An Investigation on Green Machining: Cutting Process Characteristics of Organic Metalworking Fluid

2011 ◽  
Vol 230-232 ◽  
pp. 809-813 ◽  
Author(s):  
T.S. Lee ◽  
H.B. Choong
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Temperature ◽  
Milling Process ◽  
Cutting Process ◽  
Depth Of Cut ◽  
Process Characteristics ◽  
Metalworking Fluid ◽  
Soy Bean Oil ◽  
Ph Level

This paper compares the cutting process characteristics of organic and inorganic coolant for milling process. RBD(refined, bleached & deodorized) palm olein, refined canola and soy bean oil were selected as based oil for soluble mixture(organic) while Jetkool SC95 as inorganic metalworking fluid (MWF). Throughout the research, carbide coated cutting tool and JIS SS400 mild steel are used with various feed rate, depth of cut and fixed spindle speed to determine the cutting temperature, forces and also surface roughness. Heat capacity, pH and tool wear assessment are carried out as well with same material. From the research, cutting temperature, cutting force and surface roughness are proportional to the feed rate and depth of cut. The MWFs pH level also drops after cutting process. Each MWFs showing their different strength on different assessments, overall from the results obtained, palm oil has a high potential to be marketed as organic MWF.

Monitoring of Surface Roughness Based on Cutting Force and Cutting Temperature in Ball-End Milling Process by Utilizing Response Surface Analysis

2015 ◽  
Vol 799-800 ◽  
pp. 324-328
Author(s):  
Panrawee Yaisuk ◽  
Somkiat Tangjitsitcharoen
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Response Surface ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Temperature ◽  
Milling Process ◽  
Depth Of Cut ◽  
Tool Diameter ◽  
End Milling Process

The surface roughness is monitored using the cutting force and the cutting temperature in the ball-end milling process by utilizing the response surface analysis with the Box-Behnken design. The optimum cutting condition is obtained referring to the minimum surface roughness, which is the spindle speed, the feed rate, the depth of cut, and the tool diameter. The models of cutting force ratio and the cutting temperature are proposed and developed based on the experimental results. It is understood that the surface roughness is improved with an increase in spindle speed, feed rate and depth of cut. The cutting temperature decreases with an increase in tool diameter. The model verification has showed that the experimentally obtained surface roughness model is reliable and accurate to estimate the surface roughness.

Taguchi Method Based Experiments of Titanium TC11 Flank Milling Parameters

2009 ◽  
Vol 407-408 ◽  
pp. 608-611 ◽  
Author(s):  
Chang Yi Liu ◽  
Cheng Long Chu ◽  
Wen Hui Zhou ◽  
Jun Jie Yi
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Flank Milling ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Mill Machining

Taguchi design methodology is applied to experiments of flank mill machining parameters of titanium alloy TC11 (Ti6.5A13.5Mo2Zr0.35Si) in conventional and high speed regimes. This study includes three factors, cutting speed, feed rate and depth of cut, about two types of tools. Experimental runs are conducted using an orthogonal array of L9(33), with measurement of cutting force, cutting temperature and surface roughness. The analysis of result shows that the factors combination for good surface roughness, low cutting temperature and low resultant cutting force are high cutting speed, low feed rate and low depth of cut.

scholarly journals Analysis of tool wear and surface roughness in high-speed milling process of aluminum alloy Al6061

2021 ◽  
pp. 71-84
Author(s):  
Nhu-Tung Nguyen ◽  
Dung Hoang Tien ◽  
Nguyen Tien Tung ◽  
Nguyen Duc Luan
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Tool Wear ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Speed ◽  
Milling Process ◽  
Face Milling ◽  
Depth Of Cut ◽  
High Speed Milling

In this study, the influence of cutting parameters and machining time on the tool wear and surface roughness was investigated in high-speed milling process of Al6061 using face carbide inserts. Taguchi experimental matrix (L9) was chosen to design and conduct the experimental research with three input parameters (feed rate, cutting speed, and axial depth of cut). Tool wear (VB) and surface roughness (Ra) after different machining strokes (after 10, 30, and 50 machining strokes) were selected as the output parameters. In almost cases of high-speed face milling process, the most significant factor that influenced on the tool wear was cutting speed (84.94 % after 10 machining strokes, 52.13 % after 30 machining strokes, and 68.58 % after 50 machining strokes), and the most significant factors that influenced on the surface roughness were depth of cut and feed rate (70.54 % after 10 machining strokes, 43.28 % after 30 machining strokes, and 30.97 % after 50 machining strokes for depth of cut. And 22.01 % after 10 machining strokes, 44.39 % after 30 machining strokes, and 66.58 % after 50 machining strokes for feed rate). Linear regression was the most suitable regression of VB and Ra with the determination coefficients (R2) from 88.00 % to 91.99 % for VB, and from 90.24 % to 96.84 % for Ra. These regression models were successfully verified by comparison between predicted and measured results of VB and Ra. Besides, the relationship of VB, Ra, and different machining strokes was also investigated and evaluated. Tool wear, surface roughness models, and their relationship that were found in this study can be used to improve the surface quality and reduce the tool wear in the high-speed face milling of aluminum alloy Al6061

scholarly journals Precision Hard Turning of Ti6Al4V Using Polycrystalline Diamond Inserts: Surface Quality, Cutting Temperature and Productivity in Conventional and High-Speed Machining

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5677
Author(s):  
Elshaimaa Abdelnasser ◽  
Azza Barakat ◽  
Samar Elsanabary ◽  
Ahmed Nassef ◽  
Ahmed Elkaseer
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
High Speed ◽  
Hard Turning ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Polycrystalline Diamond ◽  
Depth Of Cut ◽  
High Speed Machining ◽  
Conventional Machining

This article presents the results of an experimental investigation into the machinability of Ti6Al4V alloy during hard turning, including both conventional and high-speed machining, using polycrystalline diamond (PCD) inserts. A central composite design of experiment procedure was followed to examine the effects of variable process parameters; feed rate, cutting speed and depth of cut (each at five levels) and their interaction effects on surface roughness and cutting temperature as process responses. The results revealed that cutting temperature increased with increasing cutting speed and decreasing feed rate in both conventional and high-speed machining. It was found that high-speed machining showed an average increase in cutting temperature of 65% compared with conventional machining. Nevertheless, high-speed machining showed better performance in terms of lower surface roughness despite using higher feed rates compared to conventional machining. High-speed machining of Ti6Al4V showed an improvement in surface roughness of 11% compared with conventional machining, with a 207% increase in metal removal rate (MRR) which offered the opportunity to increase productivity. Finally, an inverse relationship was verified between generated cutting temperature and surface roughness. This was attributed mainly to the high cutting temperature generated, softening, and decreasing strength of the material in the vicinity of the cutting zone which in turn enabled smoother machining and reduced surface roughness.

The Effect of Vortex Tube Cooling on Surface Roughness and Carbon Footprint in Dry Turning

2014 ◽  
Vol 903 ◽  
pp. 135-138
Author(s):  
Zahari Taha ◽  
Hadi Abdul Salaam ◽  
Phoon Sin Ye ◽  
Tuan Muhammad Yusoff Shah Tuan Ya
Keyword(s):  
Surface Roughness ◽  
Carbon Footprint ◽  
Feed Rate ◽  
Vortex Tube ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Air Cooling ◽  
Coated Carbide

This paper presents a study on the effect of Ranque-Hilsch vortex tube air cooling on surface roughness quality and carbon footprint when turning mild steel workpiece with coated carbide cutting tool. The cutting parameters involved in this study were cutting speed, feed rate and depth of cut. The cutting speed and feed rate were fixed at 160 m/min and 0.10, 0.18 and 0.28 mm/rev, while the depth of cut was varied from 1.0 to 4.0 mm. During the turning process, the cutting temperatures were measured using infrared thermometer and the power consumption was measured using a power and harmonics analyzer and then converted into carbon footprint. The machined parts surface roughness were measured using a surface roughness tester. The results show that machining with Ranque - Hilsch vortex tube reduces the cutting temperature, but the surface roughness and carbon footprint is better under ambient condition except at a higher feedrate.

The Effect of Vortex Tube Air Cooling on Surface Roughness and Power Consumption in Dry Turning

2013 ◽  
Vol 310 ◽  
pp. 348-351 ◽  
Author(s):  
Hadi Abdul Salaam ◽  
Phoon Sin Ye ◽  
Zahari Taha ◽  
Tuan Muhammad Yusoff Shah Tuan Ya
Keyword(s):  
Surface Roughness ◽  
Power Consumption ◽  
Feed Rate ◽  
Vortex Tube ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Air Cooling ◽  
Coated Carbide

This paper presents a study of the effect of Ranque-Hilsch vortex tube air cooling on surface roughness quality and power consumption when turning mild steel material with coated carbide cutting tool. The cutting parameters involved in this study were cutting speed, feed rate and depth of cut. The cutting speed and feed rate were fixed at 160 m/min and 0.28 mm/rev, while the depth of cut was varied from 1.0 to 4.0 mm. During the turning process, the cutting temperatures were measured using an infrared thermometer and the power consumption was measured using a power and harmonics analyzer. The machined parts surface roughnesses were measured using a surface roughness tester. The results show that cooling using the Ranque-Hilsch vortex tube air cooling reduces the cutting temperature and the power consumption, but the surface roughness results is better when cooling with environment air.

The Effect of Cutting Speed and Feed Rate on Surface Roughness and Tool Wear when Machining Machining D2 Steel

2017 ◽  
Vol 909 ◽  
pp. 80-85 ◽  
Author(s):  
Mohd Rasidi Ibrahim ◽  
Tharmaraj Sreedharan ◽  
Nurul Aisyah Fadhlul Hadi ◽  
Mohammad Sukri Mustapa ◽  
Al Emran Ismail ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Surface Quality ◽  
Feed Rate ◽  
Input Parameter ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
D2 Steel

Machining parameters is a main aspect in performing turning operations using lathe machines. Cutting parameters such as cutting speed, feed rate and depth of cut gives big influence on the dynamic behavior of the machining system. In machining parts, surface quality and tool wear are the most crucial customer requirements. This is because the major indication of surface quality on machined part is the surface roughness and the value of tool wear. Hence, to improve the surface roughness and minimize the forming of tool wear, the optimum feed rate and cutting speed will be determined. The input parameter such as cutting speed, feed rate and depth of cut always influence the tool wear, surface roughness, cutting force, cutting temperature, tool life and dimensional accuracy. The D2 steel was being investigated from the perspective of the effect of cutting speed and feed rate on its surface roughness and tool wear. The results show that cutting speed is the main parameter which affects the surface roughness where the most optimum parameter would be at cutting speed of 173, 231 and 288 m/min with feed rate of 0.15 mm/rev. The tool wear strongly affected by feed rate where at 0.15 mm/rev the tool wear value is the lowest. The combination of high cutting speed and low feed rate was the best parameter to achieve smooth surface roughness.

Evaluation of Face Milling Operation Parameters on Surface Roughness of Crankcase Housing by Two Level Factorial Design with Center Points

2018 ◽  
Vol 780 ◽  
pp. 105-110
Author(s):  
Ukrit Thanasuptawee ◽  
Chamrat Thakhamwang ◽  
Somsak Siwadamrongpong
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Milling Process ◽  
Face Milling ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Significance Level ◽  
Machining Center ◽  
Semi Solid

In this study, there are three machining parameters consist of spindle speed, feed rate and depth of cut which were conducted through full factorial with four center points to determine the effect of machining parameters on the surface roughness and verify whether there is curvature in the model for CNC face milling process in an automotive components manufacturer in Thailand. The workpieces used semi-solid die casted ADC12 aluminum alloy crankcase housing which they were performed by the ARES SEIKI model R5630 3-axis CNC vertical machining center and face milling cutter with diameter of 63 millimeters. The surface roughness of face-milled was measured by the surface roughness tester. It was found that the greatest main effect influence to surface roughness was spindle speed, followed by feed rate and depth of cut at significance level of 0.05.

Optimization and Prediction of Cutting Force and Surface Roughness in End Milling Process of AISI 304 Stainless Steel

2015 ◽  
Vol 813-814 ◽  
pp. 362-367 ◽  
Author(s):  
Darshan A. Patel ◽  
Jitendra M. Mistry ◽  
Vrushit P. Kapatel ◽  
Dhaval R. Joshi
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
End Milling ◽  
Milling Process ◽  
304 Stainless Steel ◽  
Depth Of Cut ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304 ◽  
End Milling Process

The end milling process is most commonly used where the large amount material can be removed to produce almost final shape of component. The present work deals with the experimental study and optimization the machining parameter of AISI 304 stainless steel. The effects of spindle speed, feed rate and depth of cut have been studied on the cutting force and surface roughness using Taguchi’s 27 orthogonal arrays. Regression analyses were used to develop the model of response parameters. The analysis of the result shows, the surface roughness and the cutting force is increased with feed rate and depth of cut but decreased with increased the cutting speed. The ANOVA indicate the feed rate was the most dominate parameter on surface roughness and cutting force than speed and depth of cut.

Study on Machinability of 35CrMnSiA Steel in Hard Turning Process

2006 ◽  
Vol 532-533 ◽  
pp. 349-352
Author(s):  
Wen Xiang Zhao ◽  
Si Qin Pang ◽  
Zhen Hai Long ◽  
Xi Bin Wang
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
High Strength ◽  
Depth Of Cut ◽  
Turning Process ◽  
High Speed Turning ◽  
Cutting Velocity ◽  
Strength Alloy

35CrMnSiA, is a kind of important engineering materials that used widely in modern manufacturing fields. The machinability of 35CrMnSiA Steel with hardness of HRc40±2 in high speed turning process was studied in this paper. It is concluded that, when high speed turning of this ultra-high strength alloy steel, the chief wear mode of ceramics is the crater on rake faces; the interaction of depth of cut and feed rate is one of statistic significant effects on cutting force; the interaction of cutting velocity of cut and feed rate is one of statistic significant effects on surface roughness Ra; besides, the empirical formula of average cutting temperature, cutting forces, surface roughness Ra, was established.

Sign in / Sign up

Export Citation Format

Share Document