleeble-3800 thermo-mechanical simulator. The corresponding microstructure was observed by a LEICA DM2700M. The Vickers hardness (HV) and the impact toughness at −40 °C were measured according to the ASTM E384 standard and the ASTM E2298 standard, respectively. The experimental results may indicate that the intermediate temperature phase transformation of the whole bainite can occur in a wide range of cooling rates of 2–20 °C/s. In the scope of cooling rates 2–20 °C/s, the microstructure of the heat-affected zone (HAZ) mainly consists of lath bainite and granular bainite. Moreover, the proportion of lath bainite increased and granular bainite decreased as the cooling rate increasing. There is a spot of lath martensite in the microstructure of HAZ when the cooling rate is above 20 °C/s. The Vickers hardness increases gradually with the increasing of the cooling rate, and the maximum hardness is 323 HV10. When the cooling time from 800 °C to 500 °C (t8/5) is 5–15 s, it presents excellent −40 °C impact toughness (273–286 J) of the CGHAZ beyond the base material (163 J).

Physical Simulation of Weldability of Weldox 1300 Steel

2013 ◽  
Vol 762 ◽  
pp. 551-555 ◽  
Author(s):  
Marek Stanislaw Węglowski ◽  
Marian Zeman ◽  
Miroslaw Lomozik
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Physical Simulation ◽  
High Strength ◽  
Parent Material ◽  
Cooling Time ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Transformation Diagrams ◽  
The Impact

In the present study, the investigation of weldability of new ultra-high strength - Weldox 1300 steel has been presented. The thermal simulated samples were used to investigate the effect of welding cooling time t8/5 on the microstructure and mechanical properties of the heat affected zone (HAZ). In the frame of these investigation the microstructure was studied by the light (LM) and transmission electron microscopies (TEM). It has been shown that the microstructure of the Weldox 1300 steel is composed of tempered martensite, and inside the laths the minor precipitations mainly V(CN) and molybdenum carbide Mo2C were observed. Mechanical properties of parent material were analysed by the tensile, impact and hardness tests. In details the influence of cooling time in the range of 2,5 - 300 s. on hardness, impact toughness and microstructure of simulated HAZ was studied by using welding thermal simulation test. The results show that the impact toughness and hardness decrease with the increase of t8/5 under the condition of a single thermal cycle in simulated HAZ. The continuous cooling transformation diagrams (CCT-W for welding conditions) of Weldox 1300 steel for welding purposes was also elaborated. The steel Weldox 1300 for cooling time in the range of 2,5 - 4 s showed martensite microstructure, for time from 4 s to 60 s mixture of martensite and bainite, and for longer cooling time mixture of ferrite, bainite and martensite. The results indicated that the weldability of Weldox 1300 steel is limited and to avoid the cold cracking the preheating procedure or medium net linear heat input should be used.

Sign in / Sign up

Export Citation Format

Share Document